Access to Power -SOG 30-day Challenge! Starting June 1st! Access & Access Deluxe
-
@Dutch_Tooler said:
In my book that qualifies as an imaginative use, Wspeed 
+1
just beware that files (if we can call this one a file ::) :D) are usually hardened so should not be used to pry, twist or torque as they easily snapped
but I see that you used it putting the force closer to the pivot thus reducing the leverage multiplication effect 
-
cutting test
I used the SOG PAD and PA
And the LM Crunch and the LM Supertool
For this test I have 8 different type wires
I started with the really thin wire copper and metal
Then had 4 different thickness of electrical wire
The brown wire has a solid copper wire
And 2 different size trimmer wireThe first 2 pics is what I tested the MTs with
The PAD and PA both didn’t have any
problems cutting the 8 different size wiresOnly the LM Crunch didn’t cut the
green trimmer wire on one of the cuts


-
The PAD
Cut everything no problems


-
The PA
Cut everything no problems


-
The LM Crunch
Only had one cut on the green
trimmer wire it had a problem with

-
The LM Supertool
No problems
I have just about tested
everything I can with the SOG PAD
On day 11 I tested zip ties stainless
welding wire and a hardened 2.5mm nail
As well as trimmer wire and electric wire
And again for the 2nd test it cut everything


-
In my book that qualifies as an imaginative use, Wspeed 
+1
just beware that files (if we can call this one a file ::) :D) are usually hardened so should not be used to pry, twist or torque as they easily snapped
but I see that you used it putting the force closer to the pivot thus reducing the leverage multiplication effect 
Good point D_T I do think anything
tighter and it would of snapped off
-
Nice testing, guys!
(And D_T, good work with the checklist. Your cap-lifter is clearly well tested.
)I scrounged up a few extra bits of wire to test, will post a pic later.

-
@Don Pablo said:
So if I understand the chart, the PAD got more passes than the Swisstool and Wave, and the Surge was the only one to get three passes.
Indeed. It seems strange, but remember, the tests involved no twisting or pulling while using the cutters on stranded wire & tiny solid core wire(these were intentionally chosen, because they are notoriously aggravating to cut) Every tool tested can cut most stuff when "manipulated" a bit.
And don't be put-off my results. I needed a standard of testing and obviously most of us don't cut stuff exactly the same way.Usually, when I cut zip ties, electrical wire and thin steel wire, I angle and pull the wire up towards the cutter blade(i just cut straight on in the the tests). This makes for cleaner cuts and reduces strain on the jaw pivot. Every tool I have will cut most stuff this way.
Non of the tools tested would need this kind of manipulation with thicker (or stronger) materials like bailing wire.Pic of what I mean attached at bottom. The pic is showing a powerpint, because I am having my off-day coffe and can't be bothered to go get the pad right now. :P
Today I was checking the fluid levels in the engine bay
And needed something to open the power steering cap
Normally I use a large screwdriver but as I got the PAD
I found the file to be just right for removing the capI think you win most creative file use.

And thank you for doing all of your testing. Seems your PAD has an excellent cutter section!


-
Can we agree that Gerbers replaceable cutters suck? :)
-
Thanks GLBM

If there is anything else you would like
me to test the cutters with let me knowSo far the cutters have cut everything i can think of
The pliers on my PAD seem to be good quality
-
@Don Pablo said:
Can we agree that Gerbers replaceable cutters suck? :)Hell yes. They have to be the worst cutter system ever designed. Everything from my early replaceable-cutter MP600 to my Center-Drive look like piranhas when I try to cut wire with them.
You saw the chart. The Gerber failed all three. And if you look at the photos, it barely tore the jackets off of the wire.
The CD isn't as bad as that mp600, but it is definitely at the bottom of the totem-pole(sp?).
-
Day 13:
More wire cutter testing:

All wires are steel (checked with magnet). The top most wire is thick and heavy, about the thickness of a 14-16g finishing nail. The second from the top is a standard medium-gauge wire. Third down is a fine, coated garden wire used for tying up plants. The bottom is a common "twist-tie".
The PAD chomped through the thick wire without difficulty. As I cut the medium wire, I felt it twist a little, then it cut fairly well. In the case of the garden wire and twist tie, the wires just bent.
So, my PAD will cut fairly heavy wire with relative ease. The cutters have sustained no damage so far (checked with 5x magnifier). However, thinner wire and stranded wire seems to stymie my PAD. As does mono-filament and perhaps a zip tie (variable results with zip ties).
This is a real set back for me. Fishing is one of those activities where I always try to have a multi-tool with me. While I typically use scissors to cut mono, it's nice to have the ability to use a multitool if it is already in hand.
As well, I do a fair bit of work in the garden in the summer, so not being able to use a multitool to cut simple garden wire is another disappointment.
Right at the moment, my PAD is bumming me out. If it weren't for you guys and the challenge(s), I'd be tempted to pitch the thing.
For comparison, I tried using a LM Juice to tackle the same wires:

No problems.
No damage (checked with 5x magnifier).
I will say, the Juice had difficulty with the orange mono that I tried cutting yesterday. The Juice has also failed to cut double-stranded barbed wire for me in the past. If it ever stops raining, I'll try to get out for a hike and test the PAD against double stranded barbed wire. I have cut double stranded barbed wire successfully with a Charge and a Rebar. It is a tough task though.
-
Thank you for the comparison, Nix!
I would be willing to be there is some play in those plier jaws. Might be worth peening the pivot a bit(or trying that method someone came up with using vise-grips). Only because you are using them for the summer and will need them to work. Definitely not saying sloppy plier jaws are o.k.
-
There is definitely some play in the pliers.
I can grab the ends of the pliers head and move the jaws side-to-side.


I may try peening. I'm curious to see how SOG wants to resolve the file issue first.
I'm not familiar with the Vise Grip technique.

-
BTW, sent SOG an email on Saturday in re the file. Haven't heard back from them yet, but it's still early out on the West coast.
And they may be busy.... ::)
-
Hehe. They may be up to their eyeballs in repair/exchange requests.

I can't be too hard on them about slight plier play though. I've experienced plier play on brand new tools with every brand. Heck, I received a LM OHT once that I could literally cross the jaw tips over one-another. The replacement was close to as bad. :-
It shouldn't happen though, even if other companies do ship out sloppy jaws, doesn't mean everyone should do it.
This is an issue I take to be blatantly careless, whether it is LM, Vic, Gerber, Bear, or SOG. Loose pliers are not exactly hard to check for in QC and everyone seems to still ship out MTs with slightly sloppy jaws(Vic and Gerber are pretty good about not having jaw play often though).
I wish they would ship the tools with the pivot a bit tight to allow some break in. If they ship the tool with a loose plier pivot, it is going to be horribly loose after the break in period.
Since my take on this is a topic for general tool discussion, I'll just hush about it now.
Back to the PAD. What to do. What to do on my lazy day off with the PAD.
-
Totally agree GLBM it should not happen

You could always open some
cans or bottles on your lazy day :D
-
Nix,
I must apologize. The fix I was thinking about has only been demonstrated to work on LM pivots. Not sure if a SOG pivot would move with the technique. Would it be the end of the world if trying it on the SOG didn't work? :D
The thread has a few good peening techniques shown/linked/mentioned as well. Not sure which peening technique you're used to using though.
Here is that thread. /post/1606879
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login