Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Wave pocket clip on a Rebar (proof of concept)

Scheduled Pinned Locked Moved The Mod Squad
76 Posts 1 Posters 6.5k Views
  1. Home
  2. Tool Talk
  3. The Mod Squad
  4. Wave pocket clip on a Rebar (proof of concept)
Wave pocket clip on a Rebar (proof of concept)
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • AimlessWanderer Offline
    AimlessWanderer
    Posts: 17,518
    AimlessWanderer Offline
    AimlessWanderer
    wrote on last edited by
    #20 Quote Reply

      JB Weld / epoxy putty?

      1 Reply Last reply
      • zoidberg Offline
        zoidberg
        Posts: 38,161
        zoidberg Offline
        zoidberg
        wrote on last edited by
        #21 Quote Reply

          @AimlessWanderer said:
          JB Weld / epoxy putty?

          +1

          Tested this out a while back and concluded that a dab of JB would be the go.

          1 Reply Last reply
          • Dutch_Tooler Offline
            Dutch_Tooler
            Posts: 4,434
            Dutch_Tooler Offline
            Dutch_Tooler
            wrote on last edited by
            #22 Quote Reply

              @zoidberg said:

              @AimlessWanderer said:

              JB Weld / epoxy putty?

              +1

              Tested this out a while back and concluded that a dab of JB would be the go.

              Thanks, I think I'll try that :cheers:

              Awesome new forum name AW (you realise it'll be shortened more often than not, right?)

              1 Reply Last reply
              • AimlessWanderer Offline
                AimlessWanderer
                Posts: 17,518
                AimlessWanderer Offline
                AimlessWanderer
                wrote on last edited by
                #23 Quote Reply

                  @Dutch_Tooler said:

                  @zoidberg said:

                  @AimlessWanderer said:

                  JB Weld / epoxy putty?

                  +1

                  Tested this out a while back and concluded that a dab of JB would be the go.

                  Thanks, I think I'll try that :cheers:

                  Awesome new forum name AW (you realise it'll be shortened more often than not, right?)

                  Thanks :salute:

                  Sure it'll be shortened. I'm happy with AW or Al, so if you're typing in the dark and hit a wrong key, there's double the chance of getting it right :D

                  1 Reply Last reply
                  • zoidberg Offline
                    zoidberg
                    Posts: 38,161
                    zoidberg Offline
                    zoidberg
                    wrote on last edited by
                    #24 Quote Reply

                      Some old pics over here. /post/948856

                      Back then I also had a vague idea about milling a recess into the side of the large bit driver to hold the clip.
                      Down sides are not everyone has a large bit driver in their Rebar and having to remove the clip to use the driver.

                      1 Reply Last reply
                      • Dutch_Tooler Offline
                        Dutch_Tooler
                        Posts: 4,434
                        Dutch_Tooler Offline
                        Dutch_Tooler
                        wrote on last edited by Dutch_Tooler
                        #25 Quote Reply

                          :cheers:

                          Nice breakfast read.

                          Ordered some JB Weld. Considering to use brass for a collar ring bridging the gap between the pivot and clip slot... thin flange to separate the clip cavity from the file... Time to set up the lathe (hot-bunks workspace slot with 3D printer - not enough space ::) :-)

                          I have a bit driver but not in that spot, that's where my Wave file resides.

                          1 Reply Last reply
                          • Dutch_Tooler Offline
                            Dutch_Tooler
                            Posts: 4,434
                            Dutch_Tooler Offline
                            Dutch_Tooler
                            wrote on last edited by
                            #26 Quote Reply

                              Made some progress today.

                              I have made a better version of the collar ring you see in pic 1 - on that one I botched the inner bore, but you get the idea. Pic 2 shows where the better one sits on the pivot. Pics 3 and 4 show how the clip sits on and off the Rebar VX - yes, it's still removable in case I sheath carry.

