PowerPint Overview Mighty Little MT
-
Excellent improvement, Sakpan!

-
@Sakpan74Gr said:
Considering that the file is nothing to write home about, I thought it would be useful to shape the end as a scrapper. (Is that what it is? English isn't my first language...) You can see before and after the Dremel treatment.


Στάλθηκε από το HUAWEI VNS-L31 μου χρησιμοποιώντας Tapatalk
Pretty nice!
Great idea, maybe I'll try that too. -
It has been a while since the Pint came out. My thoughts are mostly positive.
Pros:
Compound leverage on the mid-sized plier head.
Outside tool access.
Locking tools.
Pocketable.
Stronger than expected.
After the tool went through a 'break-in' period, the tools and pliers deploy, lock and unlock smoothly and a slight snap holdin the tools in now (not perfect, but acceptable).
Easy to disassemble.
After a while, the scissors got a bit easier to use. Not great, but mediocre.Cons:
My first one had a screw head break off when using the phillips driver hard. SOG took care of it. While SOG had it, I bought another one. It has had no problems so far.
Scissors are uncomfortable on harder materials.
File is mediocre at best.
Cutter hook came dull and the design isn't effective
You have to slightly open the handles to unlock the toolsI may be forgetting something, but those are my thoughts so far.
-
@Exeter said:
And I almost forgot: I mentioned I didn't really like the stowash finish, so I polished the middle "panel" on the handles. It came out pretty nice, at least for my eyes. It's not easy to show on camera, but irl it looks quite stylish like this.This is really beautiful! How did you do it? Sandpaper? What kind of grit?
Στάλθηκε από το HUAWEI VNS-L31 μου χρησιμοποιώντας Tapatalk
-
And I almost forgot: I mentioned I didn't really like the stowash finish, so I polished the middle "panel" on the handles. It came out pretty nice, at least for my eyes. It's not easy to show on camera, but irl it looks quite stylish like this.
This is really beautiful! How did you do it? Sandpaper? What kind of grit?
Στάλθηκε από το HUAWEI VNS-L31 μου χρησιμοποιώντας Tapatalk
I used 1000 and 2000 grit sandpaper if I remember correctly and then green polishing compound.
-
REPLACE THE SCISSORS AND FILER TO MAKE IT PERFECT
On paper, the Powerpint appears to be the perfect edc for me since it ticks all the boxes for me.... pocketability, all-outside tools deployment, comprehensive tool selection, etc.. However, based on the reviews I have seen so far, I am very concerned with the scissors and filer which I use often.
I am thinking, if I do get the Powerpint, whether I could replace the scissors and filer with one from say, a Victorinox Classic (or some other MT). What do you guys think? Do you think it would work? Any advice would be greatly appreciated ! Thanks in advance.
-
Welcome to the forum roamingcat and enjoy your time here!
I'm not sure about the modding possibilities in that sense, but I'd be curious to see what others might come up with.
And yeah, the scissors are just plain bad, I had the springbar just snap on me last week while cutting paper! I wrote to SOG asking about warranty, and if they could send me a replacement spring part, but they informed me that I'd have to send the whole tool in for repair. Financially it just wouldn't make sense for me, shipping would be 70% of the original price I paid for it, so now I'm stuck with non-functional scissors. ...any modders, handy MTO-ers wanting to try their hand at making a replacement spring? ;)

