Wave pocket clip on a Rebar (proof of concept)
-
Any idea on how to make one

-
JB Weld / epoxy putty?
-
@AimlessWanderer said:
JB Weld / epoxy putty?+1
Tested this out a while back and concluded that a dab of JB would be the go.
-
JB Weld / epoxy putty?
+1
Tested this out a while back and concluded that a dab of JB would be the go.
Thanks, I think I'll try that

Awesome new forum name AW (you realise it'll be shortened more often than not, right?)
-
JB Weld / epoxy putty?
+1
Tested this out a while back and concluded that a dab of JB would be the go.
Thanks, I think I'll try that

Awesome new forum name AW (you realise it'll be shortened more often than not, right?)
Thanks

Sure it'll be shortened. I'm happy with AW or Al, so if you're typing in the dark and hit a wrong key, there's double the chance of getting it right :D
-
Some old pics over here. /post/948856
Back then I also had a vague idea about milling a recess into the side of the large bit driver to hold the clip.
Down sides are not everyone has a large bit driver in their Rebar and having to remove the clip to use the driver. -

Nice breakfast read.
Ordered some JB Weld. Considering to use brass for a collar ring bridging the gap between the pivot and clip slot... thin flange to separate the clip cavity from the file... Time to set up the lathe (hot-bunks workspace slot with 3D printer - not enough space ::) :-)
I have a bit driver but not in that spot, that's where my Wave file resides.
-
Made some progress today.
I have made a better version of the collar ring you see in pic 1 - on that one I botched the inner bore, but you get the idea. Pic 2 shows where the better one sits on the pivot. Pics 3 and 4 show how the clip sits on and off the Rebar VX - yes, it's still removable in case I sheath carry.




-
However, I am not entirely happy - unfortunately there is quite some residual wobble around the pivot axis... see pics below for the extent

I fear that even making a small tab on the handle will not reduce this to zero as the tool lock is quite a bit narrower than the slot for it in the clip. I'll see whether I can live with this. After the Spirit challenge, of course



-
Thanks for showing your progress D_T

Is the lock tab cut out on the clip to big

-
What if you drill a hole on the Rebar handle, press fit/ Loctite a pin in, which also fit into the Wave clip slot?
-
@Dutch_Tooler said:
However, I am not entirely happy - unfortunately there is quite some residual wobble around the pivot axis... see pics below for the extent
I fear that even making a small tab on the handle will not reduce this to zero as the tool lock is quite a bit narrower than the slot for it in the clip. I'll see whether I can live with this. After the Spirit challenge, of course

Wow! That's a lot of wobble!
Can you tell by feel, if the wobble is on the pivot bushing you made, or on the cut out for the lock bar?
-
Bit of both, actually. On reflection I think I might try to add the side tab mentioned earlier, but I'd prefer this to be of metal (more wear-proof surface) and will probably have to epoxy it to the handle. Not sure how that will hold though, as one could inadvertently apply a lot of torque via the long arm of the clip...

Alternatively, or in addition, I could instead of a collar ring, make something that matches the clip slot cutout exactly in planform. I could in theory use the flat sides of the pivot to keep this object rotationally fixed somehow, but the pivot-to-handle tolerances in rotation are not very tight so some wobble will remain even so... apart from the problem with fashioning a hole with flat sides, of course.
-
What if you drill a hole on the Rebar handle, press fit/ Loctite a pin in, which also fit into the Wave clip slot?
Hmm... thanks - I'd prefer to not drill into the handles, if possible...

No I am not keen on that as well
As it voids the warranty
I like it if the MT can be made to original spec again
-
The problem seems to lie with the indent in the longer of the clip's insert legs, which on the Wave has a matching stop in the handle, but not on the Rebar, see the rectangular cut-out left over near the clip insert leg's end in Pic 1.
I can almost make the wobble disappear by inserting an x-Acto chisel blade in that space, Pics 2 and 3. I simply need to find something metallic to fill that hole and which can be fixed in place, preferably removably.



-
I can’t think of anything at the moment

-
Ahh! I think I see the issue.
Am I right in thinking a spacer piece along the inner wall, could brace that abutment lip against the rolled edge of the handle. Something like a piece of the magnetic strip off the back of fridge magnets? Are the handles magnetic?
The only other thing I can think of, is TIG welding that area on the clip, to build it up so it contacts directly with the underside of the rolled edge.
-
Yup. I'd been thinking along these lines too, AW - unfortunately the handles are stainless steel, i.e. non-magnetic. TIG welding would probably work, but I lack the equipment (or the skills, for that matter).
Current thinking is to make a filler that carries that stop tab (itself pretty awkwardly formed) and keeps it abutted against the rolled handle edge, and epoxied into the handle just inside of the rolled edge where the handle is widest and where it won't interfere with the clip. I'm a little bit worried that handle twist may make that a futile exercise, though.
Just building up the stop tab from JB-Weld appears to me to be too weak to start with, it would wear out quickly even if it stayed put, which it might not for long given adverse loads on inserting or turning the clip...
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login