Brass Rod NOW!!!
-
Whew, alright, it's already put together, at least I put the layers all together on the pins, but now what? Last time one side was already peened, but not so now. Right now it's just 4 rods sticking through the knife holding it together. What next?
Btw, a little teaser, it's leftover Champ parts, so I made a pseudo Lumberjack (of sorts):
Layer 1: Large blade, small blade, corkscrew
Layer 2: Wood saw, chiselSort of a woodworker knife, all cutting blades (save for the corkscrew... I guess it's meant to screw into cork, a sort of wood :P )
Hopefully I can find my dang ball pien hammer, I know it's around this room somewhere... -
@Ben X said:
Whew, alright, it's already put together, at least I put the layers all together on the pins, but now what? Last time one side was already peened, but not so now. Right now it's just 4 rods sticking through the knife holding it together. What next?Btw, a little teaser, it's leftover Champ parts, so I made a pseudo Lumberjack (of sorts):
Layer 1: Large blade, small blade, corkscrew
Layer 2: Wood saw, chiselSort of a woodworker knife, all cutting blades (save for the corkscrew... I guess it's meant to screw into cork, a sort of wood :P )
Hopefully I can find my dang ball pien hammer, I know it's around this room somewhere...This is where Gareth and I differ in approach (both work mind). I like to cut the brass 1 to 1.5mm proud of the bushing either side and then then a few taps to one side, turn the knife over and a few taps to the other, repeat 'till right. Gareth likes to take a longer bit of brass and dome one end first, pop it in place, cut to size and then peen from that side. (I'm sure he'll correct me if I'm remembering that wrong). Either way it really isn't any more difficult than working on a knife that already has been factory peened on one side.
Really, you'll be fine

Neil
-
Someone else (I think Spork?) leaves part of the rod unmilled, so that he has a thicker portion on one side. Won't work if you have the right size brass though...
-
@Ben X said:
Whew, alright, it's already put together, at least I put the layers all together on the pins, but now what? Last time one side was already peened, but not so now. Right now it's just 4 rods sticking through the knife holding it together. What next?
Btw, a little teaser, it's leftover Champ parts, so I made a pseudo Lumberjack (of sorts):
Layer 1: Large blade, small blade, corkscrew
Layer 2: Wood saw, chiselSort of a woodworker knife, all cutting blades (save for the corkscrew... I guess it's meant to screw into cork, a sort of wood :P )
Hopefully I can find my dang ball pien hammer, I know it's around this room somewhere...This is where Gareth and I differ in approach (both work mind). I like to cut the brass 1 to 1.5mm proud of the bushing either side and then then a few taps to one side, turn the knife over and a few taps to the other, repeat 'till right. Gareth likes to take a longer bit of brass and dome one end first, pop it in place, cut to size and then peen from that side. **(I'm sure he'll correct me if I'm remembering that wrong). ** Either way it really isn't any more difficult than working on a knife that already has been factory peened on one side.
Really, you'll be fine

Neil
Don't worry you got it right. :D .
-
That's definitely the tricky bit for me anyway. I tend to use Neil's method, leaving a couple of mm over on each side, but then I take a dremmel sanding bit to each end and flatten them down to about 1mm above the bushings. Then, I peen with a ball pein hammer, using a miniature anvil I picked up cheaply to form a nice neat finish.
All different routes to the same end product

-
Actually Dave makes a good point. Before you start peening make sure you have a nice flat end on the pin. If you have just clipped it to length with snips then it will be horribly uneven. Take a few minutes to flatten the end and the result will be much nicer and , more importantly, easier. I simply use a file but if you've got a Dremel type tool that should make life even simpler.
-
Gareth and I are doing it correctly...I have no ideal what Neil and the Bees are doing
:o :D
-
Just kidding with you Neil. :D
One reason I like to start with longer pins is that I don't use any type of assembly jig and it gives me a little bit of leverage when lining up the holes by hand.
-
I always jig 
I am not manly enough to shove the springs about without assistance. Not without blood loss anyway :ahhh
Neil
-
Good to know I'm doing something right. ;)
-
Don't you find that peening from both sides will bend pins sometimes...in knives 4-layers and up that is.
-
I do it by hand. Strong, manly hands. :D
-
@SporK said:
Don't you find that peening from both sides will bend pins sometimes...in knives 4-layers and up that is.Having only girly hands
I've moved to using little girly hammers.Yes, I've bent pins in the past but now I just take an obscene amount of time over it with teeny, tiny, minuscule, feminine tools. Suits my demeanour

Your all just a bunch of ham fisted apes :P
Neil
-
I try to think of those sort of occasions as "learning experiences". Then I generally pick the whole lot up and throw it with considerable force across the garage. Often this will result in severe damage to the knife, so I will swear a lot and give up for the evening> If I'm lucky I'll have to walk past the remains on the way out and can give the thing one last Colorful Enunciationing kick.
Calm.
-
@DaveK said:
I try to think of those sort of occasions as "learning experiences". Then I generally pick the whole lot up and throw it with considerable force across the garage. Often this will result in severe damage to the knife, so I will swear a lot and give up for the evening> If I'm lucky I'll have to walk past the remains on the way out and can give the thing one last Colorful Enunciationing kick.Calm.
Yikes! I do stuff like that all the time when I'm working on stubborn (cough American cough) cars, but usually big heavy metal parts can handle a little frustration :P I really don't favor carrying anything over 3 layers, so hopefully I will never run into that problem, but it's good to know to be careful of that. Is that because brass is a little softer than what Vic uses? That silver nickel or whatever the heck SwissBianco is always insisting is superior? :P
-
Wow I can't believe in less than three days this thread went from "where can I get brass rod?" to "Here is my completed second mod!" Thanks everyone, I hammered this sucker together tonight and it is lovely! I am tempted to keep it for myself, but it will probably end up a gift for someone. It would make a great camping or landscaping/gardening knife. Now it's time to start dreaming and acquire donors, this was about all I could do in the way of a 2 layer with the leftover parts from a champ. I would've made a Scientist if I had a combo tool :P

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login