September Storm: 30 days of Waves
-
Nice job, D_T!

Oh, the topic of the plus plier head has been extensively mulled over. Myself also sceptical to begin with. However, looking into the common breakage locations of the Wave pliers, it is notable that the removed material (for cutters) doesn't seem to be an area of typical weakness. I'm not saying it is NOT a potentially problematic issue, but I think the design should be sufficient for a cast plier head with replaceable cutters. MTs should never be used as hard as dedicated hand tools. That is the main reason MTs suffer damage. Too many people think MT pliers will be as good as a cheap set of drop forged tool-steel pliers, and this is not the case. Some MT pliers are amazingly strong, but they're not going to be as strong as a decent set of drop forged pliers. :)
So, in short, the plus plier head should be of similar strength to the previous Wave plier head, because the common breakage occurs in an area not affected by the material removed for the cutters. I will be happy to change my position if breakage begins to occur in the areas affected by the addition of replaceable cutters.
-
@gerleatherberman said:
Nice job, D_T!
Oh, the topic of the plus plier head has been extensively mulled over. Myself also sceptical to begin with. However, looking into the common breakage locations of the Wave pliers, it is notable that the removed material (for cutters) doesn't seem to be an area of typical weakness. I'm not saying it is NOT a potentially problematic issue, but I think the design should be sufficient for a cast plier head with replaceable cutters. MTs should never be used as hard as dedicated hand tools. That is the main reason MTs suffer damage. Too many people think MT pliers will be as good as a cheap set of drop forged tool-steel pliers, and this is not the case. Some MT pliers are amazingly strong, but they're not going to be as strong as a decent set of drop forged pliers. :)
So, in short, the plus plier head should be of similar strength to the previous Wave plier head, because the common breakage occurs in an area not affected by the material removed for the cutters. I will be happy to change my position if breakage begins to occur in the areas affected by the addition of replaceable cutters.
I totally agree with u. The breakage was never at the cutter area. Its usually near to the pivot. At least I have never seen one. Though I never had to use one hard enough to break one. Unless I was feeling stupid that day and doing stupid things.
-
Hello Team
Well so am back from airplanes and a dreadfully long meeting so what better way to say hello to my favourite LM ....
One of their most important uses .

-
Day 12



-
Day 12
My glasses were irritating me where they go over the ears! When I looked I noticed the plastic bits at the ends had broken off leaving sharp edges!
I rounded them off with the rough file then smoothed them with the diamond part.
They feel more comfortable now




-
Oops had a very very busy day yesterday, long meetings and worked late on replacing HD’s on a few old laptops with SSD drives. Dit take a pic but forgot to post before i went to bed.
Day 11:
using small driver from the bit kit on the wave to remove those HD’s screws from the cage, and put them back on the ssd.
-
Excellent pics and uses again everyone

-
Day 12
I noticed that the knobs on the drawers
on my storage box are loose when I first got itSo today I had enough of the knobs
I used the Wave flat bit driver to tighten the screwsNo real problem but because of the
small drawers low height I could
only just use the driver with small turns
Larger drawers no problems at all



-
Glad you sorted your knobs out Speedy!! ;)
-
Day 11 - (no access on Tuesday!, again) At work replacing ceiling tiles, and first one set to replace had a dust sensor mounted dead center.
Used the WAVES PE to score the junction box location and outline, then the Saw blade to cut the hole. Did the job with out an issue.
-
I noticed that the knobs on the drawers
on my storage box are loose when I first got itSo today I had enough of the knobs
I used the Wave flat bit driver to tighten the screwsNo real problem but because of the
small drawers low height I could
only just use the driver with small turns
Larger drawers no problems at all

-
@Jaypeebee said:
Glad you sorted your knobs out Speedy!! ;)Thanks Jaypeebee they were getting on my nerves

-
Day 12/30
This day wasnt so good to me [emoji26] i losted my HalfWave today, prolly dropped to swapm where we were cause i didnt found it elswhere. I used it today openin some packages and i used my Wave today to repair my ecig, needed to replace new wick and also changed broken glass to my tank.
Only Tools Matters

-
Sorry about that! :'(
We live and lose. Such is the way of things. Maybe it is time for a new SAK! ;)
-
Sorry to hear you lost the Half Wave Antti...!!!

-
Sorry to hear that you lost the half Wave Antti

-
Thanks, well now i need some new tools, i think im gonna get these. Also if im lucky im going to get Blast what i can use to modify my other Leathermans
Only Tools Matters

-
Day 12
Not much to do for the Wave, so I figured I'll try our the least used tool on my old sunglasses that had lose screws. It worked fine but I think the "handle" is too big and heavy to get a sensible enough feedback of the tiny screw's status :D

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login