The parts exchangeability thread
-
Nice mod (and info) Sam

"Work on the locking notch" of which nature? Well, I know, filing or sanding, but what are the differences in profile?
-
Some more reference info:
Hi, I'm very interested in modding my PST, but I have some concern about the tools fitting. Does someone with a digital caliper have the measurements of the thickness (of the area around the pivot hole) of the wave/charge saw, and of the surge saw/file holder. Thanks a ton!
reference Information
Diameter axes:
The diameter of the PST pliers axis - 4.8mm, length 9mm
Diameter pliers axis Wave Original - 4.8mm, length of 14.4 mm
Diameter pliers axis Wave New - 5.5mm, length of 13.3 mm
Diameter pliers axis Blast / Fuse / Kick - 5.5mm, length 16.4 / 14.8 / mm?
Diameter pliers axis ST300 - 5.5mm, the length of 9.5 mm
Diameter pliers axis Surge - 5.5mm, length 15.5mm
The diameter of the PST tool axis - 4.8mm
The diameter of the tool axis Wave Original -4.8 mm, length 13.1 mm
The diameter of the tool axis Wave - 4.8mm
The diameter of the tool axis Blast / Fuse / Kick - 4.8mm, length 16.4 / 14.8 / mm?
The diameter of the tool axis ST300 - 4.8mm
Shaft diameter with tools Surge- 4.8mm, Length 16.7mmThickness tools:
Phillips screwdriver Kick / Fuse / Blast - 5mm
Opener Kick / Fuse / Blast / Wave / Charge - 1,87mm
Knife Kick - 1,74mm
Ring Lanyard Kick / Fuse / Blast - 0,77 mm
All the other instruments (approximately) - 2,34-2,36mmTools SOG - 1,98mm (except adapter on bits)
-
Sam,
Good thread idea! Thank you.

Have you used any Flik tools(Saw and scissors) in an MP600? I have a beater Flik that was used as fodder for the plastic slide things and pliers replacement. Was thinking about just breaking it apart to customize another MP600/400.
-
@gerleatherberman said:
Sam,Good thread idea! Thank you.

Have you used any Flik tools(Saw and scissors) in an MP600? I have a beater Flik that was used as fodder for the plastic slide things and pliers replacement. Was thinking about just breaking it apart to customize another MP600/400.
It wouldn't work I think.. The pivot size on the flik's 4 main tools are larger than those on the mp400/600.
Not a simple drop in at least.. I have used a wave file with the 5.5mm sized pivot hole on a 600(smaller size) Locks up perfectly. Just have to be mindful of where you want to grind/file to have the maximum lock up.
but I doubt the flik have sufficient material for that. Have to check when I am back home. Happened to have a broken down flik also... 
My flik have a broken pliers tool.. It's a really complicated design at the bottom of the pliers. And weak ime.. It breaks/collapse on heavy pressure.. Actually the whole flik mechanism is really weird and overly complicated..
-
Thanks, Sam!

I'll leave the Flik alone for now. Maybe a messed up Flik with good pliers will show up one day.Yeah, the plier mechanism is ridiculous, to work on. Getting the 4 slide screws aligned through the plastic piece and two levels into the threads took 20 minutes when I did the swap.

-
@gerleatherberman said:
Thanks, Sam!
I'll leave the Flik alone for now. Maybe a messed up Flik with good pliers will show up one day.Yeah, the plier mechanism is ridiculous, to work on. Getting the 4 slide screws aligned through the plastic piece and two levels into the threads took 20 minutes when I did the swap.

;) here u go. It will not work...

-
I'll just add, that I put a LM Blast/Fuse Phillips, scissors and can opener on a SOG Powerlock with success
No grinding, sanding, cutting or modding needed, they fit just in and lock with minimal wobble

-
@Dutch_Tooler said:
Nice mod (and info) Sam
"Work on the locking notch" of which nature? Well, I know, filing or sanding, but what are the differences in profile?



The profile are very close. Just need to enlarge the notch a little. Go slow though. Any slight misalignment here and the tip of that tool will go off by a large angle. And that's super irritating. Its a one chance kind of thing.
-
@ThePeacent said:
I'll just add, that I put a LM Blast/Fuse Phillips, scissors and can opener on a SOG Powerlock with success
No grinding, sanding, cutting or modding needed, they fit just in and lock with minimal wobble

makes u think the 2 of them are buddies for a while.. :D -
This type of thread is a great idea for those of us tempted to try modding. However, I would prefer a separate thread for SAKS, mostly to avoid having to search past info that is irrelevant (and vice versa for pliers based tools).
Sent from my iPad using Tapatalk
-
@Sam Lim said:
Nice mod (and info) Sam

"Work on the locking notch" of which nature? Well, I know, filing or sanding, but what are the differences in profile?



