Access to Power -SOG 30-day Challenge! Starting June 1st! Access & Access Deluxe
-
Nice one GLBM

-
The PAD does provide a nice range of options when it comes to drivers.

-

El día 21
Something tells me this is not going to work...


-
Use the pliers D_T

-
Actually, I love to save my fingernails and slide the driver under the pull-tab to lift it up.
I know you can do it, D_T!

-
Day 22
This morning I used the jeweler’s driver to
tighten a screw on my partners reading glasses
Now at least they sit on her face properly
No problems with using the jeweler’s driver




-
Handy size driver to have.

-
Works great

-
Thanks for the votes of confidence, lads

Meanwhile, on Day 22, the can opener finally got a go at three cans I found in my mum's larder and were a bit over the sell by date. I must say, after a little bit of getting used to it, it worked reasonably well. The angle of the cutting edge seems to indicate the opener should be operated around the can by pushing forwards in the clockwise direction (i.e. with the left hand) but the bulk of the handle bottom is in the way. Turns out anticlockwise with the right hand works too, somewhat less effective than theoretically possible because of the wrong skew, but OKish.

-
Nicely done D_T

-
D_T, I was looking closely at your can opener.
I think the factory grind on your opener was far superior to the grind on mine. Your can opener seems to have been ground in such a way as to give you a decent point on the tip. I had to regrind mine significantly to achieve that.
I'm amazed at the difference between our initial grinds. Glad yours is a worker!

My PAD must have been made Monday morning, after a long weekend. :'(
-
Thanks Wspeed

Agreed Nix, the point is pretty sharp and the forward edge halfway so, so I think I could easily improve it... -
My replacement Powerlock got delivered today.

Amanda at SOG was great to work with and I'm pleased with the swap.

The Powerlock is certainly a bit quirky and eccentric, but the quality is definitely a couple of steps above my, now-returned, PAD. Maybe I just got a lemon. I'll save specific thoughts for a Powerlock challenge.....starting tomorrow.

In the meantime, I'll follow along with you guys as you finish up this Access to Power challenge!

-
Nice one Nix looking good

-
+1 - great it got sorted out that quickly Nix! Enjoy

-
@Nix said:
My replacement Powerlock got delivered today.
Amanda at SOG was great to work with and I'm pleased with the swap.

The Powerlock is certainly a bit quirky and eccentric, but the quality is definitely a couple of steps above my, now-returned, PAD. Maybe I just got a lemon. I'll save specific thoughts for a Powerlock challenge.....starting tomorrow.

In the meantime, I'll follow along with you guys as you finish up this Access to Power challenge!

Awesome! They sent you the slightly slimmer version (newest). I like it a bit more than the older models for general carry. Enjoy it. One of the few tools made that is almost the same as when it first came out.
Day 22:
China cabinet and the old oak blues. The oak is lways warped and/or skewed around the door, because of heavy glass. Removed the door, squared it up, filed the burr off a screw, drilled holes for a catch, put the door back on, and installed the catch pin on the door. Now for boat loads of finish work. :ahhh


-
Nice work GLBM

-
Thanks, guys!

-
great on the new PowerLock! I will say it's probably the multitool model that I have abused the most throughout the years (I've had 3, now just 1) and it took it like a Champ. I've dropped it from 20ft on concrete,
hammered on it with tools and wooden sticks :ahhh, stabbed and pried with the tips of the jaws and used it as a bludgeon on occasion 
Other than a few scratches, dents and bendung it's still like new and works flawlessly.

I removed the covers on all three but they are nice to have.
Yes the inner tools leave a bit to be desired but are sufficient and the jaws/pliers are the main attractive to this tool.One particular thing I've not heard anybody mention here is that the Compound Leverage is helpful in doubling the gripping force but also the opening force,
something that I've taken profit of when stabbing into drywall and then opening the tool to widen the hole, when prying things apart with the jaws, etc.It is an advantage that none other multi tool manufacturers can claim to have on their tools
, at the expense of having a wider arc of movement and plier handle separation when opening the jaws :P
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login