Access to Power -SOG 30-day Challenge! Starting June 1st! Access & Access Deluxe
-
Nice one GLBM

Your cans look the same as the cans I did
After the challenge I will have a go at
Trying to get a better cutting edge on the can opener
-
Thank you, W!

To be honest, as lame as the PAD can opener is, I don't think much better about any other one-piece openers on knives/saks/MTs.
I am not sure, with pull ring cans being the normal thing now, it is worth sharpening it. It will work in the .001% chance you may be stuck with it as the only can opener available. -
I think the can openers on the Vic SAKs are light years better than the PAD's can opener.
But, as you noted, the PAD can get the job done.
And I've had more practice with the Vic openers.
-
At least the can opener will work in emergency’s

I want to give it a cutting edge like on the LM ones
And make the point on the can opener a bit sharper
Hopefully I might get easier cutting through the lid

-
I am spoiled with electric can openers and handheld circular-blade can openers. I don't have much practice with MT/SAK openers. And, to be honest, I have only used the can opener on my EDC Explorer a couple of times in about ten years.
I am going to have to roll with your(and others) conclusion, regarding your experience(vic opener being much better)on this topic, Nix!

-
Day 13 (continued):
I noticed that the back gate latch was a bit loose after the Winter. I used the integral bit holder and the #1 Philips to tighten this back up. Might need to be replaced, but this will hold the dog in for now. :D

-
interesting challenge so far!
so, seeing the results, I can say that the can opener is Pitiful And Disastrous,
it also seems like the alignment of the jaws can be Problematic And Dysfunctional
the innovative feature of the centerline bit driver is Passable And Decent,
we could also agree that in a way the tool itself is has good Pliers And Drivers
but it really lacks and leaves you cold if we talk about the Protractor And Durability of the tool
The cutters are still being tested by all of you with Perseverance And Dedication to have a verdict on them:D
now I'll stop Playing And Distracting as I always do,

and encourage you to keep on with this very interesting challenge

-
Nicely done TP! 
Regardless of what we are discussing, I am not overly Perturbed And Discordant about it, yet.

-
Day 18:
Took the PAD outside for some fresh air.
SOG PowerAccess Deluxe by None, on Flickr -
Nice shot, G-man.

I think the PAD is a nice looking tool with some personality and dash.
-
Thank you, Nix !

-
Excellent pic GLBM

-
Day 13 (continued):
After the discussion with G-man above, I decided to regrind the Can Opener. I used a mill file, diamond sharpener, and sandpaper to create more of an edge on the semicircular cutting edge. This is where the Can Opener does it's work. SOG sharpened (to a limited extent) the straight inner edge. This makes no sense as the inner edge isn't involved in opening a can (although it may be useful for peeling an orange.).
Between this and the file, I get the impression the tools were designed by somebody who had seen a picture of other tools, but has no idea how they are supposed to work. It's like the design is aping some dimly recollected tool set from a lost civilization. Hey, maybe that's where we are these days.

The new can opener now works fairly well. Maybe not SAK efficacy, but it is much improved over the can opener as received. In the photo, the point or tip of the opener looks rounded. This is misleading as the tip is actually pretty sharp. I like the new "shark's tooth" look of this opener now.
-
Thank you, W!
Very nice, Nix! Maybe, when you inevitably have to send it in for warranty work, SOG can reverse engineer your reprofiled can opener and use the ancient technology to create a more effective one.

-
@gerleatherberman said:
Very nice, Nix! Maybe, when you inevitably have to send it in for warranty work, SOG can reverse engineer your reprofiled can opener and use the ancient technology to create a more effective one.
That is so NOT funny.

(I actually had the same thought myself. )
-
Looks good Nix

Would love to see some pics of a can you used it on
-
So, SOG got back to me.......
Hello,
We are sending you a replacement clip for your Power Access multi tool.
Thank you,
AmandaWhy do I get the impression we've had a failure to communicate?

-
How many PA clips got broken where the automatic response is to send a new clip?
I am seriously LOL'ing here.
If you send a correction email in reply, and they still send you a clip, I am going to die laughing(sorry. I can't help it).
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login