September Storm: 30 days of Waves
-
DAY 11 Busy all day forgot post this




-
Whatever makes the blade sharp for you is what you need. :)
Day 11:
Had a Doctor's appointment, and didn't do anything useful today. But, here is the Wave in my carry today. :)Let’s see what came out it’s mi first sharpening I’m afraid to mes it up.
Nice edc today
Thank you, aolmos!

I didn't realize you were new to sharpening. I think the swipe sharpeners are o.k. for many people. I don't think it could do any irreversible damage. The Wave blade is pretty forgiving. But, definitely look around MT.o for sharpening tips. Lots of great knife sharpening threada around here. :)
-
Day 12
One other mod in the ReWaveR is the replacement of the large bit driver with a fixed Phillips from a Rebar. This adds a bit of reach, at the cost however of allowing exchangeable bits to be used only in combination with the Removable Bit Driver (with the added advantage however of allowing use of standard 1/4" bits in that case). This mod requires the removal of some material, e.g. with the file mentioned in my previous post, from the handle and nail nick area of the Phillips as the first two pics below show (in comparison with a BO Phillips in the Rebar shown).
The plier rest tabs in that handle will also need to be removed - carefully - you don't want to change the lock spring action. The last pic shows an additional indent one will need to make in the lock spring, to allow the Phillips head to come down deeply enough inside the handle (without prejudicing the Phillips by e.g. filing off a bit from the head). The small indent can be fashioned with a Dremel and cutting disc or another bit; take care not to prejudice the rivet's hold or the spring action. Just goes to show it's a tight fit - the Wave handles do not give you a lot of space to play with.
Which brings me back to something I'd forgotten to mention in my previous post - the plier rest tab in the opposite handle will also have to be removed in order to allow the small fixed driver and awl to rest deeply enough inside the handle as well. The fit, already tight with a normal Wave(+) pliers head, becomes a little bit tighter still when you elect to use a Rebar pliers head.
The Rebar pliers head, more or less about as wide as a Wave head, does have a slightly larger contour in places - more specifically the rectangular side brace areas in the stretch between and around the pivot and the cutouts for the removable cutters. These brace areas - in combination with the removable cutters - were what originally attracted me to the Rebar pliers head in the first place, even before any sign appeared of the new Plus plier heads. The new Plus plier heads for Wave and Charge instinctively look to me as if they might be a tad weak around the cutter cutouts - I'd be more than happy to be proven wrong though. Anyone have any negative experience with the Plus heads yet?




-
Nice job, D_T!

Oh, the topic of the plus plier head has been extensively mulled over. Myself also sceptical to begin with. However, looking into the common breakage locations of the Wave pliers, it is notable that the removed material (for cutters) doesn't seem to be an area of typical weakness. I'm not saying it is NOT a potentially problematic issue, but I think the design should be sufficient for a cast plier head with replaceable cutters. MTs should never be used as hard as dedicated hand tools. That is the main reason MTs suffer damage. Too many people think MT pliers will be as good as a cheap set of drop forged tool-steel pliers, and this is not the case. Some MT pliers are amazingly strong, but they're not going to be as strong as a decent set of drop forged pliers. :)
So, in short, the plus plier head should be of similar strength to the previous Wave plier head, because the common breakage occurs in an area not affected by the material removed for the cutters. I will be happy to change my position if breakage begins to occur in the areas affected by the addition of replaceable cutters.
-
@gerleatherberman said:
Nice job, D_T!
Oh, the topic of the plus plier head has been extensively mulled over. Myself also sceptical to begin with. However, looking into the common breakage locations of the Wave pliers, it is notable that the removed material (for cutters) doesn't seem to be an area of typical weakness. I'm not saying it is NOT a potentially problematic issue, but I think the design should be sufficient for a cast plier head with replaceable cutters. MTs should never be used as hard as dedicated hand tools. That is the main reason MTs suffer damage. Too many people think MT pliers will be as good as a cheap set of drop forged tool-steel pliers, and this is not the case. Some MT pliers are amazingly strong, but they're not going to be as strong as a decent set of drop forged pliers. :)
So, in short, the plus plier head should be of similar strength to the previous Wave plier head, because the common breakage occurs in an area not affected by the material removed for the cutters. I will be happy to change my position if breakage begins to occur in the areas affected by the addition of replaceable cutters.
I totally agree with u. The breakage was never at the cutter area. Its usually near to the pivot. At least I have never seen one. Though I never had to use one hard enough to break one. Unless I was feeling stupid that day and doing stupid things.
-
Hello Team
Well so am back from airplanes and a dreadfully long meeting so what better way to say hello to my favourite LM ....
One of their most important uses .

-
Day 12



-
Day 12
My glasses were irritating me where they go over the ears! When I looked I noticed the plastic bits at the ends had broken off leaving sharp edges!
I rounded them off with the rough file then smoothed them with the diamond part.
They feel more comfortable now




-
Oops had a very very busy day yesterday, long meetings and worked late on replacing HD’s on a few old laptops with SSD drives. Dit take a pic but forgot to post before i went to bed.
Day 11:
using small driver from the bit kit on the wave to remove those HD’s screws from the cage, and put them back on the ssd.
-
Excellent pics and uses again everyone

-
Day 12
I noticed that the knobs on the drawers
on my storage box are loose when I first got itSo today I had enough of the knobs
I used the Wave flat bit driver to tighten the screwsNo real problem but because of the
small drawers low height I could
only just use the driver with small turns
Larger drawers no problems at all



-
Glad you sorted your knobs out Speedy!! ;)
-
Day 11 - (no access on Tuesday!, again) At work replacing ceiling tiles, and first one set to replace had a dust sensor mounted dead center.
Used the WAVES PE to score the junction box location and outline, then the Saw blade to cut the hole. Did the job with out an issue.
-
I noticed that the knobs on the drawers
on my storage box are loose when I first got itSo today I had enough of the knobs
I used the Wave flat bit driver to tighten the screwsNo real problem but because of the
small drawers low height I could
only just use the driver with small turns
Larger drawers no problems at all

-
@Jaypeebee said:
Glad you sorted your knobs out Speedy!! ;)Thanks Jaypeebee they were getting on my nerves

-
Day 12/30
This day wasnt so good to me [emoji26] i losted my HalfWave today, prolly dropped to swapm where we were cause i didnt found it elswhere. I used it today openin some packages and i used my Wave today to repair my ecig, needed to replace new wick and also changed broken glass to my tank.
Only Tools Matters

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login