-
@Exeter said:
Welcome to the forum roamingcat and enjoy your time here!I'm not sure about the modding possibilities in that sense, but I'd be curious to see what others might come up with.
And yeah, the scissors are just plain bad, I had the springbar just snap on me last week while cutting paper! I wrote to SOG asking about warranty, and if they could send me a replacement spring part, but they informed me that I'd have to send the whole tool in for repair. Financially it just wouldn't make sense for me, shipping would be 70% of the original price I paid for it, so now I'm stuck with non-functional scissors. ...any modders, handy MTO-ers wanting to try their hand at making a replacement spring? ;)
I wouldnt bother with making a spring for the scissors though. The scissors is just plain bad. Giving it the best spring in the world doesn't make any difference. I broke it the first day of acquiring it. What roamingcat said is in the right direction. It needs to be replaced. I somewhat have a wave scissors in there on the very first day. Needs lots of refinement but works miles better than the original scissors.
-
@Exeter said:
Welcome to the forum roamingcat and enjoy your time here!I'm not sure about the modding possibilities in that sense, but I'd be curious to see what others might come up with.
And yeah, the scissors are just plain bad, I had the springbar just snap on me last week while cutting paper! I wrote to SOG asking about warranty, and if they could send me a replacement spring part, but they informed me that I'd have to send the whole tool in for repair. Financially it just wouldn't make sense for me, shipping would be 70% of the original price I paid for it, so now I'm stuck with non-functional scissors. ...any modders, handy MTO-ers wanting to try their hand at making a replacement spring? ;)
Thank you Exeter for your kind words. Sorry to hear about your scissors :(. Seems like it is a fairly common problem and hopefully our community here can collectively work out a solution.
I am interested to hear more about Sam's solution, i.e. replacing it with a Wave scissors. Sam, if it is not too much trouble can you post some pics and tell us a little bit more how you did it? I have a Leatherman Fuse which I don't use often and I am happy to 'transplant' the scissors to the PowerPint if I could. I really like to get the PowerPint as its design & configuration fits my requirements perfectly. Thanks so much.
-
Welcome to the forum roamingcat and enjoy your time here!
I'm not sure about the modding possibilities in that sense, but I'd be curious to see what others might come up with.
And yeah, the scissors are just plain bad, I had the springbar just snap on me last week while cutting paper! I wrote to SOG asking about warranty, and if they could send me a replacement spring part, but they informed me that I'd have to send the whole tool in for repair. Financially it just wouldn't make sense for me, shipping would be 70% of the original price I paid for it, so now I'm stuck with non-functional scissors. ...any modders, handy MTO-ers wanting to try their hand at making a replacement spring? ;)
Thank you Exeter for your kind words. Sorry to hear about your scissors :(. Seems like it is a fairly common problem and hopefully our community here can collectively work out a solution.
I am interested to hear more about Sam's solution, i.e. replacing it with a Wave scissors. Sam, if it is not too much trouble can you post some pics and tell us a little bit more how you did it? I have a Leatherman Fuse which I don't use often and I am happy to 'transplant' the scissors to the PowerPint if I could. I really like to get the PowerPint as its design & configuration fits my requirements perfectly. Thanks so much.
Hi! The pic of the wave scissors are just a few post up. Works but not the best solution.. Yesterday night after reading this post, I have again made some, I would say proper improvement. Let me get back home later to post up my solutions.

-
Here you go! I would say ditch that scissor and put in something else. Mine came from a crappy guidesman multitool. The scissors cuts very well though. Shouldnt be too difficult to find something that fits. But I am afraid a Vic SD will not work as theres not enough material around the pivot tag. Its was polished like a Vic's but I gave it a quick acid bath to match the finish. Not entirely a drop in, just some filing here and there.
Theres another thing that needs work on though. The handles are floppy as smurf, making the pocket clip absolutely useless as the handles will open in the pocket.. Gotta find a way to keep them closed..



