Access to Power -SOG 30-day Challenge! Starting June 1st! Access & Access Deluxe
-
in general I've found SOG blades to be well hardened, good cutters (geometry and factory edge) and tough (for drilling, prying, scraping and bending which I've admittedly done with them
)the one in my Blacktip is excellent, good grind, smooth and solid, long and wide, reminds me of a SAK blade
::)Spoiler:

and the one in the PP came *super *sharp :ahhh and the serrated portion cut effectively rope and wrapping bands, while the PE did great in cutting boxes and scraping wood splinters and slivers in my old wooden windows

Spoiler:

I prefer them to Leatherman, Victorinox and Gerber blades for the most part (except for the Wave, Surge and MP800 blades)

-
My PE blade is very sharp it
can even shave hair off my arm
Nice cut TP
-
Day 21. Not my usual work, but used the bit set and driver on the PAD to remove and re-install(after repair) the broken door to a kitchen island we bought to resell.
The outboard accessible driver tool seems to make setting up the adapter and bits easier. Not sure if it makes enough difference to matter, in regard to inboard drivers, but it feels quicker when using it.

-
Nice one GLBM

-
The PAD does provide a nice range of options when it comes to drivers.

-

El día 21
Something tells me this is not going to work...


-
Use the pliers D_T

-
Actually, I love to save my fingernails and slide the driver under the pull-tab to lift it up.
I know you can do it, D_T!

-
Day 22
This morning I used the jeweler’s driver to
tighten a screw on my partners reading glasses
Now at least they sit on her face properly
No problems with using the jeweler’s driver




-
Handy size driver to have.

-
Works great

-
Thanks for the votes of confidence, lads

Meanwhile, on Day 22, the can opener finally got a go at three cans I found in my mum's larder and were a bit over the sell by date. I must say, after a little bit of getting used to it, it worked reasonably well. The angle of the cutting edge seems to indicate the opener should be operated around the can by pushing forwards in the clockwise direction (i.e. with the left hand) but the bulk of the handle bottom is in the way. Turns out anticlockwise with the right hand works too, somewhat less effective than theoretically possible because of the wrong skew, but OKish.

-
Nicely done D_T

-
D_T, I was looking closely at your can opener.
I think the factory grind on your opener was far superior to the grind on mine. Your can opener seems to have been ground in such a way as to give you a decent point on the tip. I had to regrind mine significantly to achieve that.
I'm amazed at the difference between our initial grinds. Glad yours is a worker!

My PAD must have been made Monday morning, after a long weekend. :'(
-
Thanks Wspeed

Agreed Nix, the point is pretty sharp and the forward edge halfway so, so I think I could easily improve it... -
My replacement Powerlock got delivered today.

Amanda at SOG was great to work with and I'm pleased with the swap.

The Powerlock is certainly a bit quirky and eccentric, but the quality is definitely a couple of steps above my, now-returned, PAD. Maybe I just got a lemon. I'll save specific thoughts for a Powerlock challenge.....starting tomorrow.

In the meantime, I'll follow along with you guys as you finish up this Access to Power challenge!

-
Nice one Nix looking good

-
+1 - great it got sorted out that quickly Nix! Enjoy

-
@Nix said:
My replacement Powerlock got delivered today.
Amanda at SOG was great to work with and I'm pleased with the swap.

The Powerlock is certainly a bit quirky and eccentric, but the quality is definitely a couple of steps above my, now-returned, PAD. Maybe I just got a lemon. I'll save specific thoughts for a Powerlock challenge.....starting tomorrow.

In the meantime, I'll follow along with you guys as you finish up this Access to Power challenge!

Awesome! They sent you the slightly slimmer version (newest). I like it a bit more than the older models for general carry. Enjoy it. One of the few tools made that is almost the same as when it first came out.
Day 22:
China cabinet and the old oak blues. The oak is lways warped and/or skewed around the door, because of heavy glass. Removed the door, squared it up, filed the burr off a screw, drilled holes for a catch, put the door back on, and installed the catch pin on the door. Now for boat loads of finish work. :ahhh


Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login