Seeking Rebar modding advice.
-
That’s perfectly normal
We all want the perfect MT

-
That’s perfectly normal
We all want the perfect MT

Okay good haha
Also makes it a lot personal and “special” to one self when it has been modded to ones personal needs
Sent from my iPhone using Tapatalk
You wouldn't want to know how many iterations (documented and otherwise) I have gone through... ::) :o :ahhh

-
That’s perfectly normal
We all want the perfect MT

Okay good haha
Also makes it a lot personal and “special” to one self when it has been modded to ones personal needs
Sent from my iPhone using Tapatalk
You wouldn't want to know how many iterations (documented and otherwise) I have gone through... ::) :o :ahhh

Actually I would like to know [emoji846]
I am constantly looking for ideas and inspiration, so by all means I would like to know [emoji6]
Sent from my iPhone using Tapatalk
-
Actually I would like to know [emoji846]
I am constantly looking for ideas and inspiration, so by all means I would like to know [emoji6]
Sent from my iPhone using Tapatalk
You asked for it... :D ;)
In very rough chronological order, I think (and leaving out quite a few undocumented position swaps):
/post/1577627
/post/1582735
/post/1593754
/post/1598008
/post/1598021
/post/1602330I believe that's all. Others have published many more good Rebar mod ideas in those two threads.
-
Just occurred to me that I forgot about mentioning one “mod” I also made in this thread (my “build” thread)
Sharpening of the replaceable cutters:


Results:
As you can see below; pretty dramatic results and difference.
Before:
Sometimes it wouldn't even cut all the way through.


After:
Cuts it clean and like a hot knife through butter

**Type of cable used: **
(Came off an old TV from the late 90s to early 2000s)
-
...
Actually I would like to know [emoji846]
I am constantly looking for ideas and inspiration, so by all means I would like to know [emoji6]
Sent from my iPhone using Tapatalk
You asked for it... :D ;)
In very rough chronological order, I think (and leaving out quite a few undocumented position swaps):
/post/1577627
/post/1582735
/post/1593754
/post/1598008
/post/1598021
/post/1602330I believe that's all. Others have published many more good Rebar mod ideas in those two threads.
Sorry, I didn't see your reply, but those are some amazing creations you have there!
I love the "colour swapped" ones...makes me almost want to look into getting black (BO) handles for mine...

-
Thanks MMR
Disclaimer: many of the creations are either copies of, or inspired by, mods where others have boldly gone before. -
@Dutch_Tooler said:
Thanks MMR
Disclaimer: many of the creations are either copies of, or inspired by, mods where others have boldly gone before.I think it will be difficult for someone to claim copyright on homemade mods [emoji6] ....plus, this is not a competition anyway, we are all here because we share the same passion and interest in these tools, and want to connect with people of similar interest too.....so no hard feelings if someone takes inspiration / copies ideas from another member.
If anything; I'd feel honoured if something that I did/made/build would serve as an inspiration to others
-
Not a mod; but found this 2D bit kit at a local hunting & fishing store on sale, so I grabbed it.

I will likely try to come up with a “mod” way of storing it though
Sent from my iPhone using Tapatalk
-
Nice one MMR

Like to see what you come
up with for storing the flat bits

-
Okay, I am just testing an idea out here, so bare with me.
Zip tie moment 1:
With the bit kit, I want to keep the two bit holders together, mainly so when I reach for the bit kit it will be pulled out as one unit and not risk pulling out one and then dropping the other.
But also because the holders have a smooth side on the back, so they will go in and out of the sheath smoother and lower the risk of a bit getting caught.
I did this using small zip ties and shrink tube, to prevent the locks on the zip ties from moving in and tightening themselves more. I want to leave them a little loose so that it is easier to flip them over.



Zip tie moment 2:

So the bit kit fits perfectly into the single sheath my rebar came with.
So to test out an idea, I zip tied it to the side of the sheath for the Charge, like so:

Also this way I can still carry my 3D bits as well:

So it would sit on the belt like so:

Again; I am just testing out an idea here, to see if it works, if it makes the sheath too large, and of course if the idea is a good idea in practice (IRL)
Please share thoughts and other ideas with me, both on this and if you have any other (and better) ideas
Sent from my iPhone using Tapatalk
-
I can’t think of anything else on
how to store the bits in a better way
-
@Wspeed said:
I can’t think of anything else on
how to store the bits in a better way
“Nay leather” and “DeadSkins” makes custom sheaths, and they have a model that has a sheath for a bit kit too, but they are expensive....deadskin ones are like 170 day aus dollars.
And I will be frank and say I am not spending that kind of money on a sheath.
Leatherman makes a nylon sheath/ pouch thing for the bit kit too, but I am not a fan of Velcro and nylon sheaths.
My zip tie idea here was also based on costs and what I had laying around, if my Frankenstein sheath idea here turns out to be a good concept, then I might have a go at making one myself or take it to the next step somehow.
However; if it is the case that having one big sheath is a dumb idea, I will start experimenting with having 2 separate sheaths.
In the end; it’s all about finding out what works best for one self. [emoji846]
Sent from my iPhone using Tapatalk
-
One thing that has bothered me about my Rebar since I first got it, was that you can’t close both handles at the same time without them hitting each other without opening the pliers, and/or if one handle is in the closed position and the other in the open, then you have to open the pliers to close both handles.
And sometimes due to the handles hitting each other they would slam shut and pinch my hand or finger in the process.
So I had a go with the grinder to try to round them off, as pictured below.


Results are exactly what I hoped for, so now it’s a lot easier to open and close, and the handles can open and close independently from each other too, which makes it a lot easier to open and close one handedly too

Sent from my iPhone using Tapatalk
-
Nice job MMR

-
It almost makes wonder why LM designers the handles the way they did....they are so much better this way...
....that was one thing I always loved about my Kick, was how easy it is to open and close....and with that; how easy it is to use with one hand, if needed
Sent from my iPhone using Tapatalk
-
Good job MMR

Somehow that particular aspect of the Rebar handles has never bothered me, but you're right, why were they designed this way?

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login