a couple wave problems
-
By looking that picture theres seems to be dirt what prevents mechanism work correctly. Try clean with pressure air, spraying cleaner or with running water.

Only Tools Matters
-
I just did a quick forum search and couldn't find an answer to this.. I just gave my wave a cleaning and oiling and now the serrated blade handle doesn't "click" into place when the pliers are open it just slides in and out of place with little force.
Put the serrated blade back into the handle when the pliers are closed?

Oops, I missed seeing the word "handle". Now I understand.

That will teach me to MTO late at night.
-
I agree with Antti
, there's a lot of crud around the forked thingies and cleaning that would be my first port of call. -
I may be misunderstanding what is being conveyed here about the dirt in the pivot, so set me straight if I misunderstood.
On the Wave, those prongs don't act as plier locks. They are just to lock the PE and SE blades closed when the pliers are engaged. The plier locking is done via the edge of the ramps, cast into the pliers, against the inside of he handle channel.
One of the handle channels looks as if it were "bowed" outwards. This would cause the lock ramp not to have pressure when the pliers are engaged.
This can happen if a foreign object, such as a piece of metal, got lodged between the ramp and handle channel.Edit: Once the possible foreign object was removed, there was a gap left, with the handle channel bowed out.
-
I'm just saying lets clean the area first. Perhaps the dirt is forcing the prongs to get in the way.

-
So did anything helped, if not could you take pic inside (like above) so we could see is there any abnormality. Pic inside that side what is not working properly

Only Tools Matters
-
Does serrated blade sway when its open? If it does problem may just be loose screws, it affects on handle too if screws are too loose
Only Tools Matters
-
@Antti Lammi said:
Does serrated blade sway when its open? If it does problem may just be loose screws, it affects on handle too if screws are too loose
Only Tools Matters
No, the outside tools on the "good" handle have the same tension as the bad handle. Also, here's another picture
It looks excelent condition, i dont see anything what can cause problem. On my Wave, blade/file handle slides on also and very end when opening it makes little bumb and its then bottom. Handle doesnt open when opening pliers.
Only Tools Matters
-
@Antti Lammi said:
@Antti Lammi said:
Does serrated blade sway when its open? If it does problem may just be loose screws, it affects on handle too if screws are too loose
Only Tools Matters
No, the outside tools on the "good" handle have the same tension as the bad handle. Also, here's another picture
It looks excelent condition, i dont see anything what can cause problem. On my Wave, blade/file handle slides on also and very end when opening it makes little bumb and its then bottom. Handle doesnt open when opening pliers.
Only Tools Matters
Yeah the blade/file handle snaps into place like that, the serrated/saw handle just slides in and out, there's barely any friction. It's all cleaned out and the one handle is still loose. Both sides look identical to one another
-
I wonder, like Gerleathingy already suggested, if the side of the handle has bow'd a bit and just needs a little bit of a tap to push it flat again... not too much though, remember Father Ted...

-
@Fuzzbucket said:
I wonder, like Gerleathingy already suggested, if the side of the handle has bow'd a bit and just needs a little bit of a tap to push it flat again... not too much though, remember Father Ted...Gerleathingy?

-
Seems strange that this only happened after a clean though...

-
It is strange for sure.
The only conceivable idea I had left was a little piece of metal had possibly gotten caught in there and he opened the pliers very fast and it bulged the frame channel. And the cleaning washed the piece of metal debris out.
Other than that, I have no more ideas.
The solutions, for that, have been covered though. :ahhh
-
Thanks for the tips everyone, not sure if I'll warranty it or just live with it.
-
@Fuzzbucket said:
I wonder, like Gerleathingy already suggested, if the side of the handle has bow'd a bit and just needs a little bit of a tap to push it flat again... not too much though, remember Father Ted...I agree with Fuzzbucket and Gerleathingy, and think this is the main issue.

There is a bit of a gap (in red) where the handle has bowed out. You can see that this allows the prong (that locks the blade) shut to rise up a little. But I don't think the issue is with the prong (I assume the serrated blade locks into closed position when the handles are open).
If this were my Wave I would take a flat end screw driver and hammer, and give the handle a good tap
(as indicated on green). I did this to my Wave just now, as one handle is does not 'click' into open position as good as the other handle does (but it's not too bad). Actually, it made no difference. ??? But maybe I need to hit it harder

Waves are not impossible to take apart, so if the pliers head were removed from the handle I think it would be easier to bend/bash the handle into position.
I DO NOT RECOMMEND YOU DO ANY OF THE ABOVE TO YOUR WAVE.
As for the gritty inner tools, I had a second hand (almost unused) Charge with gritty tools. A bit of oil and a fair bit of opening/closing soon had that solved.
PS: We once had an old electric kettle in a shared common room, and one day I cleaned it out as it was full of gunk and limescale. After that, it leaked badly, and we had to get a new one. It was the gunk and limescale that was holding the kettle together....
-
I noticed that my waves handle was broken and thats why it doesnt click when opening it. You should also check is it in goid condition in didnt noticed crack until i looked carefully when openin handle i noticed crack in my Waves handle

Only Tools Matters
-
I just took my (0704) Wave apart (again) and did the
on the loose handle --- it did tighten up the click/lock as pliers head is deployed.BUT, after seeing the damage to Antti Lammi's Wave, I was a bit worried about hitting this part of the Wave.
While I was at it, I used my Squirt to squeeze together the inside edges of the Wave --- the part with the ruler marks. If you do this at the pliers end, it stops the Wave handles being a bit floppy when shut. (Although, I suppose if you want One Hand Opening, and want to flick the pliers open, you want to do the opposite?)
-
Theres danger when bashing waves handle, be careful when tempering with those. Best way to repair it is sending it to warranty.
Only tools matters
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

