New Charge Plus issues
-
I just checked my Charge ALX BO and will check the other charges I have. The ALX as most, if not all, my tools favors one side to close. The plier head only very slightly, I repeat, very slightly rubs when closing. I had to close with my ear next to the tool. The saw rubs when closing and is both audible and felt. The main blade has very slight up and down movement.
My Swisstool plier rubs very slightly. All tools have very slight movement when opened in the locked position. Mind you its only noticeable when pushing the tools.
My Skeletool CXs main blade is rock solid.
I checked my Sprirt and no plier rub at all and all tools rock solid. I believe the uneven handles was addressed by Victorionx as "its part of the design". I could be wrong on that
.I'll take a look in a moment at the rest of my Charges. Mine are all going to be the oder versions Ti, AL, SLV, TTi but I'll check.
-
My new Surge has the same problem the pliers rub on
the handles and this really shows up on the BO pliers ??? -
When you guys are talking about the plier rubbing you mean against the side of the handle right?
Because my Wave + (and my Spirit) don't have that either, I was talking about the plier tip on the inside tools (see my loooong post above ;)).
-
@Wspeed said:
My new Surge has the same problem the pliers rub on
the handles and this really shows up on the BO pliers ???My stainless Surge has the same problem real bad, but since it's a user I don't really care...
My BO Surge on the other hand is not a user, but I haven't opened and closed it enough to have rub markings on the plier head (that is if he should rub in the first place).
-
Charge SLV. Plier head rub. None. Blade play. No. Serrated. None. File rub. Yes. Saw rub. Very slightly.
Charge ALX. Plier head rub. Very slightly near the pivot. Blade play. None. Serrated. very slightly. File rub. yes. Saw rub. No.
Charge Ti, Plier head rub. None. Blade play. No. Serrated. No. File rub. yes. Saw rub. No.
Charge AL. Plier head rub. Yes near pivot. Blade play. None. Serrated. None. File rub. None. Saw rub. Very Slightly.
I'll check my TTi later as its in my vehicle.
I've highlighted my ALX BO earlier.
Hope this helps.

-
Sorry OCD peeps. 
-
@Aloha007 said:
Charge SLV. Plier head rub. None. Blade play. No. Serrated. None. File rub. Yes. Saw rub. Very slightly.Charge ALX. Plier head rub. Very slightly near the pivot. Blade play. None. Serrated. very slightly. File rub. yes. Saw rub. No.
Charge Ti, Plier head rub. None. Blade play. No. Serrated. No. File rub. yes. Saw rub. No.
Charge AL. Plier head rub. Yes near pivot. Blade play. None. Serrated. None. File rub. None. Saw rub. Very Slightly.
I'll check my TTi later as its in my vehicle.
I've highlighted my ALX BO earlier.
Hope this helps.
It seems like there is still a market for older Charges. I recently bought a Charge plus, but not open the packaging yet. My newest dated Charge before the Plus is a Red Cross Charge, whose file rubs more prevalently than older models. Just wonder when the QC became lax at the factory.
A question, is it possible to put a Charge Plus head (non-CC) on an old Charge TTi?
-
For collectors the older ones will always be collectable, even with the release of the camo charges. Thats my take.
-
@Top-Gear-24 said:
When you guys are talking about the plier rubbing you mean against the side of the handle right?Because my Wave + (and my Spirit) don't have that either, I was talking about the plier tip on the inside tools (see my loooong post above ;)).
For what I've described, YES.
-
@ chrono. "A question, is it possible to put a Charge Plus head (non-CC) on an old Charge TTi?"
I dont see why the pliers wouldn't be interchangeable
. However what others have done is use Rebar plier head prior to the release of the + models. Heck, I would imagine Rebar plier head is on the + models anyway 
-
The uneven handles on many SwissTool Spirits cannot be part of thew design. I got one with noticeably misaligned handles. Then I went to another store, and none of the exact same model had any misalignment. A Victorinox rep here in Israel had said "send it in," but let me know that I may get a blister pack replacement. And the misalignment may be in the new tool. He couldn't open the blister pack. I will admit that the use of the tool is not affected. I kept it.
Victorinox multitools usually have a near-perfection in their fit and finish, and crooked handles bothered me. But I am over it now. A little bit less idealistic. I just wonder what they pay QC engineers to do if they let crooked handles out of the factory in large numbers. Let's face it, much as many of use actually use multitools, they are also tactile and visual mechanical pleasures. Or as some would say, toys (...but sophisticated toys).