Donor MT

-
[/quote
Hi! The pic of the wave scissors are just a few post up. Works but not the best solution.. Yesterday night after reading this post, I have again made some, I would say proper improvement. Let me get back home later to post up my solutions.
[/quote]Thanks Sam. This sounds promising. Looking forward to your 'scissors solution'. Sorry for missing your earlier pics on the Wave scissors .... its reasuring to see the PowePint has good modding potential ! I really like the PP but I need it to have a pair of scissors that last for more than a week !
(sorry - cross post I think we posted simultaneously ... thanks for the update Sam !)
-
@roamingcat said:
[/quote
Hi! The pic of the wave scissors are just a few post up. Works but not the best solution.. Yesterday night after reading this post, I have again made some, I would say proper improvement. Let me get back home later to post up my solutions.
Thanks Sam. This sounds promising. Looking forward to your 'scissors solution'. Sorry for missing your earlier pics on the Wave scissors .... its reasuring to see the PowePint has good modding potential ! I really like the PP but I need it to have a pair of scissors that last for more than a week !
(sorry - cross post I think we posted simultaneously ... thanks for the update Sam !)
[/quote]
modding potential I can't say much.. The pivot size is not quite a regular one.. I dun have a caliper to measure that. But at least its held together by screws and not rivets! -
Nice work Sam. Thanks for posting !
-
Got my hand on a PowerPint in a lot deal. I have not used it yet, just played with it. My first impression is, this tool has a lot of potential, and can be a homerun for SOG. Immediately, the LM Juice series came to my mind as its competitor. Improvements can be done to this little gem IMO:
- Move the pocket clip to the pliers's pivot end
- Redesign the handles' cutouts for true one-hand opening
- The implements are quite crude. They need to be more polished
- Fix the file profile and the scissors' tension
I like the fact that I can adjust the tightness at the pivots. And there is no painted aluminum scale to worry about.
-
Congrats on getting your Pint, Chrono!

SOG has some almost-fantastic tools right now But, for some unbeknownst reason, chooses to stay the course with the way they are already.

You have good points listed there, Chrono.

-
@chrono said:
Got my hand on a PowerPint in a lot deal. I have not used it yet, just played with it. My first impression is, this tool has a lot of potential, and can be a homerun for SOG. Immediately, the LM Juice series came to my mind as its competitor. Improvements can be done to this little gem IMO:- Move the pocket clip to the pliers's pivot end
- Redesign the handles' cutouts for true one-hand opening
- The implements are quite crude. They need to be more polished
- Fix the file profile and the scissors' tension
I like the fact that I can adjust the tightness at the pivots. And there is no painted aluminum scale to worry about.
Just got mine too.
entirely. Imo the PP is a great design
but flawed badly in its implementation
. The materials used and construction feels flimsy compared to the Leatherman Juice which I think is its closest substitute. The scissors and filer in particular needs improvement, badly. I think I will limit the PP scissors to cutting excess garment threads only to avoid breaking it.I really hope SOG will release a PP version 2 with the same basic design but improve upon the points mentioned above ... just look at how Leatherman / Vic do their scissors and filer, and upgrade the material to proper stainless steel (instead of the not-too-sure cheap alloy used currently?)
I attach a comparison shot of the similarity (size-wise) between PP and Juice S2 (currently being modded slightly pending my new pivots to arrive).


-
I agree with your points, except the steel being inferior. I do agree that PP looks like the steel is "cheap", but fortunately, that is a perception side effect from the stonewash finish. The steel is actually the same mid-grade stainless found in their other tool's frames. The steel is similar to most other companies frame/handle steel. The poor machining of the file is a strong disappointment for sure. The scissors are not well designed, but would be drastically better with just a softer wire spring like Gerber uses. That piece of metal that acts as a spring is prone to breaking under use, because it was probably never intended to be tempered into spring steel(one of the reasons it takes a few pounds of pressure to move it).
-
Thanks for clarifying and reassuring the steel material used. I wonder if anyone has figured out how to replace the springs for the scissors as it has been reported it has broken by a few posters before? I really want to use the scissors more than just cutting off excess garment threads.

-
@roamingcat said:
Thanks for clarifying and reassuring the steel material used. I wonder if anyone has figured out how to replace the springs for the scissors as it has been reported it has broken by a few posters before? I really want to use the scissors more than just cutting off excess garment threads.

As you know, Sam Lim has swapped in a pair of cheapie scissors, but that is a good question. I have not seen any posts about changing the scissor spring. I may be taking one of my Pints apart at some point and will try and remember to look at spring alternatives. :)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login