The profile are very close. Just need to enlarge the notch a little. Go slow though. Any slight misalignment here and the tip of that tool will go off by a large angle. And that's super irritating. Its a one chance kind of thing.
OK, thanks

-
@Mizedog said:
This type of thread is a great idea for those of us tempted to try modding. However, I would prefer a separate thread for SAKS, mostly to avoid having to search past info that is irrelevant (and vice versa for pliers based tools).Sent from my iPad using Tapatalk
I appreciate the thought, however this would be counterproductive in case you were open to adding SAK tools into a plier based multitool and vice versa...
-
@Mizedog said:
This type of thread is a great idea for those of us tempted to try modding. However, I would prefer a separate thread for SAKS, mostly to avoid having to search past info that is irrelevant (and vice versa for pliers based tools).Sent from my iPad using Tapatalk
I think there's already a rather similar thread for the sak mods. Though I have never really done any mods for Sak, I am always amazed by what can happen in such a small little package. Its really a fine art as compared to a full fledge MT where alot of times its a die die make it fit kind of work. Sak mods are mostly very clean and detailed work. What I meant to say is that it is still a very informative and good read on the earlier part of this thread where there are alot of sak details even if I dun mess with them. But of course, you are free to start a new intended thread if u deem it to separate them.

-
O.k. this is absolutely tedious at best. I noticed from Sam's photo, the tool profiles are identical and I checked the Flik saw and noticed the bolt end of the pivot would be fine against the saw in the MP600. I needed to take up the gap so it would lock perfectly. I started with a hard steel lock washer. I cut a section out to fit around the Gerber mp600 tool pin. Used little vise-grips to hold the wadher in place while I ground 2/3 of its' mass off, rotating it in the grips a hit at a time. I made sure it was uniform all the way around. Then I pressed it into the Flik saw pivot and used a rotary file to smooth it out and make sure the 600 pin would move properly inside. Put a dab super glue to make sure it would never shift and voila, the Flik saw fit perfectly into the MP600 with no further modification.
I don't recommend this mod to the faint of heart. Here are some photos to show what I am rambling about. Photos 1-4.



-
Photos. 5-6.


-
That's a clever but shag way to make a bushing to fit! I have done equal stupid stuffs myself..
things we do to make things work. Another High Five!Many times I envy those that have access to CnC, Mills, welding equipments and such.. Like Diresta's setups. It's more difficult for us, but that's when we put on the thinking cap and start doing smurfy things to work around challenges.

-
Indeed. My last job had a mini lathe, among other machinist gear. Oh I miss that. I do feel the makeshift bushing I made will last as long as the tool, so I'm happy. But, you're right, some serious machinist tools would make it SOOOOO much easier. I spent 45 minutes getting the thing perfect. I think it could have been done on a lathe in a few minutes. I did bump my knuckle on the grinding wheel though(nothing bad).

We practice our mechanical creativity doing things the hard way.

Edit: oh yes. Forgot. Gives high five. :)
-
@gerleatherberman said:
O.k. this is absolutely tedious at best. I noticed from Sam's photo, the tool profiles are identical and I checked the Flik saw and noticed the bolt end of the pivot would be fine against the saw in the MP600. I needed to take up the gap so it would lock perfectly. I started with a hard steel lock washer. I cut a section out to fit around the Gerber mp600 tool pin. Used little vise-grips to hold the wadher in place while I ground 2/3 of its' mass off, rotating it in the grips a hit at a time. I made sure it was uniform all the way around. Then I pressed it into the Flik saw pivot and used a rotary file to smooth it out and make sure the 600 pin would move properly inside. Put a dab super glue to make sure it would never shift and voila, the Flik saw fit perfectly into the MP600 with no further modification.
I don't recommend this mod to the faint of heart. Here are some photos to show what I am rambling about. Photos 1-4.Small update. The arch of the saw back was sticking out of the 600 handle a tad bit(causing a new pinch area) and the lock didn't pull the saw in very well. Two areas needed addressing. 1) the back of the saw needed to be ground down 3mm-4mm and reprofiled to be more narrow. 2) the tang "bump" needed to be ground down 0.5mm or so to match the tang "bumps" of the other 600 tools. After the reshaping, the Flik saw is perfect in the MP600.
First photo shows the areas to be ground off colored black. Second photo is after the grinding and polishing were done. For anyone new to modding, the polishing of the tang "bump" ensures it doesn't damage the saf-t-lock plate. :)

-
That's a very nice and thick saw! It's funny how the companies comes out with new stuffs but people keep going back to the old goodies. ie. Mp400/600 series.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login