Can Opener Comparison
-
Wenger Highlander
Great round shape to hold on to. The can opener is pointy and sharp, and it did not slip off.
It did get stuck and folded a bit when trying to get it out. The cut was clean, but I had to be mindful of the angle I was on, to prevent it from jamming.2 points for punching through.
2 for comfort.
0 for not jamming.
1 for cutting.
2 for not slipping.
Total: 7

BuckTool
Barely able to hook onto the rim, due to bad placement. It was a chore to keep it on the rim, and impossible to cut consistently. Very jagged cut, creating burrs and sharp edges.
I might as well have used a blade, Phillips, or flathead, with arguably better results. At least it locks, so no jamming.1 point for punching through.
0 for comfort.
2 for not jamming.
0 for cutting.
0 for not slipping.
Total: 3

Schrade USA Tough Tool
One handle has to be unfolded, otherwise it is impossible to use. It kept jamming and folding. Very poor cutting as well.2 points for punching through.
1 for comfort.
0 for not jamming.
0 for cutting.
1 for not slipping.
Total: 4

Core, Buck, and Schrade. Look how far to the wrong side the Buck can opener is.

-
Bear Jaws
Locking, sharp, great. No jamming, no slipping. The cut is a bit rougher that other claw can openers. Its levers for unlocking protrude a bit. Not a bad choice at all.2 points for punching through.
1 for comfort.
2 for not jamming.
1 for cutting.
2 for not slipping.
Total: 8

Craftright (Generic Suspension clone)
The piercing point is extremely blunt, and as such did not punch through easily. Clean cut, did not jam, did not slip off. The handle edges are not that rounded off, but not all that bad, once you get it to pierce.0 points for punching through.
1 for comfort.
2 for not jamming.
2 for cutting.
2 for not slipping.
Total: 7

Spirit
Great ergonomics, and it is very sharp, quite a similar experience as with a sak. Now with the additional benefit of a locking can opener, though I did tend to slip off. But that's just me.2 points for punching through.
2 for comfort.
2 for not jamming.
2 for cutting.
1 for not slipping.
Total: 9

-
Coast
0 points for punching through. The piercing point is blunt and its hook kept coming off the rim.
2 for comfort. Very well rounded off edges.
2 for not jamming.
0 for cutting. Once you go too far away from the rim, you cannot continue the same cut. And it does not punch through easily to start a new one.
0 for not slipping.
Total: 4

SOG PPP
Quite good. I did not slip off the rim, and it never jammed. The plier gears dig into my hand, and the cut was a lot more jagged that other quarter-circle can openers.2 points for punching through.
1 for comfort.
2 for not jamming.
1 for cutting.
2 for not slipping.
Total: 8

Mini-Tool
An oddball design. It does not slip or jam, and cuts easily and cleanly. The only issue is the design itself. Being integral to the handle extension, it unfolds at the wrong orientation. When pressing downwards to cut into the can, you are pressing in the same direction the can opener folds back into the handle. If you do not exert force to keep it open, it will simply fold back. The piercing point is blunt, and took some effort to punch through, while fighting it from folding. Once through, everything else was great.0 points for punching through.
2 for comfort.
2 for not jamming.
2 for cutting.
2 for not slipping.
Total: 8

Juice
0 points for punching through. The piercing point is blunt and not at the best angle to punch through.
1 for comfort. The edges dig into my hands, and so does the corkscrew. This is the old design, so maybe now it's better?
2 for not jamming.
2 for cutting.
2 for not slipping.
Total: 7

-

From best to worst:
10: Core
9: Charge
9: SwissChamp
9: Deluxe Tinker
9: MP400
9: Ganzo G302
9: Spirit
8: Bear Jaws
8: Mini-Tool
8: SOG PPP
7: Wenger
7: Craftright
7: Juice
6: Roxon Storm (modded)
4: Schrade
4: Coast
3: BuckTool
0: Roxon Storm
Thoughts
I prefer claw can openers the most. Especially when done right, like Leatherman, Bear and Son, and Ganzo. I get a consistent cut, and I never slip off the rim. Non-locking claws tend to get stuck, like Wenger and Schrade. I am not fond of this. I do not really care about the time needed to get it free, but it just makes the whole process frustrating.
With quarter-circles, I tend to slip off the rim, but the Victorinox ones are great, and the others are mostly good enough. And none jammed, though I'd probably mangle the can with the Coast.
Some can openers performed better than I expected. The cheap Craftright was very reluctant to punch through, being extremely blunt, but cut very easily. So did the Juice and Mini-Tool. I hoped the Wenger would do better, but it is an old example, which was purchased used. Maybe if it was new, the backsprings would be stronger and help it jam less.
I was surprised with how poor a cutter the Schrade was, and how terrible in general the BuckTool was. As for the Storm, I was extremely disappointed that it could not even hook on the rim. After I modded it, even with it being average, I am very pleased that at least it can now open a can at all.
I will use these different can openers instead of the Core, and perhaps revisit a score or two. My technique with quarter-circles could improve. A Wenger sak in better shape may do better than the beat up one I used. A Victorinox delemont sak might be better in the hand than the SwissChamp or Tinker. I did not use one can per can opener, so going full circle may change a thing or two.
I am interested to know what people use, if anything. I know some people swear by Victorinox, but others, like me I guess, prefer a Leatherman claw. Do you get a consistent cut with a sak? Do you slip off the rim with quarter-circles? Does your Wenger get stuck?
-

