KutMaster Multi-tools.
-
The knock off manufacturers certainly doesnt care I believe. Their QC are probably just visual, if it looks like a tool, it will pass the test. Not all manufacturers but most I believe, if they even have a QC dept. Sadly, that's the impression that these tools have on people. Of course they are decent or even good ones but they are rare. Honestly, I am pleasantly surprised by your test that half of them are good. Those are gold, keep them well. Most of us do use our tools, there are just go-tos tools for different task. Cutting hard or solid core wire, most cutters works , even cheap ones. If I know I need to cut copper stranded, a cheap knock off will be the last thing I will grab.
-
Okay, I sent an email to Kutmaster complaining that the Wrench Head doesn't... you know... kut any wires. With a name like Kutmaster, I argued, it should be able to cut things. Got a response back saying that was a special run and no longer produced, and that he would send me a USA-made Multimaster free of charge. And made it clear that it was a $69.99 value. (lol, they're $28 on eBay). I received the Multimaster today, in a plain white box with a sheath and a selection of bits... with one bit missing from the holder. First off, it appears to be a used unit. There is some gunk in the teeth of the jaws, some wear from the pivoting jaw against the side plates, and some more gunk attached to the magnet in the bitdriver. My Wrench Head was brand new and had no gunk anywhere. The tool is also recently oiled and sharpened. The pivot screw is shiny plated steel, and of a different type than the normal flat-topped phillips. There's wear on the handle and around the nail nicks above the Multimaster logo. The big deal is that the tool is BENT. The bit driver was obviously torqued more than the tool could handle, and there is a bend in it. The top handle doesn't sit square with the rest of the tool body.
Unfortunately, the Multimaster's cutters are even worse than the Wrench Head's. The Wrench Head I was actually able to save. I took a small file and very lightly attacked the cutter until it was able to cut wires. Not everything, not always in one cut, but they did work passably. The Multimaster has different jaws, and the cutters are machined differently. The Wrench Head there is very little surface available to file before the cutter would become useless due to no longer overlapping. With the Multimaster there's plenty of cutter overlap... the problem is there is just a lot more play in the jaws. Not even play, really.. If I push the top jaw and bottom jaw sideways apart from each other (bottom jaw left, top jaw right), the frame of the tool flexes. I think this flexing is what's causing the cutters to be so bad. I tried filing an edge onto the Multimaster cutters, and they still can't cut anything.
First photo shows the bend. Second photo shows scratches above the "E" in "Multimaster", and on the handle above the "ST". Last pic shows the jaws, the wear (shiny spot surrounded by oil residue), and the non-standard pivot screw.
Charles.



-
Update: I sent the guy photos of the bent tool, and he gave me a WTF :) He's sending me a replacement right away. So that's nice. Also, looking at packaging for the multimaster, it apparently comes with 5 bits and a 6-bit holder, so I wasn't missing a bit.
I don't know whether there are quality control issues with Kutmaster or what's going on really. I do know that they're bending over backwards to make me happy, and that's worth a lot in my book.
Charles.
-
Hey, I just found a "Mountain Quest" branded version of the Multimaster on eBay. It's not my thing, but if you need it for your collection, the link is here: https://www.ebay.com/itm/Mountain-Quest-Multi-Tool-w-Bits-and-Sheath-Pre-Owned/113102975834
Charles.
-
Today I picked up a new version of this tool, the "Winchester Torquemaster".
This tool is a bit of a hybrid between the Multimaster and the Wrench Head. First off, it has all the tools of the Multimaster. The tool channel is wider than the wrench head. It has the same standard nut cutouts in the handle, and the same T-handle bitdriver configuration as the Wrench Head. BUT... look at the rivets on the tool. It has a two-piece jaw like the Multimaster! This is a stronger, more robust jaw design, which also opens larger. The wire cutters, like all of the cutters on these tools, are abysmally bad. There is almost no overlap, less than 1mm. For side cutters to work, there needs to be overlap, and this is just poorly implemented.
The tools are also a mixed bag. The blade is smaller and shorter than the one in the Wrench Head. It's also not very sharp, where the Wrench Head was sharp enough to cut receipt paper. The file is good, it can file mild steel without damage. The Wrench Head shows wear quickly when filing steel. BUT, the Wrench head's file doubles as a gasket scraper. So it's arguably more useful. The saw is a stand out tool, making short work of a small oak branch. It's only got one layer of teeth, but it still does a most excellent job.
So, a mixed bag here. I'm really looking for one of these T-handle tools with two-piece jaws and good cutters, but I don't think I'm ever going to find that. :/
Charles.

-
Interesting tool there, Charles!

I do like the double-rivet jaw on it, but everything else screams China Kutmaster variant. :ahhh
Did you ever receive the replacement U.S.A MultiMaster that wasn't used/bent?
I just ordered an older MultiMaster, with the brand/model actually stamped into the handle, instead of silkscreen ink. Can't wait to compare it to my newer MMs. :)
-
No and the guy stopped responding to my emails. Ah well.
It is made in China, but apart from the cutters not working its a great tool. I’ve given up on cutters that work on these tools. They didn’t work on that bent up multimaster either. Coast got wire cutters right with their 2 piece pliers, but the wrench head and variants has a t handle bit driver which is absolutely amazing.
So what I’m doing is sliding an ES4 into the little pouch for the sockets in the wrench head sheath. That will handle any wire cutting and stripping duties that the kutmaster can’t handle.
Also, for my uses I’ve removed the serrated blade from the Winchester tool and added the feeler gauge and awl from the wrench head. Actually I also swapped in the main blade and combo file/gasket scraper from the wrench head too. The scraper is useful to me, even though the Winchester has a better file.
Because the Winchester is wider, I was able to remove the very thick serrated blade and swap in the very thin feeler gauge and medium width awl just by leaving out a couple washers. So I have one extra tool in my modded Winchester.
I’ve stuck a flashlight in the case, an extra row of Allen bits, and the ES4. It now lives under the seat of my motorcycle along with a set of spare brake and clutch levers, a cable lock, and a bungee net.
Charles.
Charles.
-
I tried the cutters on both of my MMs. I started with bamboo skewers and made 20 cuts on each tool. Then checked the cutters with 18-2 stranded wire. The BN version cut the wire before the skewer cuts, but had trouble afterwards. A little tightening of the pivot screw solved the problem and it now cuts fine. The NN version cut the wire before and after the skewer cuts, without tightening the pivot.
The bent handles may cause the cutters to not bypass properly. I would try emailing the guy everyday until he resonds. He promised a functioning tool and shoudl deliver. IMO of course.
As far as the Winchester. Glad you found a setup that works for you! The ES4 is fantastic.

-
Interesting tool
and cool that they sent you a new one from the company
to bad that the QC isn't there though 
-
I think Charles may have received a factory second MultiMaster. :-\
Marks on plier head from movement and a bent handle. Sounds like a classic factory second. :ahhh
-
Bringing up this thread again. Has anyone else seen the Garrity hammer tool? It appears to have a full tool load and door that matches the Kutmaster Multimaster. There are several of these on eBay right now around the $20 mark.
Charles.
.jpg)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login