September Storm: 30 days of Waves
-
Day 2
Today's post is about the differences between the ReWaveR and a stock Wave. I might go into some more detail in subsequent daily posts as warranted by special uses.
First and most visible is the Rebar pliers head. Others have done this before me, the reason usually being the exchangeable cutters. Of course the Wave + has made that obsolete, but only to an extent as the Rebar pliers are manifestly more solid.
Then the PE blade, this was swapped out for a 154CM one normally found in a Charge. The same was done to the SE blade - I thought the hook blade looked cool but have yet to ascertain the utility.
Notably no longer present are the bit drivers, both large and small, and the scissors. Instead, the ReWaveR sports a fixed Phillips, an awl and a small fixed screwdriver, all out of a Rebar, duly filed down where necessary (the awl from another small Rebar screwdriver, then sharpened and drilled) to account for the more limited space available in the Wave handles and to allow the Rebar plier head to fit in.
Still present the large flat blade and the can opener.

-
+1

-
The best of both tools


-
@Dutch_Tooler said:
Day 2Today's post is about the differences between the ReWaveR and a stock Wave. I might go into some more detail in subsequent daily posts as warranted by special uses.
First and most visible is the Rebar pliers head. Others have done this before me, the reason usually being the exchangeable cutters. Of course the Wave + has made that obsolete, but only to an extent as the Rebar pliers are manifestly more solid.
Then the PE blade, this was swapped out for a 154CM one normally found in a Charge. The same was done to the SE blade - I thought the hook blade looked cool but have yet to ascertain the utility.
Notably no longer present are the bit drivers, both large and small, and the scissors. Instead, the ReWaveR sports a fixed Phillips, an awl and a small fixed screwdriver, all out of a Rebar, duly filed down where necessary (the awl from another small Rebar screwdriver, then sharpened and drilled) to account for the more limited space available in the Wave handles and to allow the Rebar plier head to fit in.
Still present the large flat blade and the can opener.

-
Day 02
So today its time toi change the coils of my vape so i will use the bit kit to do this.
IMG_2244 by alvaroolmos, en FlickrAnd the hex driver its the indicated for the job.
IMG_2245 by alvaroolmos, en Flickri lose some weight a time a go, so my belt needed a new hole again the wave comes into the scene.
IMG_2212 by alvaroolmos, en FlickrAt this point i missed the lack of an awl in the wave but the main blade did the job very well
IMG_2213 by alvaroolmos, en Flickr -
Nice!

Good improvisation with the main blade.

-
Excellent jobs aolmos

-
Thanks Steve, Wspeed, CallsignBadger and Obi

Good improvisation with the main blade.

+1!
I'm probably overly fussy as I try not to use the main blade for that kind of jobs because it has quite a bit of taper and will leave holes in the leather which are unnecessarily large at the surface. One of the reasons why I built an awl for the ReWaveR. -
@Dutch_Tooler said:
Thanks Steve, Wspeed, CallsignBadger and Obi
Nice!

Good improvisation with the main blade.

+1!
I'm probably overly fussy as I try not to use the main blade for that kind of jobs because it has quite a bit of taper and will leave holes in the leather which are unnecessarily large at the surface. One of the reasons why I built an awl for the ReWaveR.Yeah I thought that too that’s why went to the middle then turn around did the same thing so the hole doesn’t get to big
-
I'm out fellas as my heart just isn't in it :-\ I'll enjoy following along with you all though as I'm sure it will be an epic challenge

-
Farewell, Steve

Enjoy trying to keep up with the posts :D
-
Great uses all
sorry to hear you're out Steve. :-\ but I do understand 
-
** Day 2 of 30**
Not much for me to use a MT on Sunday for but I was thinking about cutting the side a couple roses from one of our rose bushes but this one isn't hardly ready
:D I have used this type scissor before and they do work for this quite well 
2018-09-02_06-28-10 by Poncho 65, on Flickr -
Sorry to see you go, Steve!

-

Love that orange!

-
Love that orange!

This one was given to me courtesy of our challenge host Nix, several months back

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
