September Storm: 30 days of Waves
-
I was comparing the Charge AL and the Wave+ today. I'm a bit surprised to find that the Charge is bigger in every dimension than the Wave. Not sure why this should come as news to me at this point in my life; I guess I never held two side by side before.

You guys awlready know that the tools sets are the same. Different blade steels, different handle materials, and the Wave+ has replaceable wire cutters. The pliers head are slightly differentto allow the Wave to accommodate the replaceable cutters.
With a pocket clip attached to both tools, the Charge weighs in at 248 grams on my scale, the Wave a wee bit less at 244 grams. I thought the aluminum handle scales would lighten the Charge a bit more than that. Apparently not the case.
I had a bit more fencing to put up and test the wire cutters on tie-wire and the actual fencing. The fencing is thicker and harder than the wire.
Both tools cut these materials easily. Neither tool's cutter suffered any damage.
I will say that my subjective impression was that the Wave cut the materials more easily. The cutters seem sharper. And when cutting the Wave is quieter, especially with the softer wire.

Neither set of cutters did very well cutting the piece of rebar, but you can't have everything with a pocket tool. I'll call that a tie.
However, overall, I find I favor the Wave over the Charge at the moment. The big handles on the Charge are more comfortable, for me, but I value the slimmer profile of the Wave. And, hey, it's 4 grams lighter, so even guys like NutSAK can carry it.
that was a cool comparison and write up
-
I was comparing the Charge AL and the Wave+ today. I'm a bit surprised to find that the Charge is bigger in every dimension than the Wave. Not sure why this should come as news to me at this point in my life; I guess I never held two side by side before.

You guys awlready know that the tools sets are the same. Different blade steels, different handle materials, and the Wave+ has replaceable wire cutters. The pliers head are slightly differentto allow the Wave to accommodate the replaceable cutters.
With a pocket clip attached to both tools, the Charge weighs in at 248 grams on my scale, the Wave a wee bit less at 244 grams. I thought the aluminum handle scales would lighten the Charge a bit more than that. Apparently not the case.
I had a bit more fencing to put up and test the wire cutters on tie-wire and the actual fencing. The fencing is thicker and harder than the wire.
Both tools cut these materials easily. Neither tool's cutter suffered any damage.
I will say that my subjective impression was that the Wave cut the materials more easily. The cutters seem sharper. And when cutting the Wave is quieter, especially with the softer wire.

Neither set of cutters did very well cutting the piece of rebar, but you can't have everything with a pocket tool. I'll call that a tie.
However, overall, I find I favor the Wave over the Charge at the moment. The big handles on the Charge are more comfortable, for me, but I value the slimmer profile of the Wave. And, hey, it's 4 grams lighter, so even guys like NutSAK can carry it.
Wow, thanks a million Nix for testing this.
Great comparison. I can sleep better now using Wave for the next 28 days to come
-
Mine are a bit stiff, too. I know some guys will oil them and work them a lot. But I've found that with time and use they break-in just fine.
Yeah, it's just strange why they are nice and free normally but go extremely tight when I've used quite a bit of force then won't loosen up until I give them a "tap"on something solid!
It's probably newness, like I said my Rebar pliers were exactly the same and are ok now, maybe a bit loose!! -
Day 2
Today's post is about the differences between the ReWaveR and a stock Wave. I might go into some more detail in subsequent daily posts as warranted by special uses.
First and most visible is the Rebar pliers head. Others have done this before me, the reason usually being the exchangeable cutters. Of course the Wave + has made that obsolete, but only to an extent as the Rebar pliers are manifestly more solid.
Then the PE blade, this was swapped out for a 154CM one normally found in a Charge. The same was done to the SE blade - I thought the hook blade looked cool but have yet to ascertain the utility.
Notably no longer present are the bit drivers, both large and small, and the scissors. Instead, the ReWaveR sports a fixed Phillips, an awl and a small fixed screwdriver, all out of a Rebar, duly filed down where necessary (the awl from another small Rebar screwdriver, then sharpened and drilled) to account for the more limited space available in the Wave handles and to allow the Rebar plier head to fit in.
Still present the large flat blade and the can opener.

-
+1

-
The best of both tools


-
@Dutch_Tooler said:
Day 2Today's post is about the differences between the ReWaveR and a stock Wave. I might go into some more detail in subsequent daily posts as warranted by special uses.
First and most visible is the Rebar pliers head. Others have done this before me, the reason usually being the exchangeable cutters. Of course the Wave + has made that obsolete, but only to an extent as the Rebar pliers are manifestly more solid.
Then the PE blade, this was swapped out for a 154CM one normally found in a Charge. The same was done to the SE blade - I thought the hook blade looked cool but have yet to ascertain the utility.
Notably no longer present are the bit drivers, both large and small, and the scissors. Instead, the ReWaveR sports a fixed Phillips, an awl and a small fixed screwdriver, all out of a Rebar, duly filed down where necessary (the awl from another small Rebar screwdriver, then sharpened and drilled) to account for the more limited space available in the Wave handles and to allow the Rebar plier head to fit in.
Still present the large flat blade and the can opener.

-
Day 02
So today its time toi change the coils of my vape so i will use the bit kit to do this.
IMG_2244 by alvaroolmos, en FlickrAnd the hex driver its the indicated for the job.
IMG_2245 by alvaroolmos, en Flickri lose some weight a time a go, so my belt needed a new hole again the wave comes into the scene.
IMG_2212 by alvaroolmos, en FlickrAt this point i missed the lack of an awl in the wave but the main blade did the job very well
IMG_2213 by alvaroolmos, en Flickr -
Nice!

Good improvisation with the main blade.

-
Excellent jobs aolmos

-
Thanks Steve, Wspeed, CallsignBadger and Obi

Good improvisation with the main blade.

+1!
I'm probably overly fussy as I try not to use the main blade for that kind of jobs because it has quite a bit of taper and will leave holes in the leather which are unnecessarily large at the surface. One of the reasons why I built an awl for the ReWaveR. -
@Dutch_Tooler said:
Thanks Steve, Wspeed, CallsignBadger and Obi
Nice!

Good improvisation with the main blade.

+1!
I'm probably overly fussy as I try not to use the main blade for that kind of jobs because it has quite a bit of taper and will leave holes in the leather which are unnecessarily large at the surface. One of the reasons why I built an awl for the ReWaveR.Yeah I thought that too that’s why went to the middle then turn around did the same thing so the hole doesn’t get to big
-
I'm out fellas as my heart just isn't in it :-\ I'll enjoy following along with you all though as I'm sure it will be an epic challenge

-
Farewell, Steve

Enjoy trying to keep up with the posts :D
-
Great uses all
sorry to hear you're out Steve. :-\ but I do understand 
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
