Torx sizes?
-
I use T10, T15 and T20 daily for install purposes.
Now, like others said, get the security version whenever you can. The hole doesn't matter on regular Torx screws, but are needed on the security ones.
Before Torx, we used Robertsons in our company. No2 I think it was...
They were dirt cheap since nobody bought those Canadian things here and at the same time, other people couldn't open our equipment because they didn't realise a flathead would fit too
-
T-27: used in motorcycle
T-25: also used in motorcycle
T-15: also used in motorcyle and handy for some general purpose screws
T-8 : fasteners in some folding knives
T-6 : myriad uses in gear, clips, knives, custom SAK boltsI also seem to think T-10's are useful, but I can't recall why.........

This!
Matches my list, but as mentioned I would include the T-10. With these sizes you should be pretty well covered for all your knife clip, handle, and pivot screws, as well as the larger sizes for car/motorcycle matenince. I would highly suggest including a T-50 and T-55 if you plan on any sort of car matenence though. Definitely buy them in the security torx variety as the security torx can be used on security and non security bits just the same. If you are planning on piecing toghether a set I would just buy a complete set to be honest. Some sets do not include all these sizes mentioned and if so you can buy a single bit to accommodate your needs. Also, there are many different types of torx bits out there. Different amount of points. 5 or 6 point, both in security and non security. As well as torx plus and pentalobe. I believe there are at least 2 or 3 other style torx as well in security and non security varieties. The most common are 5 or 6 point (6 point is the most common if I remember correctly) so I would stick with those for now.
-
+1 on T6, T8, and T10 if you expect to fiddle with folding knives. Seems like that’s all I use for those. For fixed blades maybe include hex for the scales, just depends on your knife for the size.
That how I carry my bIts is I carry only what I typically use plus a few not so used.
Good stuff man, made me rethink what I have in my bag. Thanks for that.
-
T6, T8, T10, TX10, T15, T25 and T40 cover 99% of all the Torx in computers. Throw in T20, T27 and T30 and you have covered all but smartphones / tablets and some exotic stuff.
Around here Spax screws are fairly common for wooden constructions, so a T20plus (there are others, but the T20plus covers most of it and unlike safety torx, regular ones work with Spax screws, just don't fit as well) would complete the listI have encountered T5 on a toy car and a T7 on a cheapo pocket calculator.
-
@Poncho65 said:
I am thinking a T8 works for the replaceable cutters
Can someone else confirm this
Been a while since I have had to tighten any so I can't remember for sure 
Yup, Leatherman replaceable wire-cutters are Torx 8.
Torx 8 and sometimes 9 are also used by off-brand multi-tools, like Coast and Ganzo.
Bear & Son multi-tools also use T10. -
as others said, T6, T8, and T10 cover 95% of the Torx found in tools, multitools, pocket knives' pivots, clips and hardware, and other gear like some lights, lighters, stoves, gizmos and gadgets

These are the ones I carry everywhere

-
for my uses i carry T6,T8,T15,T20 all in security bits (with the hole down the center)
it seems at least 50% of the torx i come across are security screws in things like camera housings, lock hardware and various equipment. -
T6, T8 and T10 for SAKs, MTs and folders...

Sent from my iPhone using Tapatalk
-
What's used the most from me is T8, T10, T15 ...and T30 sometimes for centering the disc brakes on my MTB.
But as I like to be prepared I end up packing T8, T10 and T15 into my Rebar sheath.
And T10, T15, T20, T27 and T30 into my Surge sheath.

-
So, for those of you who lost count......
T-6 : 9
T-8 : 11
T-9 : 2
T-10: 11
T-15: 7
T-20: 5
T-25: 5
T-27: 4
T-30: 1
T-40: 1
T-50: 1
T-55: 1 -
@Nix said:
So, for those of you who lost count......T-6 : 9
T-8 : 11
T-9 : 2
T-10: 11
T-15: 7
T-20: 5
T-25: 5
T-27: 4
T-30: 1
T-40: 1
T-50: 1
T-55: 1Thanks...
Seems about right. T27 and smaller from this list probably cover most of torx needs around the globe. T6/8/10 will probably service any knife.
-
A small note about the security hole vs not. The security ones will fit all and are more versatile for that reason. However they are also weaker. I've twisted off at least two security hole ones (that I can remember), and that has never happened to me with a normal torx bit.
Small Torx sizes are also common on indexable tools used in machining. Those are better used with some torque wrench - that might be theme for other Torx uses too?
-
This is a great list
T-6 : 9
T-8 : 11
T-9 : 2
T-10: 11
T-15: 7
T-20: 5
T-25: 5
T-27: 4
T-30: 1
T-40: 1
T-50: 1
T-55: 1Problem is no matter what I have on me I always need the one I don't have. ???
I think design engineers change things up like that on purpose.

-
-
@Vidar said:
A small note about the security hole vs not. The security ones will fit all and are more versatile for that reason. However they are also weaker. I've twisted off at least two security hole ones (that I can remember), and that has never happened to me with a normal torx bit.+1. Has happened to me on more than one occasion.
-
So which one(s) specifically would need to be security bits?
Def
-
Me, I'd stick with the stronger, standard bits unless I had a specific need for a security bit.
I've run into a couple of situations where a security bit was required, but that seems very rare. I can't actually recall when I last needed a security Torx. (My experience only.)
When traveling by car or motorcycle, I usually have a set of folding Torx drivers in a tool bag.

Interesting to note that the drivers that show the most use/wear are T-10, T-20, T-25, and T-27.
-
A small note about the security hole vs not. The security ones will fit all and are more versatile for that reason. However they are also weaker. I've twisted off at least two security hole ones (that I can remember), and that has never happened to me with a normal torx bit.
+1. Has happened to me on more than one occasion.
+2
-
I had some small 4mm hex drive Torx bits but a couple stripped and I never replaced them. :-\
What I currently have is good for most everything except the smaller electronics sizes, T5 through T9 (which I should get).

In my tool bag in Vic holders, T10,15, 20, 25, 27, 30, and 40. Also the 5 pointed ones from Loki for LM's, 2 of each, all security.
In my toolbox, 1/4" socket T15, 20, 25, and 3/8" socket T30, 40, 45, 50. Also separate T60 which I think I needed for a seat belt attachment, and an old T15 I got many years ago when they switched from using Phillips to Torx (almost all T15 at the time) on automotive trim.


-
@Grant Lamontagne said:
So which one(s) specifically would need to be security bits?Def
In my job i come across security screws probably 80% of the time (facility maintenance)
usually its T6,T8, T15 and T20
T6 and T8 tend to be used on security camera housings and T15 would be for electronic door locks.
T15 and T20 are commonly used on equipment like vacuums, carpet extractors and kitchen equipment, elevators and fire panels. they are becoming more popular in alot of places.
it's strange that this topic has come up because i have been planning on modifying some of my leatherman bits by drilling a hole down the center to turn them into security bits! (i'll show pics when i'm done)it's true f you use them on regular Torx screws you do have to be careful because the torque can be too much for them and you will tare them apart. they usually last me for a few months anyways.
i think this is because they are usually not impact ready hardened metal like alot of bits are now. at least the ones i seem to get.
they also work in similar sized Allen screws as well but can shorten the lifespan and so i figure it's worth it to carry less bits and replace more often
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login