The Great Multi-Tool Restoration Thread!!!
-
Great job Dave another top notch clean up

You are getting very good at that
:D -
@MultiMat said:
Nice job again Dave, I really like my A100. Did you remove the main blade Dave & have to tackle that tiny nut
The main blade is dead easy to remove. The little nut that you refer to is actually welded in place, so you only need to remove the external one (for which I used the socket you can just see in one of the pics).
Before I realised that, I was intending to grip the internal nut with a Squirt P4 or Clutch - didn't need to in the end though.
-
Nice job again Dave, I really like my A100. Did you remove the main blade Dave & have to tackle that tiny nut

The main blade is dead easy to remove. The little nut that you refer to is actually welded in place, so you only need to remove the external one (for which I used the socket you can just see in one of the pics).
Before I realised that, I was intending to grip the internal nut with a Squirt P4 or Clutch - didn't need to in the end though.
No weld I my one ya lucky dog , I tried the Squirt & Crunch & not enough room :ahhh
-
Nice job again Dave, I really like my A100. Did you remove the main blade Dave & have to tackle that tiny nut

The main blade is dead easy to remove. The little nut that you refer to is actually welded in place, so you only need to remove the external one (for which I used the socket you can just see in one of the pics).
Before I realised that, I was intending to grip the internal nut with a Squirt P4 or Clutch - didn't need to in the end though.
No weld I my one ya lucky dog , I tried the Squirt & Crunch & not enough room :ahhh
Are we talking about the same thing?

-
Fu#k me Dave & your BIG red arrow (you should have been a teacher) . You just made me leave my cider & corn chips to go too my treasure chest. Yes the P4 can sort of grip the nut if you tilt your head, bite your lip & say a prayer. But not well enough too hold in place.
BTW I think your A100 not only has a bloody weld but clearly it is bigger than my nut
:D :D :D :D :D.
I could of said your A100 has got BIGGER NUTS but that would be un- Australian :P :D :D :D -
Did you like the way I used a pink Squirt, 'cos you're being a big girl about it ;)
:D
Get into it. You can't make an omelette without breaking eggs, etc

-
In case Ben reads this:

-
So Dave what is the best thing for cleaning bird poo out of multitools ?? Or should I ask Ben :D :D :D
-
Definitely Ben's area of expertise that one.
-
Well Dave, you've inspired me to get after an old A100 I've got. Actually it is one with Craftsman markings, but exactly the same as the Kershaw in all other respects. Nothing horribly damaged on it, just plenty of dings and scratches and gunk.
Here is a picture of it gutted. With any luck I'll have it reassembled this evening.

-
@J-sews said:
Well Dave, you've inspired me to get after an old A100 I've got. Actually it is one with Craftsman markings, but exactly the same as the Kershaw in all other respects. Nothing horribly damaged on it, just plenty of dings and scratches and gunk.Here is a picture of it gutted. With any luck I'll have it reassembled this evening.

I take it your not drinking tonight then :D Imagine what it would be like if I put it back together :o
Dunc
-
Bob. The black "block" on the left of the picture - about half way up - is that the thread that the adjusting screw fits into? If so, is it plastic on yours? Mine is metal - probably aluminium.
-
@DaveK said:
Bob. The black "block" on the left of the picture - about half way up - is that the thread that the adjusting screw fits into? If so, is it plastic on yours? Mine is metal - probably aluminium.That is indeed the adjusting screw block. Mine is steel. It is discolored though, as if it has been heat treated?
I'd take a close up picture but it is already reattached. :-\
-
Done. 8) (bottom one in the pictures)


The screwdrivers were all boogered up. I reshaped them with a diamond file. Touched up the knife blade and re-buffed it with the dremel. Also used a little wire wheel attachment on the dremel to remove all the rust speckles. It worked surprisingly well. On tools with a bead blast finish (the A100, many Gerber tools, Leatherman SideClip, etc) the rust speckles get started rather easily. Removing them with steel wool or scotch brite leaves a spot that never matches the factory finish. The little dremel wire wheel is the answer to that problem. :)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

