EDC steel preference.....?
-
I voted semi stainless even though some of those steels listed are more stain less than the stainless listed.
Stainless is my preference by far but only the newer steels. It does not have to be the latest greatest
but steels like 420hc and SAK, I do not use anymore.Steels from AUS-8 to s90v if i like the knife I'll buy the steel but I won't buy the knife for the steel.
Like shark, given a choice i prefer a better steel.
-
I'm definitely willing to pay a little more to get a 154cm blade on a multitool. Bob Loveless was right: 154cm makes a nice knife blade.

-
Most blades I carry/use are 420HC and 440C stainless (I won't be upset if I leave cheap knife laying around and it goes missing). I sweat a lot(kind of sweat that drips from pants and shirt, then leaves white marks of salt) and non-stainless blades get spotty and pitted in a day or two on my belt or in my pocket. I would have to oil a non-stainless blade several times a day. Can't be bothered. :ahhh
Stainless blades will spot up on my as well, but it takes a week or two, then being stainless, it is easy to clean off the surface spots. :)
I like carbon steel patina, but I just can't carry them. I have several carbon steel knives, but they sit clean and spot free in the collections. :)
-
I've always found it interesting that even the most snobby of knife steel aficionados carry SAKs. I have no issue keeping my "higher end" steels sharp as others tend to bring up when talking about steels. That out the way, I like the "higher end" steels and many carbon steels as well. I've got a good variety I think but I'd like to try a few others like 3V, 10V, Elmax, and some of the interesting steels Spyderco uses.
Lets start with Vic steel. I have no issues. Razor sharp and performs each and every time. Even the most snobby of knife snobs carry a SAK from what I can see and read.
Steels on my MT, fixed blades, and folders. My S30V MT blade and Spyderco Native, 154CM MT and folder, ZDP189 Sypderco which I like very much, 01, A2, 1095, and
, oh and M390. I like them all. Does LMs 420HC work? Of course it does. I don't carry a stone or ceramic rods with my for work. I also dont carry them for my off days. I've had days where I've dulled my Vic blade and LM Wave blade. Did they still cut? Yes but when I can get more performance out of a higher end steel then why not? -
I would say I'm rather obsessed with steel, but what I play with and what I carry are 2 different matters.
What I've established is 8Cr13 is not good enough for me, but H1 is.
I have no doubt all the other fascinating steels are more than adequate, I just don't have the budget. My only concern with some is sharpening, but I have no experience.
I 100% prefer carbon/tool steels, but for something I can carry in my pocket, rinse under the tap and throw back in my pocket without worrying about rust in unseen places is pretty good.
Voted for first option for the sake of H1, #2 is also good for me.
-
I'm sure most of you have seen this.......I need some M390 in my life :facepalm:
-
@gerleatherberman said:
I sweat a lot(kind of sweat that drips from pants and shirt, then leaves white marks of salt) and non-stainless blades get spotty and pitted in a day or two on my belt or in my pocket. I would have to oil a non-stainless blade several times a day. Can't be bothered. :ahhhStainless blades will spot up on my as well, but it takes a week or two, then being stainless, it is easy to clean off the surface spots. :)
being in a similar situation as you, GLBM; I wholeheartedly recommend you trying out an H1 blade,

any of them, preferably in Serrated Edge 8)It was an eye opener for me

-
While I dont have H1 everything I've read about this steel and others experiences I agree with TP. Might be a good test of this steel GLBM. If I had one I'd send it your way for you to test.
-
I keep all my knives sharp, from low end 420 to super steels, and they all perform when I need to cut something. I am not a power user that cuts stuff 100 times a day anyway. My preference goes to stainless, though I have a few that take a patina, like this K390.

-
I like my 154cm. Great balance of all the advantages of different metals.
-
I like most steels
I really dont have any of the super steels but I do love H1
it is just about maintenance free except for the sharpening part :D I have a PE blade and keep it sharp by just stropping with leather and a polishing compound
Other than that I will use just about any steel, even carbon with a patina ::) :D -
@CallsignBadger said:
I like my 154cm. Great balance of all the advantages of different metals.154CM is a very nice upgrade, thats still easy to sharpen.
-
I carried a Wave standard version 2 for years, sure the 420 blade gets dull quick but all I'm doing is busting tape , cutting into AV equipment packages so no biggie.
I find a Charge Ti with 154 and I'm loving it . Use it hard for bout 4 years now. I have little chips all up and down the blade and i was being a dumbass and broke the very tip off. Used it as a flathead in a pinch for a bit
That 154 would bite me quite a bit being super sharp. :o :oNow I'm back to a Wave Plus with 420HC which will keep me going until my Ti is back from getting some work.
-
I've tried lots of steels, but 154cm seems to be a good all-around balance for me.