                              913201818625.jpg

                              91320181876.jpg

                              913201818723.jpg

                              913201818741.jpg

                              1 Reply Last reply
                              • Dutch_Tooler Offline
                                Dutch_Tooler
                                Posts: 4,434
                                Dutch_Tooler Offline
                                Dutch_Tooler
                                wrote on last edited by Dutch_Tooler
                                #27 Quote Reply

                                  However, I am not entirely happy - unfortunately there is quite some residual wobble around the pivot axis... see pics below for the extent :facepalm:

                                  I fear that even making a small tab on the handle will not reduce this to zero as the tool lock is quite a bit narrower than the slot for it in the clip. I'll see whether I can live with this. After the Spirit challenge, of course :angel:

                                  913201818823.jpg

                                  91320181889.jpg

                                  1 Reply Last reply
                                  • Wspeed Offline
                                    Wspeed
                                    Posts: 76,225
                                    Wspeed Offline
                                    Wspeed
                                    wrote on last edited by
                                    #28 Quote Reply

                                      Thanks for showing your progress D_T :cheers:
                                      Is the lock tab cut out on the clip to big :think: :tu:

                                      1 Reply Last reply
                                      • chrono Offline
                                        chrono
                                        Posts: 1,313
                                        chrono Offline
                                        chrono
                                        wrote on last edited by
                                        #29 Quote Reply

                                          What if you drill a hole on the Rebar handle, press fit/ Loctite a pin in, which also fit into the Wave clip slot?

                                          1 Reply Last reply
                                          • AimlessWanderer Offline
                                            AimlessWanderer
                                            Posts: 17,518
                                            AimlessWanderer Offline
                                            AimlessWanderer
                                            wrote on last edited by
                                            #30 Quote Reply

                                              @Dutch_Tooler said:
                                              However, I am not entirely happy - unfortunately there is quite some residual wobble around the pivot axis... see pics below for the extent :facepalm:

                                              I fear that even making a small tab on the handle will not reduce this to zero as the tool lock is quite a bit narrower than the slot for it in the clip. I'll see whether I can live with this. After the Spirit challenge, of course :angel:

                                              Wow! That's a lot of wobble!

                                              Can you tell by feel, if the wobble is on the pivot bushing you made, or on the cut out for the lock bar?

                                              1 Reply Last reply
                                              • Dutch_Tooler Offline
                                                Dutch_Tooler
                                                Posts: 4,434
                                                Dutch_Tooler Offline
                                                Dutch_Tooler
                                                wrote on last edited by Dutch_Tooler
                                                #31 Quote Reply

                                                  Bit of both, actually. On reflection I think I might try to add the side tab mentioned earlier, but I'd prefer this to be of metal (more wear-proof surface) and will probably have to epoxy it to the handle. Not sure how that will hold though, as one could inadvertently apply a lot of torque via the long arm of the clip... :think:

                                                  Alternatively, or in addition, I could instead of a collar ring, make something that matches the clip slot cutout exactly in planform. I could in theory use the flat sides of the pivot to keep this object rotationally fixed somehow, but the pivot-to-handle tolerances in rotation are not very tight so some wobble will remain even so... apart from the problem with fashioning a hole with flat sides, of course.

                                                  1 Reply Last reply
                                                  • Dutch_Tooler Offline
                                                    Dutch_Tooler
                                                    Posts: 4,434
                                                    Dutch_Tooler Offline
                                                    Dutch_Tooler
                                                    wrote on last edited by
                                                    #32 Quote Reply

                                                      @Wspeed said:
                                                      Thanks for showing your progress D_T :cheers:
                                                      Is the lock tab cut out on the clip to big :think: :tu:

                                                      A little bit. I guess the lock is a little bit slimmer on the Rebar than on the Wave (?)

                                                      1 Reply Last reply
                                                      • Dutch_Tooler Offline
                                                        Dutch_Tooler
                                                        Posts: 4,434
                                                        Dutch_Tooler Offline
                                                        Dutch_Tooler
                                                        wrote on last edited by
                                                        #33 Quote Reply

                                                          @chrono said:
                                                          What if you drill a hole on the Rebar handle, press fit/ Loctite a pin in, which also fit into the Wave clip slot?

                                                          Hmm... thanks - I'd prefer to not drill into the handles, if possible... :surrender:

                                                          1 Reply Last reply
                                                          • Wspeed Offline
                                                            Wspeed
                                                            Posts: 76,225
                                                            Wspeed Offline
                                                            Wspeed
                                                            wrote on last edited by
                                                            #34 Quote Reply

                                                              @Dutch_Tooler said:

                                                              @chrono said:

                                                              What if you drill a hole on the Rebar handle, press fit/ Loctite a pin in, which also fit into the Wave clip slot?

