Access to Power -SOG 30-day Challenge! Starting June 1st! Access & Access Deluxe
-
Thank you for the comparison, Nix!
I would be willing to be there is some play in those plier jaws. Might be worth peening the pivot a bit(or trying that method someone came up with using vise-grips). Only because you are using them for the summer and will need them to work. Definitely not saying sloppy plier jaws are o.k.
-
There is definitely some play in the pliers.
I can grab the ends of the pliers head and move the jaws side-to-side.


I may try peening. I'm curious to see how SOG wants to resolve the file issue first.
I'm not familiar with the Vise Grip technique.

-
BTW, sent SOG an email on Saturday in re the file. Haven't heard back from them yet, but it's still early out on the West coast.
And they may be busy.... ::)
-
Hehe. They may be up to their eyeballs in repair/exchange requests.

I can't be too hard on them about slight plier play though. I've experienced plier play on brand new tools with every brand. Heck, I received a LM OHT once that I could literally cross the jaw tips over one-another. The replacement was close to as bad. :-
It shouldn't happen though, even if other companies do ship out sloppy jaws, doesn't mean everyone should do it.
This is an issue I take to be blatantly careless, whether it is LM, Vic, Gerber, Bear, or SOG. Loose pliers are not exactly hard to check for in QC and everyone seems to still ship out MTs with slightly sloppy jaws(Vic and Gerber are pretty good about not having jaw play often though).
I wish they would ship the tools with the pivot a bit tight to allow some break in. If they ship the tool with a loose plier pivot, it is going to be horribly loose after the break in period.
Since my take on this is a topic for general tool discussion, I'll just hush about it now.
Back to the PAD. What to do. What to do on my lazy day off with the PAD.
-
Totally agree GLBM it should not happen

You could always open some
cans or bottles on your lazy day :D
-
Nix,
I must apologize. The fix I was thinking about has only been demonstrated to work on LM pivots. Not sure if a SOG pivot would move with the technique. Would it be the end of the world if trying it on the SOG didn't work? :D
The thread has a few good peening techniques shown/linked/mentioned as well. Not sure which peening technique you're used to using though.
Here is that thread. /post/1606879 -
Decided to get off my lazy hind-end and rummage through my canned food pantry. Found two cans of beans(both passed their sell by :D ) and a can of water chestnuts(I don't eat these. Don't know why I had them).
The can opener on my PAD performed exactly like I had imagined. Not great, but worked as advertised. It really wasn't that much worse than the SAK can opener in my opinion.
Pics 1/2



-
Pics 2/2.




-
Nice one GLBM

Your cans look the same as the cans I did
After the challenge I will have a go at
Trying to get a better cutting edge on the can opener
-
Thank you, W!

To be honest, as lame as the PAD can opener is, I don't think much better about any other one-piece openers on knives/saks/MTs.
I am not sure, with pull ring cans being the normal thing now, it is worth sharpening it. It will work in the .001% chance you may be stuck with it as the only can opener available. -
I think the can openers on the Vic SAKs are light years better than the PAD's can opener.
But, as you noted, the PAD can get the job done.
And I've had more practice with the Vic openers.
-
At least the can opener will work in emergency’s

I want to give it a cutting edge like on the LM ones
And make the point on the can opener a bit sharper
Hopefully I might get easier cutting through the lid

-
I am spoiled with electric can openers and handheld circular-blade can openers. I don't have much practice with MT/SAK openers. And, to be honest, I have only used the can opener on my EDC Explorer a couple of times in about ten years.
I am going to have to roll with your(and others) conclusion, regarding your experience(vic opener being much better)on this topic, Nix!

-
Day 13 (continued):
I noticed that the back gate latch was a bit loose after the Winter. I used the integral bit holder and the #1 Philips to tighten this back up. Might need to be replaced, but this will hold the dog in for now. :D

-
interesting challenge so far!
so, seeing the results, I can say that the can opener is Pitiful And Disastrous,
it also seems like the alignment of the jaws can be Problematic And Dysfunctional
the innovative feature of the centerline bit driver is Passable And Decent,
we could also agree that in a way the tool itself is has good Pliers And Drivers
but it really lacks and leaves you cold if we talk about the Protractor And Durability of the tool
The cutters are still being tested by all of you with Perseverance And Dedication to have a verdict on them:D
now I'll stop Playing And Distracting as I always do,

and encourage you to keep on with this very interesting challenge

-
Nicely done TP! 
Regardless of what we are discussing, I am not overly Perturbed And Discordant about it, yet.

-
Day 18:
Took the PAD outside for some fresh air.
SOG PowerAccess Deluxe by None, on Flickr
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
