Wave pocket clip on a Rebar (proof of concept)
-
Why did you need a Fuse pivot?
In which direction/s is the wiggle?I may have an idea, but just want to understand these two before sharing it
-
Thanks for thinking along 50ft-trad. The Wave pocket clip's end slips under the side lug of the handle in the pic, so I needed a bit (ca 1 mm) of extra space on the pivot's length for that. The wiggle is around the pivot's axis... I have briefly thought of welding, until I realised that I wouldn't be able to extract or insert pivots or their screws.
Edit: ... unless I made a hole the size of a pivot head in the clip. Kind of defeats the purpose.
-
@Dutch_Tooler said:
The Wave pocket clip's end slips under the side lug of the handle in the pic, so I needed a bit of extra space for that. The wiggle is around the pivot's axis... I have briefly thought of welding, until I realised that I wouldn't be able to extract or insert pivots or their screws.Edit: ... unless I made a hole the size of a pivot head in the clip. Kind of defeats the purpose.
It's a while since I handled or dismantled a Rebar, so that's not really helping me. I'll offer my idea forwards anyway, and even if it doesn't 100% solve it, it might give you enough food for thought to fix it.
Gimme a few minutes to sketch it up, and write an explanation...

-
Thanks for thinking along with me

-
I hope you get it to work D_T

Unfortunately I haven’t got a Rebar
Otherwise I would of had a look for youGood luck and hope you will
find a way of getting it to work

-
Thanks Wspeed

Detail pic...

-
Ok, here goes... before I get into the "how to", I'm going to make a couple of assumptions. If these are wrong, let me know...
Assumptions:
a) The Rebar pivot is a flanged spindle with screw (pic 1), rather than a barrel threaded at both ends and two screws. If the pivot is the double ended barrel, you will need to Loctite/superglue one of the pins in to make it like my sketch.
b) The "tang" of the clip takes up the space of one of the tools, but is thinner than a tool tang. If that is the case, stack the tools that you want to put in that handle, including the washers, and measure the height. Also measure the thickness of the clip tang, and determine what washers are needed to build this up to the correct tool stack height for proper tensioning. You need to do this first, as with the method I'm going to offer, the clip is the last thing to be fitted.
c) As removing the clip would leave the remaining inner tools sloppy, the clip will need to be left on permanently.Method:
-
Strip the handle down, and drill a small hole which intersects the radius at which the spindle flange would sit (pic 2)
-
Peen a small piece of brass rod into this hole, just as you would peed a Swiss knife mod, but ensure that the dome head is prominent on both internal and external faces.
-
Prior to assembly, grind and file a small notch on spindle flange and clip to coincide with the peened button (pic 3). This will act as a key to prevent rotation of both spindle and clip. Make sure the clip is a very close fit, to eliminate and side to side wiggle. The flange notch isn't as critical.
-
Insert the spindle into the handle, and load the tool stack and all the washers. Locate to spindle notch onto the key, and locate the end of the spindle into the hub on the opposite handle. Insert the screw, and tighten it just enough to hold the end of the spindle in the hub. Slide the clip into position, and nip up the screw. You might need to insert a small flat screwdriver under the clip, just to hold the flange on the key.
How does that sound?
NOTE: this uses the original Rebar pivot.



-
-
I like your idea 50ft

-
Thanks Speedy. Hopefully DT will find it useful

-
That is a very well thought out method, thanks 50ft
It would certainly work well 
During my late afternoon stroll I have had an idea or two myself. Somewhat different to yours, and a tad less solid, but it would allow removing the clip without trace if I tire of it.
I'll illustrate it at the hand of a 9mm / 5mm washer but I'll need to source or fashion one with 4.8 mm inner dia. to fit exactly over the pivot with as little play as possible.-
I'd thin the washer to about half thickness over an area corresponding to the blue shaded area in the pic, so that the remaining thicker portion fits exactly in the opening in the clip.
-
Then I'd bend the two ends of the clip up so as to radially constrain the washer when the latter is mounted on top of the clip.
-
The washer comes in after the last tool with the thicker remaining portion pointing outwards, then I pre-assemble the handle tools and pivot without tightening and without clip as yet.
-
Then I slip the clip in, which fits over the remaining thicker portion of the washer and catches it when the pivot is tightened.
That's the theory, at least...

-
-
Another option that u can explore is using the little washer found on the TTI at the lanyard pivot. This way you can insert and remove as required. Regarding the wobble, hmm.. I am thinking maybe filing either the clip or the frame a little might allow the feet of the clip to sit into the frame... Never try never know...




-
Excellent ideas guys

Can’t wait to see what will work best
I just wish all MTs would have a
Pocket clip that could be attached
-
@Sam Lim said:
Another option that u can explore is using the little washer found on the TTI at the lanyard pivot. This way you can insert and remove as required. Regarding the wobble, hmm.. I am thinking maybe filing either the clip or the frame a little might allow the feet of the clip to sit into the frame... Never try never know...



That is a nice thought Sam... do you happen to have precise measurements of that washer? Failing that I'm more than prepared to fashion my own...
-
Sam, is that the washer at the retractable lanyard ring? If yes, it should be standard on Waves too. One wonders if they've maybe coincidentally have made that the same width as the slot in the pocket clip...?
-
@Dutch_Tooler said:
Sam, is that the washer at the retractable lanyard ring? If yes, it should be standard on Waves too. One wonders if they've maybe coincidentally have made that the same width as the slot in the pocket clip...?DT, yes that part is found at the lanyard ring but it's only available on the TTI/TI. Not on wave or even AL. Its a bushing to prevent the scales from collapsing the slot for the pocket clip. Wave uses a end cap. Charge AL uses something very different. Sorry I do not have a digital caliper to measure that.. According to my very wildly inaccurate eyeball gauge, its probably about 0.5mm thick..

-
Thanks Sam. I'll have a peek at how the Wave solves this sometimes this week. Stay tuned...
-
Wave end cap with integrated spacer for the pocket clip slot, seen in combination with the clip. The blue arrow points at a small tab integrated in the end cap as well. That tab also holds the clip's longer of the two ends. That, together with the lock notch and the slot, is what keeps the clip centered. All of that will need to be reproduced somehow...


-
Any idea on how to make one

-
JB Weld / epoxy putty?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login