The Great Multi-Tool Restoration Thread!!!
-
It's back on again I found one :D
-
[quote author=DaveK link=topic=9321.msg174471#msg174471 date=1235341425]
Budgies are cheaper than shoes Ben - I suggest that you embrace it ;)Shoes don't make bloody noise all the time and shoot bird seed around your front room though do they!?! >:( :D
Or Stink , oh hang on the misses work shoes have a smell that would offend a skunk. One Christmas I gave her a pair of odour eaters for her work shoes as a joke . Apparently not very funny ::) ::) :D :D
I am guessing it went a bit like this
then to get away like this :ahhh
I can only imagine because this would have been the outcome if I had done that :DThe misses thought it was funny , but her friends on the other hand ::) ::) :D
[/quote]See that's why you need to keep them from having friends ::) :D
My wife usually only goes places with her sister and she a pretty good egg so I don't have to worry much

-
Here's the latest. This was in a bit of a mess when it arrived this morning, but I've stripped it right down, cleaned it and taken some fine sandpaper to it since.
I'm actually very pleased with this one, the file is slightly bent (but still useable), and the screws were so badly seized that I damaged one of them a little taking it apart, otherwise you would struggle to tell it from new. This one's going into my EDC as from tomorrow.

-
@DaveK said:
Here's the latest. This was in a bit of a mess when it arrived this morning, but I've stripped it right down, cleaned it and taken some fine sandpaper to it since.I'm actually very pleased with this one, the file is slightly bent (but still useable), and the screws were so badly seized that I damaged one of them a little taking it apart, otherwise you would struggle to tell it from new. This one's going into my EDC as from tomorrow.

Dave, very nice mate!
Do you ever use steel wool on your multi's? I find it works great fro removing surface rust and it doesn't scratch the tool. 
-
I do, yes. In fact I did on this one for parts.
My basic "process" goes like this:
- Take it completely apart;
- Seperate all the parts and place them in a tub - drown in WD40 to loosen any rust / crud / old loctite;
- Let it soak there for at least an hour;
- Remove from the WD40 wipe / scrape off any rust crud etc, rinse;
- Spray with a disinfectant cleaning fluid - leave for 30 minutes;
- Wash with washing up liquid using wire wool and tooth brush;
- Dry all parts and get busy with the sandpaper to remove deeper rust / scratches / nicks;
- Put it back together and apply loctite;
- Oil.
-
@DaveK said:
I do, yes. In fact I did on this one for parts.My basic "process" goes like this:
- Take it completely apart;
- Seperate all the parts and place them in a tub - drown in WD40 to loosen any rust / crud / old loctite;
- Let it soak there for at least an hour;
- Remove from the WD40 wipe / scrape off any rust crud etc, rinse;
- Spray with a disinfectant cleaning fluid - leave for 30 minutes;
- Wash with washing up liquid using wire wool and tooth brush;
- Dry all parts and get busy with the sandpaper to remove deeper rust / scratches / nicks;
- Put it back together and apply loctite;
- Oil.
Great, thanks for the run down...
What oil do you use for the PST's? -
Dave, what grit sandpaper? Thanks
-
I'm using 3 in 1 PTFE oil at the moment, it seems to work well and doesn't get all cruddy like the regular stuff.
LM123 - it's in the picture ;) (1500 grit)
-
Maybe I should go to bed! :D
-
Very nice PST Dave :o looks brand new
I like a nice and shiny PST
Thanks for the rundown of what you do to 1 I may start tracking these beauties down and cleaning them up myself
I will use that as a reference 
-
Let's keep this thread alive.

-
OK - Let's!
Neil (NKB) sent me a Kershaw A100 in a trade, and it arrived today. Neil had warned me that it was a bit grubby, so it was a planned clean-up job!
Here it is before:


During:

...and after!


-
That is looking SO much better. Top job

Neil
-
Nice work. Especially on that saw blade!

-
Great job, Dave!

-
Great job Dave another top notch clean up

You are getting very good at that
:D
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

:D :D