Wave Scissors
-
After a couple of weeks from getting my wave i was cutting some coconut palms with the scissors everything was going fine until stop cutting, i thougth it was just to thick then i want to close de scissors but i couldnt the scissors doesnt close because some dents apear in the blade, i went to the welding workshop at work and with a big metal file down until close, after that the scissor doesnt cut very well.
How can i sharpen or correct the scissors? any advice?
Sorry if my writing its bad corrections are welcome



-
Scissors aren't the easiest to sharpen. Using a small file, follow the bevel as closely as you can on both cutting surfaces of the scissors. You'll also have to lightly de-burr the opposite sides of where you filed, the flat sides of the scissors. Go slow and check the cutting ability on paper till you are happy. I hope that made sense.
-
Scissors can be tricky to sharpen and I'm no expert.
The inner face of the blades has to be flat. In general, there should not be any play or wiggle between the blades. My WAVE does have a slight amount of play, but it still cuts well. But too much play can lead to the material being cut just folding up in the jaws of the scissors.
When resharpening, I try to just sharpen the angled part of the edge. If the inner face needs to be cleaned up because of a rolled edge or burr, I try to remove that with a flat stone, very carefully.
If your WAVE's scissors are loose, with a lot of play between the blades, they may not cut well. You could try to peen the rivet that used to form the pivot. Be sure to support the entire length of the lower blade so it doesn't get bent during peening. You might use a metal punch to keep the peening very precise and avoid hitting the upper blade.
Or you contact Leatherman and see about getting your WAVE repaired!
-
@Aloha007 said:
Scissors aren't the easiest to sharpen. Using a small file, follow the bevel as closely as you can on both cutting surfaces of the scissors. You'll also have to lightly de-burr the opposite sides of where you filed, the flat sides of the scissors. Go slow and check the cutting ability on paper till you are happy. I hope that made sense.Thick materials cut very well but when some thin or like ruber doesnt, or some fabric have to cut many times but finally it will do it.
-
@Nix said:
Scissors can be tricky to sharpen and I'm no expert.The inner face of the blades has to be flat. In general, there should not be any play or wiggle between the blades. My WAVE does have a slight amount of play, but it still cuts well. But too much play can lead to the material being cut just folding up in the jaws of the scissors.
When resharpening, I try to just sharpen the angled part of the edge. If the inner face needs to be cleaned up because of a rolled edge or burr, I try to remove that with a flat stone, very carefully.
If your WAVE's scissors are loose, with a lot of play between the blades, they may not cut well. You could try to peen the rivet that used to form the pivot. Be sure to support the entire length of the lower blade so it doesn't get bent during peening. You might use a metal punch to keep the peening very precise and avoid hitting the upper blade.
Or you contact Leatherman and see about getting your WAVE repaired!
I dont remember if wiggle betwen the baldes exist before this issue but now it does just a little, ill try to sharpen with a fine stone or very small file.
I also saw on the internet cutting aluminum foil will do it or with paper clip not cutting but try to.
-
Dont file that other side, only if it absolute necessary. Filing scissor isnt easy and most of people will fail it so that scissors are useless after sharpening

Only Tools Matters
-
Yes, like Antti says.. Never file that face, it will just create a gap between the scissors and they'll never work again properly!
Just file the edges lightly until they cut like Nix and Aloha have said then lightly remove any burrs with a stone or such-like... -
@Antti Lammi said:
Dont file that other side, only if it absolute necessary. Filing scissor isnt easy and most of people will fail it so that scissors are useless after sharpening
Only Tools Matters

-
@Antti Lammi said:
Dont file that other side, only if it absolute necessary. Filing scissor isnt easy and most of people will fail it so that scissors are useless after sharpening

Only Tools Matters
I had to file the inner side cause a Rolled edge doesnt let the scissors close.
File it only lightly, if you file it too much there will be gap and you can say bye bye for scissors. If that happens you could send it warranty (not sure will that kinda go through warranty) or change yourself scissors.
Only tools matters
-

Its a tricky process, so take your time.
Good luck, sir

-
Some good advice is already been given
so all I will say is good luck in getting them back in order 
-
I have at work some files that my chainsaw operator uses to sharpen the chain do you thing some of this will help me? maybe the flat file? or i need a smaller file



-
I would only use the flat file
it would be best to use a sharpening stone or small flat diamond card 
Guess I still had to put my input in ::) :D
-
Thanks everyone with the help i hope i can fix this i love my wave just make me sad about the scissors i know i know my fault.

I also hear the scissors can cut a medium size zip tie is that right?
-
It is possible, but I'm cautious with zip ties. Some can be hard and dent the edges of scissors. If you do cut a zip tie, be sure the blades are starting the cut at the corners of the zip tie.

-
It is possible, but I'm cautious with zip ties. Some can be hard and dent the edges of scissors. If you do cut a zip tie, be sure the blades are starting the cut at the corners of the zip tie.

better with the knife so no risk will taken
If you can access the zip tie with the wire cutter they work well too. I sniped a bunch with my LM Squirt P4 wire cutters.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login