Torx sizes?
-
for my uses i carry T6,T8,T15,T20 all in security bits (with the hole down the center)
it seems at least 50% of the torx i come across are security screws in things like camera housings, lock hardware and various equipment. -
T6, T8 and T10 for SAKs, MTs and folders...

Sent from my iPhone using Tapatalk
-
What's used the most from me is T8, T10, T15 ...and T30 sometimes for centering the disc brakes on my MTB.
But as I like to be prepared I end up packing T8, T10 and T15 into my Rebar sheath.
And T10, T15, T20, T27 and T30 into my Surge sheath.

-
So, for those of you who lost count......
T-6 : 9
T-8 : 11
T-9 : 2
T-10: 11
T-15: 7
T-20: 5
T-25: 5
T-27: 4
T-30: 1
T-40: 1
T-50: 1
T-55: 1 -
@Nix said:
So, for those of you who lost count......T-6 : 9
T-8 : 11
T-9 : 2
T-10: 11
T-15: 7
T-20: 5
T-25: 5
T-27: 4
T-30: 1
T-40: 1
T-50: 1
T-55: 1Thanks...
Seems about right. T27 and smaller from this list probably cover most of torx needs around the globe. T6/8/10 will probably service any knife.
-
A small note about the security hole vs not. The security ones will fit all and are more versatile for that reason. However they are also weaker. I've twisted off at least two security hole ones (that I can remember), and that has never happened to me with a normal torx bit.
Small Torx sizes are also common on indexable tools used in machining. Those are better used with some torque wrench - that might be theme for other Torx uses too?
-
This is a great list
T-6 : 9
T-8 : 11
T-9 : 2
T-10: 11
T-15: 7
T-20: 5
T-25: 5
T-27: 4
T-30: 1
T-40: 1
T-50: 1
T-55: 1Problem is no matter what I have on me I always need the one I don't have. ???
I think design engineers change things up like that on purpose.

-
-
@Vidar said:
A small note about the security hole vs not. The security ones will fit all and are more versatile for that reason. However they are also weaker. I've twisted off at least two security hole ones (that I can remember), and that has never happened to me with a normal torx bit.+1. Has happened to me on more than one occasion.
-
So which one(s) specifically would need to be security bits?
Def
-
Me, I'd stick with the stronger, standard bits unless I had a specific need for a security bit.
I've run into a couple of situations where a security bit was required, but that seems very rare. I can't actually recall when I last needed a security Torx. (My experience only.)
When traveling by car or motorcycle, I usually have a set of folding Torx drivers in a tool bag.

Interesting to note that the drivers that show the most use/wear are T-10, T-20, T-25, and T-27.
-
A small note about the security hole vs not. The security ones will fit all and are more versatile for that reason. However they are also weaker. I've twisted off at least two security hole ones (that I can remember), and that has never happened to me with a normal torx bit.
+1. Has happened to me on more than one occasion.
+2
-
I had some small 4mm hex drive Torx bits but a couple stripped and I never replaced them. :-\
What I currently have is good for most everything except the smaller electronics sizes, T5 through T9 (which I should get).

In my tool bag in Vic holders, T10,15, 20, 25, 27, 30, and 40. Also the 5 pointed ones from Loki for LM's, 2 of each, all security.
In my toolbox, 1/4" socket T15, 20, 25, and 3/8" socket T30, 40, 45, 50. Also separate T60 which I think I needed for a seat belt attachment, and an old T15 I got many years ago when they switched from using Phillips to Torx (almost all T15 at the time) on automotive trim.


-
@Grant Lamontagne said:
So which one(s) specifically would need to be security bits?Def
In my job i come across security screws probably 80% of the time (facility maintenance)
usually its T6,T8, T15 and T20
T6 and T8 tend to be used on security camera housings and T15 would be for electronic door locks.
T15 and T20 are commonly used on equipment like vacuums, carpet extractors and kitchen equipment, elevators and fire panels. they are becoming more popular in alot of places.
it's strange that this topic has come up because i have been planning on modifying some of my leatherman bits by drilling a hole down the center to turn them into security bits! (i'll show pics when i'm done)it's true f you use them on regular Torx screws you do have to be careful because the torque can be too much for them and you will tare them apart. they usually last me for a few months anyways.
i think this is because they are usually not impact ready hardened metal like alot of bits are now. at least the ones i seem to get.
they also work in similar sized Allen screws as well but can shorten the lifespan and so i figure it's worth it to carry less bits and replace more often -
For knives, T6, T8 and T10, can't remember on which knife I used T10, but I bought mine for working on HP printers many moons ago....only one you need.
The above are all single tools, I have all the other sizes in bits........don't think I've ever used them

-
I think the handles/scales on the Charge require a security T-10.
I can't be sure, because I don't have a Security T-10 bit.....

-
worst thing about security bits is that its hard to find individual bits, i usually end up buying a complete set everytime i need one new bit!
-
You and me both. I have about ten bit sets, all of which missing the same bits.

Def
-
Only came across leatherman tools which require T10 security bits.... others are just plain torx... of course some old LM tools have the 5 pointed star instead of the 6 pointed star T10s...
Sent from my iPhone using Tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login