Very cool!
-
Excellent write up RP

Nice to see all the results of the can openersI like the SAK can opener the best

-
Good tests, it was fun going through each tool.

I've found that SOG Can openers leve really jagged cuts and that Wengers tend to get stuck a lot (I've used 4 different ones so far from Wenger, but all got stuck too often :ahhh)I am also very fond of my Blast and Fuse can openers, so I agree with you on certain points

-
Amazing work, RP! Thank you!

-
Great write-up, RP!
Thanks! 
I've used the Vic can opener the most, so it's the one I prefer. I'm jaded by experience. As a bonus, the Vic can opener can be used as a small driver/Phillips driver or light pry tool. So....I'd give the Vic can opener an extra point for 'Versatility' and call it a draw with the Core. :D
-
Oh, and I seem to encounter a lot of cans that need can openers: beans, tomatoes, tuna, etc.....
-
Thanks guys!

I'll get more cans and test some tools and either confirm their score or change a thing or two.
Not yet tested some tools:Surge, Rebar, SuperTool 200. Locking Leatherman claws. Probably just as good as the Core.
PST, Sideclip, Wingman. Non-locking Leatherman claws. I wonder if they'll get stuck.
Safari Hunter, Bantam. Victorinox combo tools. Will they be as good as their classic quarter-circle?
Victorinox 84, 93, 111, 130mm models. Classic quarter-circle, so probably the same performance as the Deluxe Tinker.
Wenger 120mm and 130mm. Still not locking, but they might be better than their 85mm model claw.
PowerLock, probably the same as the PPP. -
@ReamerPunch said:
Thanks guys!
I'll get more cans and test some tools and either confirm their score or change a thing or two.
Not yet tested some tools:Surge, Rebar, SuperTool 200. Locking Leatherman claws. Probably just as good as the Core.
PST, Sideclip, Wingman. Non-locking Leatherman claws. I wonder if they'll get stuck.
Safari Hunter, Bantam. Victorinox combo tools. Will they be as good as their classic quarter-circle?
Victorinox 84, 93, 111, 130mm models. Classic quarter-circle, so probably the same performance as the Deluxe Tinker.
Wenger 120mm and 130mm. Still not locking, but they might be better than their 85mm model claw.
PowerLock, probably the same as the PPP.IME the Wingman one sucks, :P but could be my technique :ahhh
the Combo tool works wonders on my Wenger Entree (due to its thinness guess
) but not so good on my Vics ???
PL is the same as the PPP, ergos of the handles apart, at least in my testing.
-
Look forward to you testing more can openers RP

-
@ReamerPunch said:
Core, Buck, and Schrade. Look how far to the wrong side the Buck can opener is.

Looking at this again, I may use the BuckTool left-handed.
-

Our next contestants are all claws. Leatherman Rebar and Wingman, Victorinox Safari Hunter, Wenger 06 - Mountaineer, and last, and possibly least, the Workpro 10 in 1.


-
Leatherman Rebar
Not only a perfect 10, but even better than the Core. The Rebar, Charge, Core, and a few others have the same can opener, but the Rebar excels in ergonomics. Nothing protrudes to dig into my palm, and it is not as squared and bulky as the Core. Moving the body up and down with ease, the edge advanced beautifully through the can top. Perfection.2 points for punching through.
2 for comfort.
2 for not jamming.
2 for cutting.
2 for not slipping.
Total: 10