Back to the Charge...
-
My 07 TTI and 08 AL are absolutely PERFECT.
Was I just lucky or was QC way better 10 years ago?
-
@Mechanickal said:
My 07 TTI and 08 AL are absolutely PERFECT.Was I just lucky or was QC way better 10 years ago?
Probably

-
@Top-Gear-24 said:
I just checked 3 or 4 of my Leatherman Tools (the ones I have nearby while sitting behind the PC) and guess what, they all have the plier scraping against the bit ...The reason why I've never noticed this before seems to be that it's something that (mostly) happens when you pay close attention to closing the tool.
I mean, when I close the tool fast like I would during real use, I feel nothing, maybe the plier is still slightly scraping the bit, but if so, it happens very smooth and unnoticeable. But when I close the tool very slow, one handle at a time, leaving the side with the bit for last, putting the plierhead in the handle and then close up the tool real slow, I can see it scraping very hard, right up to the point that I have to apply extra force because the tip of the plierhead gets stuck on the edge of the bit.
Just checked what happens when you close the other handle last and very slow, and it scrapes the tools on the other side as well, but it's not so noticeable since the tools on the other side don't have the "edge" that the bit has, and they are all stainless, so you don't see the scraping line as good as on the black bit.
All of this on a tool that I use on a daily base, and on which I never noticed something wrong.
So I wonder; if you just close the tool like you would during real use, without paying attention to the plierhead sliding inside the handle and the scraping and all that, is it still noticeable enough to be a problem ? please, don't get me wrong, I'm not saying there isn't a problem on your Charge, but since I can't handle your tool the second best thing I could do was check some of mine, and this is what I noticed on them.
P.S.: I just checked one of my Spirits and guess what, the plierhead also scrapes while closing the handles, but ... Since the Spirit has outside opening tools the smart Vic engineers put in a slope for the plierhead to slide on until it is fully closed.
Great description of exactly what mine does.
I exchanged the bit over to a fresh (unscraped) side and quickly snapped the tool closed a few times like I didn't have a care in the world. Interestingly the new scrape marks on the bit were much lighter. I closed it slowly again - the plier tip scraped and it gouged significantly harder.
So there you go, it's probably better to just close it up quickly and not overthink it too much. That way the plier tip slips quickly over the bit doing less damage. I have a bit of mechanical sympathy though so I'll close it up in such a way that it won't scrape at all.
@chrono said:
Blade scrapping inside of the scales is a common problem inherent to the design itself. The liner lock has to be perfect within microns for the end tip of the blade to be perfectly centered.Looking closely at it I see what you mean. Knowing this I think I can live with it.
Thanks for your OCD post Aloha007.
The remaining concern then is the liner lock play in the serrated blade and the saw. I feel this is too sloppy for me to ever ignore so I'll return it and ask them to check the replacement Charge before they send it to me. The place I purchased it is in NSW too while I'm in Victoria. The quest for a nice solid Charge Plus continues.
-
@Mechanickal said:
My 07 TTI and 08 AL are absolutely PERFECT.Was I just lucky or was QC way better 10 years ago?
My Charge TTi from 2016 has no flaws, rubs, scrapes or misalignments. Knock on titanium...
-
My 07 TTI and 08 AL are absolutely PERFECT.
Was I just lucky or was QC way better 10 years ago?
My Charge TTi from 2016 has no flaws, rubs, scrapes or misalignments. Knock on titanium...
To be honest, the "issue" with the pliertip scraping the Phillips bit has to be "forced" for it to happen, like I explained a couple of posts back. If you're not closing the tool that specific way, and you're just closing it in a normal way at normal speed, you won't have this problem. So you really have to look for it. If I'm not doing it that specific way, I can also say non of my tools have this problem.
But doing it the other way, I can "produce" the "issue" on every Surge/Charge/Wave platform tool with a removable bit driver in it (so not on the Original Wave :P) that I own, and I own quite a few ...
Spoiler:
Wave second generation, Wave second generation BO, Wave +, Wave + BO, two 25th Anniversary Waves, Charge Tti old version scales, four Charge's AL, Surge and Surge BOI can even create the problem on the two Signals I own.
There's a difference between the pliertip scraping the bit and the side of the plierhead scraping against the inside of the handles. The first issue has to be produced, the second one you have to be lucky not to have it. I've got Waves/Surges/Charges which scrape a little bit (my edc Stainless Surge seems to want to destroy the finish on the side of the plierhead ::)) and I've got the same tool, same build year on which the side of the plierhead doesn't even come close to the inside of the handles... go figure ::)
-
I hope you get one that satisfies you. After shelving my TTi because the CC plier head in favor of my Wave I now realize how truly terrific it is. The CC is a non issue so far. I love the looks and really appreciate the S30V blade. I've don't have to fuss with it and have not for a good while. The tool lives on my work tool belt. Having the bits has saved me from making trips to get tools. I've made adjustments to so many different things over the years. Again I hope you get a proper tool that you can put to work.
-
All Leatherman tools are great prototypes. None is a finished design. I have a Charge TT, 2 Wingmans, one old PST II, a Surge and 2 Waves.
Because sometimes I went to USA and had to buy something. They are beautiful.
The Surge saw and file lock are the first model and it doesn´t lock. Then they added a lock to lock the lock and a hole in those blades HEHEHE.
The Wingman halves have a large play, but at least they stay closed. The Wingman file is very interesting: it serves to nothing, much less as a file.
But I love them all. They should buy a Victorinox Swiss Tool and learn from it.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
