Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Peening Question

Scheduled Pinned Locked Moved The Mod Squad
3 Posts 1 Posters 1.6k Views
  1. Home
  2. Tool Talk
  3. The Mod Squad
  4. Peening Question
Peening Question
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • Ben X Offline
    Ben X
    Posts: 276
    Ben X Offline
    Ben X
    wrote on last edited by
    Quote Reply

      Alright so I was attempting to follow Neil's corkscrew/phillips swap guide and turn a tourist into a small tinker. I filed the pin down almost flush with the scale and chased it with my punch. Now, there are a couple of things I can imagine to be factoring into things not going as I had hoped. First of all is that instead of 2.25mm brass I am using .081in- the equivalent of 2.0574mm. Also as I tapped the brass rod through and it fought a little- I am concerned it might do allowing the liner and hole to swell out- if that makes sense- or stretch down into the gap, creating a problem when peening it back together.
      So the first time I got it together, it wasn't too tight, it just didn't have the snap I thought it would. So, considering the brass rod size difference, it might just not be putting as much tension on the backspring, although the peening job is fine. The second time I peened it but didn't have the brass short enough, so it had blade play, and also little snap. Then the third time I overpeened, and my silly roommate is studying so I don't want to keep hammering the night away and piss him off.
      So, my question is which would contribute to the reduced snap- overpeening, the caved in liner (slightly) or the undersized brass rod? I did use this size rod successfully with my last mod so that's perhaps what baffles me most. Likewise, when it was underpeened, there was still no snap. Finally, I even tried to "repair" the line area with filing, hammering to flatten out (with blade tangs in place as a guide) and all to no avail. Help? :-\ :surrender: :surrender: :think:

      1 Reply Last reply
      • Gareth Offline
        Gareth
        Admin Team
        Posts: 37,725
        Gareth Offline
        Gareth
        Admin Team
        wrote on last edited by
        #1 Quote Reply

          Most likely it's a combination of the slimmer brass rod and the slight damage to the hole. Add those together and it sounds like, as you say, the tool isn't being held tightly enough to the backspring. How is the action on the blades?

          1 Reply Last reply
          • scibeer Offline
            scibeer
            Posts: 427
            scibeer Offline
            scibeer
            wrote on last edited by
            #2 Quote Reply

              Yep. All those things will effect snap. The right size keeps the snap closest to factory and I have tried them all. Anything under about .085in for the center pins will give you a little less.

              Once the liner is bent its tough to get it fixed without taking the knife apart, flattening it out and sanding it smooth.

              1 Reply Last reply

              Hello! It looks like you're interested in this conversation, but you don't have an account yet.

              Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

              With your input, this post could be even better 💗

              Register Login

              1. Home
              2. Tool Talk
              3. The Mod Squad
              4. Peening Question
              Reply
              • Reply as topic
              Log in to reply
              COMMUNITY LINKS
              EDC-TV SAKWiki GearFeed SAKSelector
              Operational Funds

              Help us keep the Unworkable working!

              Make A Donation
              November Goal: $300.00
              Due Date: Nov 30
              Total Receipts: $0.00
              Below Goal: $300.00
              0% funded
              • Login

              • Don't have an account? Register

              • Login or register to search.
              • First post
                Last post
              0