Leatherman Wingman
This is not identical to the locking can opener found in the Core, Charge, etc. It is a different design, though still very capable. The can opener sits a bit more to the right than on the Rebar, so to compensate, they made the implement longer, distancing the hook from the handle. Unfortunately, its edge meets the can top at a more obtuse angle, and is shorter, limiting the length of each individual cut. Good edge and properly sharpened, with a good piercing point. Not as straight forward as the Core/Rebar. I had to adjust my grip and be mindful of where the cutting edge was going. There are also some edges that could be more rounded. Still, a clean cut with no sharp edges. A great choice.2 points for punching through.
1 for comfort.
2 for not jamming.
2 for cutting.
2 for not slipping.
Total: 9

Victorinox Safari Hunter
This looks more like a good bottle opener and less like a combination bottle and can opener. No typical can opener edge grind, no acute piercing point either. I was surprised with how easily it punched through the top, and it felt great in the hand. Being at the tip of a saw, the can opener sits the farthest away from the body than any other can opener. This may have helped leverage, and in conjunction with a good hook to help it stay on the can rim, the affair was quite comfortable. At no point did I feel like the saw edge would mess up my evening. The downside is that, since there is no edge like on other claw can openers, this is more of a bender than a cutter, and as such, it left a messy cut, with sharp points and edges.2 points for punching through.
2 for comfort.
2 for not jamming.
1 for cutting.
2 for not slipping.
Total: 9

-
**Wenger Ranger 06 - Mountaineer **
The same can opener as on the 85mm Wenger models. A larger handle to hold on to, but with a massive blade spine digging into my fingers. This appeared to cut better than the Highlander, though it still jammed when cutting, and folded when being freed.2 points for punching through.
1 for comfort.
0 for not jamming.
2 for cutting.
2 for not slipping.
Total: 7

Workpro 10 in 1
The tiniest can opener so far. Non-locking, one third the edge of other claws, and rather blunt. Piercing was not easy, nor was anything else. This is the smallest multi-tool to hold while opening a can. Being blunt, it did not punch through easily. In order to get it to cut and to get a better grip, I had to support the can opener with my thumb. It does not cut well, constantly slipping off the rim, and having a very short and blunt cutting edge. Moving at a snail's pace, my thumb got numb for little reward. If you are unfortunate enough to have this to open a can, be patient and hope that, by the time you're done, your food is still within expiration date.1 points for punching through.
0 for comfort.
2 for not jamming.
0 for cutting.
0 for not slipping.
Total: 3

This is the same size as the Mini-Tool, but their can openers are not. I also supported the Mini-Tool's can opener with my thumb, but it is a wide handle, and thus very comfortable, while also providing a good grip and leverage.


-

Today's contestants are quite a diverse lot.
Leatherman SuperTool 200 and PST, Victorinox Bantam, SOG PowerLock, Wenger RangerGrip 60, and Sheffield 10 in 1.


-
Leatherman SuperTool 200
Not exactly the same design with the Core, but functionally identical. Nicely rounded handles with nothing to dig into my hand. It did not jam, it did not slip. Clean, easy cut with nothing to worry about.2 points for punching through.
2 for comfort.
2 for not jamming.
2 for cutting.
2 for not slipping.
Total: 10

Leatherman PST
Nice compact tool to hold on to, with a great claw to cut into the can, this is just as good as its locking brethren. Very comfortable in the hand, consistent cut with no sharp edges left behind, no slipping off the can, no jamming.2 points for punching through.
2 for comfort.
2 for not jamming.
2 for cutting.
2 for not slipping.
Total: 10

Wenger RangerGrip 60
I expected no difference between this and the other Wenger can openers, and yet, here we are. Great cut, clean and easy, with no sharp edges left behind. Curiously, it did not get stuck while cutting, because I was mindful of how deep I pushed the claw in the can. Taking a closer look, you will notice that this is differently designed than a typical Leatherman claw.
On the Leatherman claw, the edge is in a continuous line with the 'mouth', for lack of a better term. From the tip of the claw, to the tip of the hook, it is one curvy line.
On the Wenger, there is a harpoon element to it, as the edge sits below the 'mouth'. As the edge ends, there is almost a barb, acting similarly to a fish hook barb. If you push the claw too deep into the can, the barb passes the top of the can and interferes with retracting the claw. I hope this makes sense.

Being careful not to let the barb sink in the top of the can, I was able to cut consistently, without getting stuck, not even once. Eliminating the tendancy to jam into the can top, the only issue was the blade spine digging into my hand.
This effectively means that I have to test the 85mm and 120mm models again, and see how well they can do.2 points for punching through.
1 for comfort.
2 for not jamming.
2 for cutting.
2 for not slipping.
Total: 9

-
this is really extensive. thanks for the comparison. personally I feel more intuitive with SAK style can openers than with LM/Wenger style, but they all work. I wonder how you'd rank the openers on Bantam or Hunter
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login