                                                              Hmm... thanks - I'd prefer to not drill into the handles, if possible... :surrender:

                                                              No I am not keen on that as well
                                                              As it voids the warranty :think:
                                                              I like it if the MT can be made to original spec again :tu:

                                                              1 Reply Last reply
                                                              • Dutch_Tooler Offline
                                                                Dutch_Tooler
                                                                Posts: 4,434
                                                                Dutch_Tooler Offline
                                                                Dutch_Tooler
                                                                wrote on last edited by
                                                                #35 Quote Reply

                                                                  The problem seems to lie with the indent in the longer of the clip's insert legs, which on the Wave has a matching stop in the handle, but not on the Rebar, see the rectangular cut-out left over near the clip insert leg's end in Pic 1.
                                                                  I can almost make the wobble disappear by inserting an x-Acto chisel blade in that space, Pics 2 and 3. I simply need to find something metallic to fill that hole and which can be fixed in place, preferably removably.

                                                                  9142018141623.jpg

                                                                  9142018141653.jpg

                                                                  914201814179.jpg

                                                                  9142018141639.jpg

                                                                  1 Reply Last reply
                                                                  • Wspeed Offline
                                                                    Wspeed
                                                                    Posts: 76,225
                                                                    Wspeed Offline
                                                                    Wspeed
                                                                    wrote on last edited by
                                                                    #36 Quote Reply

                                                                      I can’t think of anything at the moment :think:

                                                                      1 Reply Last reply
                                                                      • AimlessWanderer Offline
                                                                        AimlessWanderer
                                                                        Posts: 17,518
                                                                        AimlessWanderer Offline
                                                                        AimlessWanderer
                                                                        wrote on last edited by
                                                                        #37 Quote Reply

                                                                          Ahh! I think I see the issue.

                                                                          Am I right in thinking a spacer piece along the inner wall, could brace that abutment lip against the rolled edge of the handle. Something like a piece of the magnetic strip off the back of fridge magnets? Are the handles magnetic?

                                                                          The only other thing I can think of, is TIG welding that area on the clip, to build it up so it contacts directly with the underside of the rolled edge.

                                                                          1 Reply Last reply
                                                                          • Dutch_Tooler Offline
                                                                            Dutch_Tooler
                                                                            Posts: 4,434
                                                                            Dutch_Tooler Offline
                                                                            Dutch_Tooler
                                                                            wrote on last edited by Dutch_Tooler
                                                                            #38 Quote Reply

                                                                              Yup. I'd been thinking along these lines too, AW - unfortunately the handles are stainless steel, i.e. non-magnetic. TIG welding would probably work, but I lack the equipment (or the skills, for that matter).

                                                                              Current thinking is to make a filler that carries that stop tab (itself pretty awkwardly formed) and keeps it abutted against the rolled handle edge, and epoxied into the handle just inside of the rolled edge where the handle is widest and where it won't interfere with the clip. I'm a little bit worried that handle twist may make that a futile exercise, though.

                                                                              Just building up the stop tab from JB-Weld appears to me to be too weak to start with, it would wear out quickly even if it stayed put, which it might not for long given adverse loads on inserting or turning the clip...

                                                                              1 Reply Last reply
                                                                              • AimlessWanderer Offline
                                                                                AimlessWanderer
                                                                                Posts: 17,518
                                                                                AimlessWanderer Offline
                                                                                AimlessWanderer
                                                                                wrote on last edited by
                                                                                #39 Quote Reply

                                                                                  With all this "add a bit here", and "add a bit there", would it not now (now you can see what needs to go where, and why) be easier to make a custom clip, using the Wave one as a template, but modifying the tang shape to suit the pivot and handle form? All that's needed is a bit of stainless, a vice, a hammer, and a dremel.

                                                                                  1 Reply Last reply

                                                                                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                                                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                                                  With your input, this post could be even better 💗

                                                                                  Register Login

                                                                                  • 1
                                                                                  • 2
                                                                                  • 3
                                                                                  • 4
                                                                                  1. Home
                                                                                  2. Tool Talk
                                                                                  3. The Mod Squad
                                                                                  4. Wave pocket clip on a Rebar (proof of concept)
                                                                                  Reply
                                                                                  • Reply as topic
                                                                                  Log in to reply
                                                                                  COMMUNITY LINKS
                                                                                  EDC-TV SAKWiki GearFeed SAKSelector
                                                                                  Operational Funds

                                                                                  Help us keep the Unworkable working!

                                                                                  Make A Donation
                                                                                  November Goal: $300.00
                                                                                  Due Date: Nov 30
                                                                                  Total Receipts: $0.00
                                                                                  Below Goal: $300.00
                                                                                  0% funded
                                                                                  • Login

                                                                                  • Don't have an account? Register

                                                                                  • Login or register to search.
                                                                                  • First post
                                                                                    Last post
                                                                                  0