-
@CallsignBadger said:
I like my 154cm. Great balance of all the advantages of different metals.I like my 154cm. Great balance of all the advantages of different metals.
154CM is a very nice upgrade, thats still easy to sharpen.
@Nix said:
I've tried lots of steels, but 154cm seems to be a good all-around balance for me.
lots of people like to criticise Emerson for still using that same steel in their knives since 15 years ago, but he gave a personal response to that last week, ::)
I thought it was interesting especially to those in favor of 152CM/CPM154
https://www.bladeforums.com/threads/emerson-explains-154-steel.1599731/page-1
and also, I know some of you (myself included) are very fond of the Buck 110,
do you know that Buck released an exclusive 110LW (lightweight) model this year with 154CM? It's called the Smokejumper
https://www.skblades.com/product-page/the-smoke-jumper
Here's a thread about it, with pics
love that red color -
I hadn't seen that Buck 110. Very cool.

-
I like my 154cm. Great balance of all the advantages of different metals.
I like my 154cm. Great balance of all the advantages of different metals.
154CM is a very nice upgrade, thats still easy to sharpen.
@Nix said:
I've tried lots of steels, but 154cm seems to be a good all-around balance for me.
lots of people like to criticise Emerson for still using that same steel in their knives since 15 years ago, but he gave a personal response to that last week, ::)
I thought it was interesting especially to those in favor of 152CM/CPM154
https://www.bladeforums.com/threads/emerson-explains-154-steel.1599731/page-1
and also, I know some of you (myself included) are very fond of the Buck 110,
do you know that Buck released an exclusive 110LW (lightweight) model this year with 154CM? It's called the Smokejumper
https://www.skblades.com/product-page/the-smoke-jumper
Here's a thread about it, with pics
love that red color
Thanks for letting me know about this model. The price is excellent, provided it's about the same a leather sheath 420HC model is now. Upgraded steel, bright handles, and something a bit easier to tote around than some half-pound beast. Glad I waited when I wanted to buy one at my local knife store shortly after they came out (but I still ended up buying a Nano Bantam), and this is only $10 more than what they wanted for the standard model 110LT. And I really like that red and black nylon sheath. Nylon is truly better for a working knife's sheath because it can be easily cleaned.Now if only they'll start offering the LT frame in a myriad of colors in the custom shop--this same knife, but with a black coated blade would be awesome. And I'd really like an orange or blue one.
-
For me, it's both high carbon and stainless. Really, I don't care as long as it holds an edge well and is easy to resharpen. So far, Sandvik 12C27, as used by Mora and EKA has performed best in terms of edge retention and corrosion resistance, as well as ease of resharpening. I cut up half a soft plastic (but still thick) kiddie pool with an EKA Swede 88, and it was still decently sharp. The Queen Big Chief I used (which is like an inch longer), which is 440A, had to be resharpened 3 times during the job on the other half.
-
I sweat a lot(kind of sweat that drips from pants and shirt, then leaves white marks of salt) and non-stainless blades get spotty and pitted in a day or two on my belt or in my pocket. I would have to oil a non-stainless blade several times a day. Can't be bothered. :ahhh
Stainless blades will spot up on my as well, but it takes a week or two, then being stainless, it is easy to clean off the surface spots. :)
being in a similar situation as you, GLBM; I wholeheartedly recommend you trying out an H1 blade,

any of them, preferably in Serrated Edge 8)It was an eye opener for me

Thank you for the information, TP!

I've been curious as of late about H1. I rarely use serrated, so I would go plain edge, but I do like the look of them. :D@Aloha007 said:
While I dont have H1 everything I've read about this steel and others experiences I agree with TP. Might be a good test of this steel GLBM. If I had one I'd send it your way for you to test.Thank you for the confirmation, Aloha!

I will put an H1 knife on my "to get list" and find one to buy/carry soon. Would be nice not worrying about the knife edge getting dull from just being in my pocket if I forget to oil it up.

-
I own a few non-stainless Damascus blades, otherwise it´s stainless all the way. Ease of maintenance being the most important reason.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login