Wave pocket clip on a Rebar (proof of concept)
-
That is a very well thought out method, thanks 50ft
It would certainly work well 
During my late afternoon stroll I have had an idea or two myself. Somewhat different to yours, and a tad less solid, but it would allow removing the clip without trace if I tire of it.
I'll illustrate it at the hand of a 9mm / 5mm washer but I'll need to source or fashion one with 4.8 mm inner dia. to fit exactly over the pivot with as little play as possible.-
I'd thin the washer to about half thickness over an area corresponding to the blue shaded area in the pic, so that the remaining thicker portion fits exactly in the opening in the clip.
-
Then I'd bend the two ends of the clip up so as to radially constrain the washer when the latter is mounted on top of the clip.
-
The washer comes in after the last tool with the thicker remaining portion pointing outwards, then I pre-assemble the handle tools and pivot without tightening and without clip as yet.
-
Then I slip the clip in, which fits over the remaining thicker portion of the washer and catches it when the pivot is tightened.
That's the theory, at least...

-
-
Another option that u can explore is using the little washer found on the TTI at the lanyard pivot. This way you can insert and remove as required. Regarding the wobble, hmm.. I am thinking maybe filing either the clip or the frame a little might allow the feet of the clip to sit into the frame... Never try never know...




-
Excellent ideas guys

Can’t wait to see what will work best
I just wish all MTs would have a
Pocket clip that could be attached
-
@Sam Lim said:
Another option that u can explore is using the little washer found on the TTI at the lanyard pivot. This way you can insert and remove as required. Regarding the wobble, hmm.. I am thinking maybe filing either the clip or the frame a little might allow the feet of the clip to sit into the frame... Never try never know...



That is a nice thought Sam... do you happen to have precise measurements of that washer? Failing that I'm more than prepared to fashion my own...
-
Sam, is that the washer at the retractable lanyard ring? If yes, it should be standard on Waves too. One wonders if they've maybe coincidentally have made that the same width as the slot in the pocket clip...?
-
@Dutch_Tooler said:
Sam, is that the washer at the retractable lanyard ring? If yes, it should be standard on Waves too. One wonders if they've maybe coincidentally have made that the same width as the slot in the pocket clip...?DT, yes that part is found at the lanyard ring but it's only available on the TTI/TI. Not on wave or even AL. Its a bushing to prevent the scales from collapsing the slot for the pocket clip. Wave uses a end cap. Charge AL uses something very different. Sorry I do not have a digital caliper to measure that.. According to my very wildly inaccurate eyeball gauge, its probably about 0.5mm thick..

-
Thanks Sam. I'll have a peek at how the Wave solves this sometimes this week. Stay tuned...
-
Wave end cap with integrated spacer for the pocket clip slot, seen in combination with the clip. The blue arrow points at a small tab integrated in the end cap as well. That tab also holds the clip's longer of the two ends. That, together with the lock notch and the slot, is what keeps the clip centered. All of that will need to be reproduced somehow...


-
Any idea on how to make one

-
JB Weld / epoxy putty?
-
@AimlessWanderer said:
JB Weld / epoxy putty?+1
Tested this out a while back and concluded that a dab of JB would be the go.
-
JB Weld / epoxy putty?
+1
Tested this out a while back and concluded that a dab of JB would be the go.
Thanks, I think I'll try that

Awesome new forum name AW (you realise it'll be shortened more often than not, right?)
-
JB Weld / epoxy putty?
+1
Tested this out a while back and concluded that a dab of JB would be the go.
Thanks, I think I'll try that

Awesome new forum name AW (you realise it'll be shortened more often than not, right?)
Thanks

Sure it'll be shortened. I'm happy with AW or Al, so if you're typing in the dark and hit a wrong key, there's double the chance of getting it right :D
-
Some old pics over here. /post/948856
Back then I also had a vague idea about milling a recess into the side of the large bit driver to hold the clip.
Down sides are not everyone has a large bit driver in their Rebar and having to remove the clip to use the driver. -

Nice breakfast read.
Ordered some JB Weld. Considering to use brass for a collar ring bridging the gap between the pivot and clip slot... thin flange to separate the clip cavity from the file... Time to set up the lathe (hot-bunks workspace slot with 3D printer - not enough space ::) :-)
I have a bit driver but not in that spot, that's where my Wave file resides.
-
Made some progress today.
I have made a better version of the collar ring you see in pic 1 - on that one I botched the inner bore, but you get the idea. Pic 2 shows where the better one sits on the pivot. Pics 3 and 4 show how the clip sits on and off the Rebar VX - yes, it's still removable in case I sheath carry.




-
However, I am not entirely happy - unfortunately there is quite some residual wobble around the pivot axis... see pics below for the extent

I fear that even making a small tab on the handle will not reduce this to zero as the tool lock is quite a bit narrower than the slot for it in the clip. I'll see whether I can live with this. After the Spirit challenge, of course



-
Thanks for showing your progress D_T

Is the lock tab cut out on the clip to big

-
What if you drill a hole on the Rebar handle, press fit/ Loctite a pin in, which also fit into the Wave clip slot?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login