Torx sizes?
-
Good question, boss.
While evaluating the SOG PAD, I realized that most of the included Torx bits are probably smaller than I typically use. But that may just be me and my world. I'll get back on this question with some more detailed answers and reasons.
-
@hiraethus said:
T6 = aftermarket SAK pivot fixing screws
Security T10 = Leatherman Wave screwsAlso, add a 2mm or 5/64" hex key for Sebenza pivot screws

I am thinking a T8 works for the replaceable cutters
Can someone else confirm this
Been a while since I have had to tighten any so I can't remember for sure 
-
T6, T8, T9, T10, T15 and T25 - I think you'd be well covered with that. Also, make sure you get Torx Pro or Tamper Proof (the ones with the hole) as then you'll be doubly covered!

-
Lately I remember using T20, T25 and T27 for various wood screws. Not sure if that counts as everyday use though.
-
It was only a few days ago that I learned of the existence of torx wood screws by finding them in Lidl.

-
Here are my votes:
T-27: used in motorcycle
T-25: also used in motorcycle
T-15: also used in motorcyle and handy for some general purpose screws
T-8 : fasteners in some folding knives
T-6 : myriad uses in gear, clips, knives, custom SAK boltsI also seem to think T-10's are useful, but I can't recall why.........

-
I use T10, T15 and T20 daily for install purposes.
Now, like others said, get the security version whenever you can. The hole doesn't matter on regular Torx screws, but are needed on the security ones.
Before Torx, we used Robertsons in our company. No2 I think it was...
They were dirt cheap since nobody bought those Canadian things here and at the same time, other people couldn't open our equipment because they didn't realise a flathead would fit too
-
T-27: used in motorcycle
T-25: also used in motorcycle
T-15: also used in motorcyle and handy for some general purpose screws
T-8 : fasteners in some folding knives
T-6 : myriad uses in gear, clips, knives, custom SAK boltsI also seem to think T-10's are useful, but I can't recall why.........

This!
Matches my list, but as mentioned I would include the T-10. With these sizes you should be pretty well covered for all your knife clip, handle, and pivot screws, as well as the larger sizes for car/motorcycle matenince. I would highly suggest including a T-50 and T-55 if you plan on any sort of car matenence though. Definitely buy them in the security torx variety as the security torx can be used on security and non security bits just the same. If you are planning on piecing toghether a set I would just buy a complete set to be honest. Some sets do not include all these sizes mentioned and if so you can buy a single bit to accommodate your needs. Also, there are many different types of torx bits out there. Different amount of points. 5 or 6 point, both in security and non security. As well as torx plus and pentalobe. I believe there are at least 2 or 3 other style torx as well in security and non security varieties. The most common are 5 or 6 point (6 point is the most common if I remember correctly) so I would stick with those for now.
-
+1 on T6, T8, and T10 if you expect to fiddle with folding knives. Seems like that’s all I use for those. For fixed blades maybe include hex for the scales, just depends on your knife for the size.
That how I carry my bIts is I carry only what I typically use plus a few not so used.
Good stuff man, made me rethink what I have in my bag. Thanks for that.
-
T6, T8, T10, TX10, T15, T25 and T40 cover 99% of all the Torx in computers. Throw in T20, T27 and T30 and you have covered all but smartphones / tablets and some exotic stuff.
Around here Spax screws are fairly common for wooden constructions, so a T20plus (there are others, but the T20plus covers most of it and unlike safety torx, regular ones work with Spax screws, just don't fit as well) would complete the listI have encountered T5 on a toy car and a T7 on a cheapo pocket calculator.
-
@Poncho65 said:
I am thinking a T8 works for the replaceable cutters
Can someone else confirm this
Been a while since I have had to tighten any so I can't remember for sure 
Yup, Leatherman replaceable wire-cutters are Torx 8.
Torx 8 and sometimes 9 are also used by off-brand multi-tools, like Coast and Ganzo.
Bear & Son multi-tools also use T10. -
as others said, T6, T8, and T10 cover 95% of the Torx found in tools, multitools, pocket knives' pivots, clips and hardware, and other gear like some lights, lighters, stoves, gizmos and gadgets

These are the ones I carry everywhere

-
for my uses i carry T6,T8,T15,T20 all in security bits (with the hole down the center)
it seems at least 50% of the torx i come across are security screws in things like camera housings, lock hardware and various equipment. -
T6, T8 and T10 for SAKs, MTs and folders...

Sent from my iPhone using Tapatalk
-
What's used the most from me is T8, T10, T15 ...and T30 sometimes for centering the disc brakes on my MTB.
But as I like to be prepared I end up packing T8, T10 and T15 into my Rebar sheath.
And T10, T15, T20, T27 and T30 into my Surge sheath.

-
So, for those of you who lost count......
T-6 : 9
T-8 : 11
T-9 : 2
T-10: 11
T-15: 7
T-20: 5
T-25: 5
T-27: 4
T-30: 1
T-40: 1
T-50: 1
T-55: 1 -
@Nix said:
So, for those of you who lost count......T-6 : 9
T-8 : 11
T-9 : 2
T-10: 11
T-15: 7
T-20: 5
T-25: 5
T-27: 4
T-30: 1
T-40: 1
T-50: 1
T-55: 1Thanks...
Seems about right. T27 and smaller from this list probably cover most of torx needs around the globe. T6/8/10 will probably service any knife.
-
A small note about the security hole vs not. The security ones will fit all and are more versatile for that reason. However they are also weaker. I've twisted off at least two security hole ones (that I can remember), and that has never happened to me with a normal torx bit.
Small Torx sizes are also common on indexable tools used in machining. Those are better used with some torque wrench - that might be theme for other Torx uses too?
-
This is a great list
T-6 : 9
T-8 : 11
T-9 : 2
T-10: 11
T-15: 7
T-20: 5
T-25: 5
T-27: 4
T-30: 1
T-40: 1
T-50: 1
T-55: 1Problem is no matter what I have on me I always need the one I don't have. ???
I think design engineers change things up like that on purpose.

-
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login