EDC steel preference.....?
-
No real preference here. I have knives that have a variety of blade materials (1095, 420HC, whatever it is that Vic uses, S30V, S35VN, N690Co ...) and can't really tell the difference if they're sharp. I appreciate the ease with which you can sharpen Vic knives, love the look of a well used 1095 blade and like the toughness and edge holding of the super steels.
-
I value ease of sharpening and corrosion resistance the most,

then toughness and ease of maintenance (non-chippy, non-bendy, non-corrosive and non-brittle) ::)edge retention is not high on my property list, and price is important too (expensive is avoided, inexpensive is better to me)

My
ones. AUS8, H1, CTS-BD1, 420HC, 440B, 9Cr14MoV, 14C28N, 4116 Krupp, and most Sandvik steels, and also CTS-XHP and S30V
I avoid, generally: D2, 1065-75-95 series, M4, S90V, M390, and most CPM steels, 5Cr and 3Cr, 440C, AUS6want to try: Vanax and LC200N
I guess that's it :)
-
I voted no real preference, which is usually the case except when it comes to paddling/work where i use H1 as its low maintenance and can be left without washing and won't rust.
-
I couldn’t really vote. I carry a s110V for urban needs because I know I have access and time to sharpen properly. But if I know the situation will change otherwise then I’ll use AUS8, 1095, etc.
But I’ll admit the s110v was a recent change for me. I may go back to using mid tier steels as I truly believed those steels are ideal for edc as a great balance for sharpening ease, corrosion resistance, etc.
-
Stainless. Patina = dirt. :D
-
Being an enthusiast I have no problem carrying and using anything from 420HC to s35vn to laminated HAP40.
But given the choice I usually go for something in a good stainless like s30v or a super steel like CTS-204P
-
I voted semi stainless even though some of those steels listed are more stain less than the stainless listed.
Stainless is my preference by far but only the newer steels. It does not have to be the latest greatest
but steels like 420hc and SAK, I do not use anymore.Steels from AUS-8 to s90v if i like the knife I'll buy the steel but I won't buy the knife for the steel.
Like shark, given a choice i prefer a better steel.
-
I'm definitely willing to pay a little more to get a 154cm blade on a multitool. Bob Loveless was right: 154cm makes a nice knife blade.

-
Most blades I carry/use are 420HC and 440C stainless (I won't be upset if I leave cheap knife laying around and it goes missing). I sweat a lot(kind of sweat that drips from pants and shirt, then leaves white marks of salt) and non-stainless blades get spotty and pitted in a day or two on my belt or in my pocket. I would have to oil a non-stainless blade several times a day. Can't be bothered. :ahhh
Stainless blades will spot up on my as well, but it takes a week or two, then being stainless, it is easy to clean off the surface spots. :)
I like carbon steel patina, but I just can't carry them. I have several carbon steel knives, but they sit clean and spot free in the collections. :)
-
I've always found it interesting that even the most snobby of knife steel aficionados carry SAKs. I have no issue keeping my "higher end" steels sharp as others tend to bring up when talking about steels. That out the way, I like the "higher end" steels and many carbon steels as well. I've got a good variety I think but I'd like to try a few others like 3V, 10V, Elmax, and some of the interesting steels Spyderco uses.
Lets start with Vic steel. I have no issues. Razor sharp and performs each and every time. Even the most snobby of knife snobs carry a SAK from what I can see and read.
Steels on my MT, fixed blades, and folders. My S30V MT blade and Spyderco Native, 154CM MT and folder, ZDP189 Sypderco which I like very much, 01, A2, 1095, and
, oh and M390. I like them all. Does LMs 420HC work? Of course it does. I don't carry a stone or ceramic rods with my for work. I also dont carry them for my off days. I've had days where I've dulled my Vic blade and LM Wave blade. Did they still cut? Yes but when I can get more performance out of a higher end steel then why not? -
I would say I'm rather obsessed with steel, but what I play with and what I carry are 2 different matters.
What I've established is 8Cr13 is not good enough for me, but H1 is.
I have no doubt all the other fascinating steels are more than adequate, I just don't have the budget. My only concern with some is sharpening, but I have no experience.
I 100% prefer carbon/tool steels, but for something I can carry in my pocket, rinse under the tap and throw back in my pocket without worrying about rust in unseen places is pretty good.
Voted for first option for the sake of H1, #2 is also good for me.
-
I'm sure most of you have seen this.......I need some M390 in my life :facepalm:
-
@gerleatherberman said:
I sweat a lot(kind of sweat that drips from pants and shirt, then leaves white marks of salt) and non-stainless blades get spotty and pitted in a day or two on my belt or in my pocket. I would have to oil a non-stainless blade several times a day. Can't be bothered. :ahhhStainless blades will spot up on my as well, but it takes a week or two, then being stainless, it is easy to clean off the surface spots. :)
being in a similar situation as you, GLBM; I wholeheartedly recommend you trying out an H1 blade,

any of them, preferably in Serrated Edge 8)It was an eye opener for me

-
While I dont have H1 everything I've read about this steel and others experiences I agree with TP. Might be a good test of this steel GLBM. If I had one I'd send it your way for you to test.
-
I keep all my knives sharp, from low end 420 to super steels, and they all perform when I need to cut something. I am not a power user that cuts stuff 100 times a day anyway. My preference goes to stainless, though I have a few that take a patina, like this K390.

-
I like my 154cm. Great balance of all the advantages of different metals.
-
I like most steels
I really dont have any of the super steels but I do love H1
it is just about maintenance free except for the sharpening part :D I have a PE blade and keep it sharp by just stropping with leather and a polishing compound
Other than that I will use just about any steel, even carbon with a patina ::) :D -
@CallsignBadger said:
I like my 154cm. Great balance of all the advantages of different metals.154CM is a very nice upgrade, thats still easy to sharpen.
-
I carried a Wave standard version 2 for years, sure the 420 blade gets dull quick but all I'm doing is busting tape , cutting into AV equipment packages so no biggie.
I find a Charge Ti with 154 and I'm loving it . Use it hard for bout 4 years now. I have little chips all up and down the blade and i was being a dumbass and broke the very tip off. Used it as a flathead in a pinch for a bit
That 154 would bite me quite a bit being super sharp. :o :oNow I'm back to a Wave Plus with 420HC which will keep me going until my Ti is back from getting some work.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login