a couple wave problems
-
Does serrated blade sway when its open? If it does problem may just be loose screws, it affects on handle too if screws are too loose
Only Tools Matters
-
@Antti Lammi said:
Does serrated blade sway when its open? If it does problem may just be loose screws, it affects on handle too if screws are too loose
Only Tools Matters
No, the outside tools on the "good" handle have the same tension as the bad handle. Also, here's another picture
It looks excelent condition, i dont see anything what can cause problem. On my Wave, blade/file handle slides on also and very end when opening it makes little bumb and its then bottom. Handle doesnt open when opening pliers.
Only Tools Matters
-
@Antti Lammi said:
@Antti Lammi said:
Does serrated blade sway when its open? If it does problem may just be loose screws, it affects on handle too if screws are too loose
Only Tools Matters
No, the outside tools on the "good" handle have the same tension as the bad handle. Also, here's another picture
It looks excelent condition, i dont see anything what can cause problem. On my Wave, blade/file handle slides on also and very end when opening it makes little bumb and its then bottom. Handle doesnt open when opening pliers.
Only Tools Matters
Yeah the blade/file handle snaps into place like that, the serrated/saw handle just slides in and out, there's barely any friction. It's all cleaned out and the one handle is still loose. Both sides look identical to one another
-
I wonder, like Gerleathingy already suggested, if the side of the handle has bow'd a bit and just needs a little bit of a tap to push it flat again... not too much though, remember Father Ted...

-
@Fuzzbucket said:
I wonder, like Gerleathingy already suggested, if the side of the handle has bow'd a bit and just needs a little bit of a tap to push it flat again... not too much though, remember Father Ted...Gerleathingy?

-
Seems strange that this only happened after a clean though...

-
It is strange for sure.
The only conceivable idea I had left was a little piece of metal had possibly gotten caught in there and he opened the pliers very fast and it bulged the frame channel. And the cleaning washed the piece of metal debris out.
Other than that, I have no more ideas.
The solutions, for that, have been covered though. :ahhh
-
Thanks for the tips everyone, not sure if I'll warranty it or just live with it.
-
@Fuzzbucket said:
I wonder, like Gerleathingy already suggested, if the side of the handle has bow'd a bit and just needs a little bit of a tap to push it flat again... not too much though, remember Father Ted...I agree with Fuzzbucket and Gerleathingy, and think this is the main issue.

There is a bit of a gap (in red) where the handle has bowed out. You can see that this allows the prong (that locks the blade) shut to rise up a little. But I don't think the issue is with the prong (I assume the serrated blade locks into closed position when the handles are open).
If this were my Wave I would take a flat end screw driver and hammer, and give the handle a good tap
(as indicated on green). I did this to my Wave just now, as one handle is does not 'click' into open position as good as the other handle does (but it's not too bad). Actually, it made no difference. ??? But maybe I need to hit it harder

Waves are not impossible to take apart, so if the pliers head were removed from the handle I think it would be easier to bend/bash the handle into position.
I DO NOT RECOMMEND YOU DO ANY OF THE ABOVE TO YOUR WAVE.
As for the gritty inner tools, I had a second hand (almost unused) Charge with gritty tools. A bit of oil and a fair bit of opening/closing soon had that solved.
PS: We once had an old electric kettle in a shared common room, and one day I cleaned it out as it was full of gunk and limescale. After that, it leaked badly, and we had to get a new one. It was the gunk and limescale that was holding the kettle together....
-
I noticed that my waves handle was broken and thats why it doesnt click when opening it. You should also check is it in goid condition in didnt noticed crack until i looked carefully when openin handle i noticed crack in my Waves handle

Only Tools Matters
-
I just took my (0704) Wave apart (again) and did the
on the loose handle --- it did tighten up the click/lock as pliers head is deployed.BUT, after seeing the damage to Antti Lammi's Wave, I was a bit worried about hitting this part of the Wave.
While I was at it, I used my Squirt to squeeze together the inside edges of the Wave --- the part with the ruler marks. If you do this at the pliers end, it stops the Wave handles being a bit floppy when shut. (Although, I suppose if you want One Hand Opening, and want to flick the pliers open, you want to do the opposite?)
-
Theres danger when bashing waves handle, be careful when tempering with those. Best way to repair it is sending it to warranty.
Only tools matters
-
So have you received your wave back yet
Only Tools Matters
-
Great to hear they got you fixed up with another

-
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
