September Storm: 30 days of Waves
-
I love that tool

-
I broke my screw today..
This was the "new" pliers that I was trying to break in a few day ago with the spring... I was rather desperate to get it looser as I found out it suffers from the "hard squeeze tight pivot syndrome".... I cut a whole bunch of cloth hanger today in my final bid to solve this issue. Very unfortunately.. I didn't realise that my screw had come loose.. The screw snapped.. Half the screw was broken in the pliers. Was able to get it out eventually.. Lucky me..
Check your screws people! And use some form of lock tight in them!
Btw, I had somewhat relieved myself from the challenge a few days ago when I stopped posting pictures. :P 30 days is a challenge too long for me! I missed my other stuffs...


-
Day 28
Opened some packages today, also used the bit driver at work but didn't get chance for photos!


-
@Sam Lim said:
I broke my screw today..This was the "new" pliers that I was trying to break in a few day ago with the spring... I was rather desperate to get it looser as I found out it suffers from the "hard squeeze tight pivot syndrome".... I cut a whole bunch of cloth hanger today in my final bid to solve this issue. Very unfortunately.. I didn't realise that my screw had come loose.. The screw snapped.. Half the screw was broken in the pliers. Was able to get it out eventually.. Lucky me..
Check your screws people! And use some form of lock tight in them!
Btw, I had somewhat relieved myself from the challenge a few days ago when I stopped posting pictures. :P 30 days is a challenge too long for me! I missed my other stuffs...

Thanks for the warning Sam

Sorry to hear that you couldn’t finish the challenge
-
@Sam Lim said:
I broke my screw today..This was the "new" pliers that I was trying to break in a few day ago with the spring... I was rather desperate to get it looser as I found out it suffers from the "hard squeeze tight pivot syndrome".... I cut a whole bunch of cloth hanger today in my final bid to solve this issue. Very unfortunately.. I didn't realise that my screw had come loose.. The screw snapped.. Half the screw was broken in the pliers. Was able to get it out eventually.. Lucky me..
Check your screws people! And use some form of lock tight in them!
Btw, I had somewhat relieved myself from the challenge a few days ago when I stopped posting pictures. :P 30 days is a challenge too long for me! I missed my other stuffs...

Hi Sam,
thanks for the warning

There should be some Loctite on it by factory though. And the replacement kit comes with prepared screws too. I wonder what happened on yours
Did you spot any evidence of some Loctite, or were the screws clean?
-
:o
My screws are fine, but the pivot is a bit tighter since all that wire cutting I did the other day.
It could be worse, considering your screw broke, so I am fine with my pivot. I am not fine with broken screws.If I ever have a screw break, I will ask for a replacement. The screws and wire cutters are not excluded from the warranty, so I expect a replacement.
Have you contacted LM about the screw? It would be interesting to see what they say. Will they replace it or just tell you to buy a new set?
-
Thankfully you got the broken part of the screw out Sam :ahhh I have had them loosen on both Rebars and ST300 cutters over the years
Never had one of the screws break though :oGreat pics all and sorry you didn't finish Sam

Also I am realizing I will be out of internet range for the last day of this month
So I will take the pic and when I get back I will post it
on to today's pic though 
-
Day 28 of 30
Used the small Phillips as an awl to loosen a knot in a strap on a piece of clothing that belongs to my little girl
it worked a treat and undid the knot very well 
<a href="https://flic.kr/p/2aqoCL5" target="_blank" rel="noopener noreferrer"><img src="https://farm2.staticflickr.com/1948/44251915484_f8b0194b57_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>2018-09-28_12-25-41 by Poncho 65, on Flickr
-
September Storm:
I was quite enamoured with Zoidberg's lanyard and big-boy lanyard ring attachment system.....so I made one for myself.

I think Z's split ring does help--the clearance of the thin split ring is better than that of the thicker paracord. However, with Zoidberg's modification, the Wave can just be removed from the lanyard and used "off leash". Obviously this has both advantages and potential disadvantages, but I like this system oveerall and will give this a try for a bit. Might try making a shorter lanyard. This current one--probably a bit longer than Z's--is longer than necessary.

-
@ReamerPunch said:
:o
My screws are fine, but the pivot is a bit tighter since all that wire cutting I did the other day.
It could be worse, considering your screw broke, so I am fine with my pivot. I am not fine with broken screws.If I ever have a screw break, I will ask for a replacement. The screws and wire cutters are not excluded from the warranty, so I expect a replacement.
Have you contacted LM about the screw? It would be interesting to see what they say. Will they replace it or just tell you to buy a new set?
Its a bit of challenge on LM warranty on my side.. Long story.. Not their fault.. I had removed the screw before a few days ago.. It was ok-ish when I put them back so I didn't think that they will loosen up..
I got too engrossed in the wire cutting that I didn't realise they came loose.. I have spare screw.. So thats OK. No losses here.It really really bothers me when the pliers tighten up on pressure. So for me in this case, it's either a break it in, or break it kind of situation.. I am an OCD when it comes to pliers..
-
Yes, the pliers tightening up annoyed the hell out of me on the Wave plus and the Rebar!!!
-
@Sam Lim said:
I broke my screw today..
This was the "new" pliers that I was trying to break in a few day ago with the spring... I was rather desperate to get it looser as I found out it suffers from the "hard squeeze tight pivot syndrome".... I cut a whole bunch of cloth hanger today in my final bid to solve this issue. Very unfortunately.. I didn't realise that my screw had come loose.. The screw snapped.. Half the screw was broken in the pliers. Was able to get it out eventually.. Lucky me..
Check your screws people! And use some form of lock tight in them!
Btw, I had somewhat relieved myself from the challenge a few days ago when I stopped posting pictures. :P 30 days is a challenge too long for me! I missed my other stuffs...

Thanks for the warning Sam

Sorry to hear that you couldn’t finish the challenge
It's actually a relieve..
at least for me.. Not that it's not a good/capable tool, it remains one of my favourite. Just that my love are just spread all over the place.. :DGood luck for everyone on the challenge! 2 more days to go! On my timezone.

-
@Jaypeebee said:
Yes, the pliers tightening up annoyed the hell out of me on the Wave plus and the Rebar!!!Honestly mine is now ALOT better when I first started. I seriously think it's a defect and not about using it enough that it will go away. It seems to me like the internals of the pivot area are out of alignment. Look at your dead pivot side. Are they totally flushed? They should. If it not, I would think the alignment have shifted like mine.
-
Day 28 <<-
Today I've used the Wave's pliers and Phillips bit to remove the batteries from a broken cheapish RC plane. The old style wire cutters had no trouble with those tiny stranded wires





-
@Sam Lim said:
Yes, the pliers tightening up annoyed the hell out of me on the Wave plus and the Rebar!!!
Honestly mine is now ALOT better when I first started. I seriously think it's a defect and not about using it enough that it will go away. It seems to me like the internals of the pivot area are out of alignment. Look at your dead pivot side. Are they totally flushed? They should. If it not, I would think the alignment have shifted like mine.
Yes, mine are better through use, not perfect yet though! The Rebar, I worked some grinding paste into the pivot and worked it for a while then flushed it out and lubricated it, they are perfect now!
-
Day 28/30
Today i didnt find any true use for my Wave, used Wave file to trim my finger nail. No action pic but took pic later in park.
<a href="https://flic.kr/p/28KYUZs" target="_blank" rel="noopener noreferrer"><img src="https://farm2.staticflickr.com/1909/43160903780_7432985d6a_b.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
Only Tools Matters
-
Hello
Just pinching somebody else's slogan but if the cap fits wear it I say.
Happy day 28
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
