The parts exchangeability thread
-
@gerleatherberman said:
Thanks, Sam!
I'll leave the Flik alone for now. Maybe a messed up Flik with good pliers will show up one day.Yeah, the plier mechanism is ridiculous, to work on. Getting the 4 slide screws aligned through the plastic piece and two levels into the threads took 20 minutes when I did the swap.

;) here u go. It will not work...

-
I'll just add, that I put a LM Blast/Fuse Phillips, scissors and can opener on a SOG Powerlock with success
No grinding, sanding, cutting or modding needed, they fit just in and lock with minimal wobble

-
@Dutch_Tooler said:
Nice mod (and info) Sam
"Work on the locking notch" of which nature? Well, I know, filing or sanding, but what are the differences in profile?



The profile are very close. Just need to enlarge the notch a little. Go slow though. Any slight misalignment here and the tip of that tool will go off by a large angle. And that's super irritating. Its a one chance kind of thing.
-
@ThePeacent said:
I'll just add, that I put a LM Blast/Fuse Phillips, scissors and can opener on a SOG Powerlock with success
No grinding, sanding, cutting or modding needed, they fit just in and lock with minimal wobble

makes u think the 2 of them are buddies for a while.. :D -
This type of thread is a great idea for those of us tempted to try modding. However, I would prefer a separate thread for SAKS, mostly to avoid having to search past info that is irrelevant (and vice versa for pliers based tools).
Sent from my iPad using Tapatalk
-
@Sam Lim said:
Nice mod (and info) Sam

"Work on the locking notch" of which nature? Well, I know, filing or sanding, but what are the differences in profile?



The profile are very close. Just need to enlarge the notch a little. Go slow though. Any slight misalignment here and the tip of that tool will go off by a large angle. And that's super irritating. Its a one chance kind of thing.
OK, thanks

-
@Mizedog said:
This type of thread is a great idea for those of us tempted to try modding. However, I would prefer a separate thread for SAKS, mostly to avoid having to search past info that is irrelevant (and vice versa for pliers based tools).Sent from my iPad using Tapatalk
I appreciate the thought, however this would be counterproductive in case you were open to adding SAK tools into a plier based multitool and vice versa...
-
@Mizedog said:
This type of thread is a great idea for those of us tempted to try modding. However, I would prefer a separate thread for SAKS, mostly to avoid having to search past info that is irrelevant (and vice versa for pliers based tools).Sent from my iPad using Tapatalk
I think there's already a rather similar thread for the sak mods. Though I have never really done any mods for Sak, I am always amazed by what can happen in such a small little package. Its really a fine art as compared to a full fledge MT where alot of times its a die die make it fit kind of work. Sak mods are mostly very clean and detailed work. What I meant to say is that it is still a very informative and good read on the earlier part of this thread where there are alot of sak details even if I dun mess with them. But of course, you are free to start a new intended thread if u deem it to separate them.

-
O.k. this is absolutely tedious at best. I noticed from Sam's photo, the tool profiles are identical and I checked the Flik saw and noticed the bolt end of the pivot would be fine against the saw in the MP600. I needed to take up the gap so it would lock perfectly. I started with a hard steel lock washer. I cut a section out to fit around the Gerber mp600 tool pin. Used little vise-grips to hold the wadher in place while I ground 2/3 of its' mass off, rotating it in the grips a hit at a time. I made sure it was uniform all the way around. Then I pressed it into the Flik saw pivot and used a rotary file to smooth it out and make sure the 600 pin would move properly inside. Put a dab super glue to make sure it would never shift and voila, the Flik saw fit perfectly into the MP600 with no further modification.
I don't recommend this mod to the faint of heart. Here are some photos to show what I am rambling about. Photos 1-4.



-
Photos. 5-6.


-
That's a clever but shag way to make a bushing to fit! I have done equal stupid stuffs myself..
things we do to make things work. Another High Five!Many times I envy those that have access to CnC, Mills, welding equipments and such.. Like Diresta's setups. It's more difficult for us, but that's when we put on the thinking cap and start doing smurfy things to work around challenges.

-
Indeed. My last job had a mini lathe, among other machinist gear. Oh I miss that. I do feel the makeshift bushing I made will last as long as the tool, so I'm happy. But, you're right, some serious machinist tools would make it SOOOOO much easier. I spent 45 minutes getting the thing perfect. I think it could have been done on a lathe in a few minutes. I did bump my knuckle on the grinding wheel though(nothing bad).

