Wave pocket clip on a Rebar (proof of concept)
-
Yup. I'd been thinking along these lines too, AW - unfortunately the handles are stainless steel, i.e. non-magnetic. TIG welding would probably work, but I lack the equipment (or the skills, for that matter).
Current thinking is to make a filler that carries that stop tab (itself pretty awkwardly formed) and keeps it abutted against the rolled handle edge, and epoxied into the handle just inside of the rolled edge where the handle is widest and where it won't interfere with the clip. I'm a little bit worried that handle twist may make that a futile exercise, though.
Just building up the stop tab from JB-Weld appears to me to be too weak to start with, it would wear out quickly even if it stayed put, which it might not for long given adverse loads on inserting or turning the clip...
-
With all this "add a bit here", and "add a bit there", would it not now (now you can see what needs to go where, and why) be easier to make a custom clip, using the Wave one as a template, but modifying the tang shape to suit the pivot and handle form? All that's needed is a bit of stainless, a vice, a hammer, and a dremel.
-

The origins of this project lie in the removability of the Wave clip and the almost identical positions of two of the three constraints (pivot and tool lock) between Wave and Rebar. The pivot only needed lengthening (Fuse) and the collar ring - check. The only thing that's still needed is the third constraint. That is proving to be a bit complicated
Fashioning a clip of my own would result in neither the versatility, nor nearly the neat finish, of the Wave clip. Can't take just any stainless, for instance, it needs to be springy enough. Then I shudder to think how it will look after I've deformed it :ahhh
I have some spring steel somewhere, I could check and see how rust-resistant that is and how it reacts to being maimed

-
Or use normal stainless and heat treat it after
you have finished shaping and finished making the clipThat way it will be springy

-
Or use normal stainless and heat treat it after
you have finished shaping and finished making the clipThat way it will be springy

... and discoloured
>:DYou will have to polish it up

-
I haven't given up on the Wave clip just yet... I'm thinking about fashioning (probably with some sharp files) a block of metal onto something with the profile shown below. Top right is where the clip's insertion leg comes on top, bottom left accepts the rounded-off handle edge, bottom further towards the right where the block would be epoxied to the handle...

-
Progress. JB Weld setting as I write this.




-
Hoping this works

-
is it holding with JB weld
Any problems with this or
does it work okay so far D_T
-
I've decided to let it set for the full advised 24h, which means no results until tomorrow morning at the earliest

-
Makes sense

-
Couldn't wait and tried the clip on/off at 23h 30m after applying the JB Weld. Seems to hold well and I'm happy to report that the wobble is now reduced to max about 1.5 mm at the end of the clip - roughly as much as on my SS ReWaveR. It helps that the filler plate abuts against the handle edge so shear on the bond caused by attempts to rotate the clip about the pivot axis is minimal. The only major strain is in compression, and the bond should be able to manage that. So tentatively I'm happy, but time will tell.
-
Nice one D_T hope it lasts

-
Latest pic:
/post/1796462
-
Glad that it worked out the way u wanted!

-
Looks really good

-
-
Thanks guys!

Almost looks as if LM wanted the Rebar to have a clip, doesn't it?

-
@Dutch_Tooler said:
Thanks guys!
Almost looks as if LM wanted the Rebar to have a clip, doesn't it?

all MTs should have the
option of using a pocket clip

Excellent work D_T

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login