Powerlock 30-day challenge
-
Those wood handles you made.

My only wood-handle custom is so smurfed-looking I am almost too embarrassed to post it. It went well until I drilled the hole for a screw/nut and splintered it out in the center.
-
I was super careful with these.

-
The wood scales look amazing Nix. You did a great job on them.

-
Thanks, Alan!
It was a fun project. (Using scrap wood...
) 
-
Day 14 (continued):
Decided to share a piece of delicious chocolate with oranges and almonds with Mrs Nix this evening. Obviously, breaking it cleanly in half was fairly important.
I used the awl to score the chocolate bar in half (more or less) and then snap it cleanly. One of the awl uses Mrs Nix really appreciates.

-
I could soo do with some chocolate right about now.

-
**You **did those scales?!! :o :ahhh
not that I doubt your craftsmanship and handworking abilities but those look supreme :o and like an aftermarket custom scale option for people with $ and exquisite taste

-
Thanks, El P.

Yes; I made them from some scrap pieces of Maple.

-
Day 15:
I peened the scissors a bit more and today I got the chance to try 'em out. Plastic bags have been a real challenge for the scissors in the past. Today I'm soaking some beans, so the scissors had to meet it's nemesis.

At first it was a bit of a struggle, but then I realized that the scissors don't cut very well at the pivot point, but do cut fairly nicely closer to the tips. Once I realized that, I was able to make repetitive snips with the tip-half of the scissors and the bag was defeated.
A victory of sorts......
-
Good job Nix

Shame that the scissors still don’t work properly :ahhh
Maybe peen the Scissors again

-
I like the new Avatar, W!

There isn't much play in the scissors now. And the scissors are mostly functional for my purposes. I think I'm going to follow the old saw: "Better is the enemy of good."
I'm going to call these scissors "good enough" and not risk messing them up at this point.

If further use dictates that I peen them some more, I'll hazard that, but for right now.......best to leave well enough alone, I think.

-
Thanks Nix

You never know the scissors might get better with use
:D -
self sharpening scissors like Wenger's might :D
-
Day 16:
Not much going on today, but I did cut the lawn. Before hand, I touched up the mower's blade. The Powerlock's file actually did fairly well in tidying up the edge. After the file, I hit the mower blade with a diamond rod and then got to cutting.

Of course, after cutting the lawn on a hot summer day, a fella deserves to relax with some cold suds......Dutch_Tooler knows what I mean.....

-
Nice one Nix

Good to hear that the file worked better :D -
Back home now and no significant adventures. I was really happy to see there is still some snow lingering up on the peaks of the taller mountains. Snow is water, and water is life. So snow in July means water in the creeks and streams, and life in the rivers and lakes. And that puts a smile on my face.

I did struggle a bit with the scissors again. I'll try to peen them some more in the next day or two. Otherwise, the Powerlock just rode along for the journey. Awlways nice to have a multi close at hand.
Time for a G&T now, so......

One thing I miss about living in the mountains is seeing snow in the summer

-
Nice to see the file came through on the mower blades. The newer PL file isn't good, but it isn't bad like the PAD file either. The older "round end" file is a bit better, but for some reason, SOG has never made a "good" file. Their best files are mediocre to be honest.
You could order one of the older round files from the MT.o store. It would drop in without an issue. The older one has a bigger usable area for sure.
-
Day 17:
Messed around with testing the awl and Phillips driver today.
Used the awl to drill a pilot hole for a standard wood screw:

Awl did a fairly good job with this task.
Next I tried driving the wood screw into the 2x4:

I drove the screw about 1/2 way in. At that point, the resistance led to the driver twisting, flexing, and popping out of the screw head. I then used a standard 1pt Phillips screw driver to drive the screw in a bit further, but it, too, started popping out. I'd say the Powerlock's Phillips worked well as compared to a standard driver, although I did notice significant flexing of the blade in the handle and the handle in the frame, all of which led to the driver tip disengaging from the screw. i.e. 'popping out'.
Lastly, I used the Powerlock to remove the screw from the 2x4. This was fairly tough, but the Powerlock did well and accomplished the job.

The driver tip did get chewed up a bit, but still looks entirely functional. I don't think it would be happy with repeated hard use like this, but it accomplished what I set out to test.
-
That didn’t work to well :ahhh :ahhh
It should be able to work
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