We practice our mechanical creativity doing things the hard way.

Edit: oh yes. Forgot. Gives high five. :)
-
@gerleatherberman said:
O.k. this is absolutely tedious at best. I noticed from Sam's photo, the tool profiles are identical and I checked the Flik saw and noticed the bolt end of the pivot would be fine against the saw in the MP600. I needed to take up the gap so it would lock perfectly. I started with a hard steel lock washer. I cut a section out to fit around the Gerber mp600 tool pin. Used little vise-grips to hold the wadher in place while I ground 2/3 of its' mass off, rotating it in the grips a hit at a time. I made sure it was uniform all the way around. Then I pressed it into the Flik saw pivot and used a rotary file to smooth it out and make sure the 600 pin would move properly inside. Put a dab super glue to make sure it would never shift and voila, the Flik saw fit perfectly into the MP600 with no further modification.
I don't recommend this mod to the faint of heart. Here are some photos to show what I am rambling about. Photos 1-4.Small update. The arch of the saw back was sticking out of the 600 handle a tad bit(causing a new pinch area) and the lock didn't pull the saw in very well. Two areas needed addressing. 1) the back of the saw needed to be ground down 3mm-4mm and reprofiled to be more narrow. 2) the tang "bump" needed to be ground down 0.5mm or so to match the tang "bumps" of the other 600 tools. After the reshaping, the Flik saw is perfect in the MP600.
First photo shows the areas to be ground off colored black. Second photo is after the grinding and polishing were done. For anyone new to modding, the polishing of the tang "bump" ensures it doesn't damage the saf-t-lock plate. :)

-
That's a very nice and thick saw! It's funny how the companies comes out with new stuffs but people keep going back to the old goodies. ie. Mp400/600 series.

-
Indeed it is funny.

The MP is just the most reliable MT Gerber has ever built. Maybe the most reliable anyone has ever built.

The mod potential is crazy good and doesn't require machining tools. So that is a big reason too.One last use of that poor Flik. I have always been agitated that Gerber only has a #2 phillips on the 400/600. Well, with some minor grinding, I have swapped the lanyard for the #1 Phillips on the Flik. This 600 now has FIVE screw drivers. Sm. Flat, Med. Flat, Lg. Flat, #2 Phillips, and #1 Phillips. Wood Saw, double-sided file, plain blade, and serrated blade. I will eventually replace the plain blade with scissors (when I can find some, as the flik scissors would require me to make two more bushings and grind a thumb pad opening in the 600 handle (I want to retain original look/feel of this particular tool). I may grind the Flik can opener into a reamer/awl at somw point too.
The Flik Small tools(the pivots are small inside and larger outside the frame) have an identical pivot hole as the 600. Only modding was to remove the tang bump closest to the driver head.This tool is being readied to replace my 'non-carbide head' BN600 soon, as the old one is just kind of worn out. If I can find a non-carbide-cutter BN plier head, that will be swapped too.




-
always good to see more philips in a MT. Btw do u need to make a bushing also or the pivot happen to be the same? I have not tore down the flik's internals yet. -
More OG goodness.
Supertool's main blade in a Wave. Good amount of tang material to play around with. I like the blade shape. No more oho. Does this makes it legal for some places' weird-ish knife laws?





-
@Sam Lim said:
always good to see more philips in a MT. Btw do u need to make a bushing also or the pivot happen to be the same? I have not tore down the flik's internals yet.The four little tools in the flik have identical pivot hole sizes to MP tools. The inner tools pivot on a captive nut(that the outside tool pivot screws are mounted with) the size of the MP pivot. If you hav any issues removing the inner tool "cluster", let me know. There is a small chrome "retention" clip that has to be removed to take the black platic thing out if the handle. After that, the cluster drops out and you can push out the captive bolt out of the cluster to remove the tools. You also get some more "anti-clump" washers that fit the MPs. :)
@Sam Lim said:
More OG goodness.Supertool's main blade in a Wave. Good amount of tang material to play around with. I like the blade shape. No more oho. Does this makes it legal for some places' weird-ish knife laws?

Good job. The ST blade is a winner of a blade.

-
@Sam Lim said:
More OG goodness.Supertool's main blade in a Wave. Good amount of tang material to play around with. I like the blade shape. No more oho. Does this makes it legal for some places' weird-ish knife laws?

That would make it street legal in Germany, for instance (provided you did the same to the serrated blade if present).
Nicely done!
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login