Appreciating the boxcutter/utility knife
-
As with most types of edged tools,the lowly box cutter has also come into my accumulation in many designs.Some are designed for multiple uses such as scraping. It wasn't until many years after I started using a standard box cutter did I realize that in most of them you can take out the blade and turn it 90 degrees to use as a scraper.
The only down side I see to replaceable blade utility knives is that most of them use blades that will only fit that particular knife.Many of the early ones used single edge razor blades of the standard type. There were also many types of single edge razor blades when safety razors started to replace straight razors but that is another story......
So without further ado I will post up a few of mine and try to give info about them.#1 Armstrong Notched Blade Knife.Cast iron housing.Still looking for extra blades.
#2 Box cutter promotional item from Swift's Cleansers.Uses a single edge razor blade.
#3 Conrad box cutter uses a single edge razor blade.Has a ruler built in to the top edge.
#4 A modern Craftsman folding utility knife with wood handles and highly polished with removeable blade guard.
#3

-
Page two:
#1 A pair of Crescent utility knives.Top one slides in either direction and has two different blades.
#2 Not sure what this one is used for with the replaceable small blade.Marked Dan C. Laub Minneapolis Minnesota
#3 Garvey Fast-Cut uses specialized blades.
#4 A group of utility knives/cigar cutters.The RazCut Ripper uses a standard single edge blade.The Gillette models use their special Valet blade.The bottom one is a sliding blade.



-
Those all look so cool, Ray 8) I especially
the Gilette ones though

-
Page three:
#1 A left handed box cutter!
#2 & 3 A Hyde scraper/cutter open and closed.
#4 A modern Husky pocket/utility knife. -
Page four:
#1 Kutto utility knife.
#2 Lewis utility knife with a spring loaded fold down guard.
#3 Old cast iron model stamped Made in USA. Looks like a Stanley.
#4 A group of small size utility knives. -
Page five:
#1 An unusual one marked only Pat. Apl'd. Body is cast iron and holds the blade inside. To use;slide the case open and insert blade into slot;close cover locks blade in position. -
Page six:
#1Quick-Blade folding knife.Notch on bottom of blade is for cutting tape.
#2 Red Devil Jak Nife Can be used as a knife or a scraper and folds up for safety.
#3 A couple of early cast iron Stanley knives(model 1299)
#4 A Uni-Tool multiblade knife.


-
Last ones for now:
#1 A group of Gillette utility knives with extra blades.
#2 A group of small utility knives.
#3 A pair of Stanley 10-049 folding utility knives.The blade release is effected by sliding the plastic tab on the back to the rear.
#4 A Stanley 10-059 funny folder knife.



-
Cool collection

-
:D

-
Always had a thing for the Olfa cutters too!
Back when I installed Tint and Security Film these were all we used.
Sent from my iPhone,dont expect too much[emoji85]
-
@CallsignBadger said:
Thats lame >:(Good thing you got it changed
I also have the blue one on the bottom of the second pic. Mine is branded Sheffield


My blue one is also a Sheffield.

-
@Ray S said:
As with most types of edged tools,the lowly box cutter has also come into my accumulation in many designs.Some are designed for multiple uses such as scraping. It wasn't until many years after I started using a standard box cutter did I realize that in most of them you can take out the blade and turn it 90 degrees to use as a scraper.
The only down side I see to replaceable blade utility knives is that most of them use blades that will only fit that particular knife.Many of the early ones used single edge razor blades of the standard type. There were also many types of single edge razor blades when safety razors started to replace straight razors but that is another story......
So without further ado I will post up a few of mine and try to give info about them.#1 Armstrong Notched Blade Knife.Cast iron housing.Still looking for extra blades.
#2 Box cutter promotional item from Swift's Cleansers.Uses a single edge razor blade.
#3 Conrad box cutter uses a single edge razor blade.Has a ruler built in to the top edge.
#4 A modern Craftsman folding utility knife with wood handles and highly polished with removeable blade guard.
#3Ray, I was a flooring installer for 33 years. The Armstrong knife you have has been replaced by a plastic angled model. At one time they made an angled straight blade for it that ship has sailed. If I remember right the notched blades for the new knife fit yours. When pattern cutting sheet vinyl flooring you cut halfway through the flooring and undercut the backing with a notched knife like yours. Mostly used with inlayed hard goods but can be used with any vinyl flooring. Most wholesale flooring supplys should stock Armstrong blades.
-
@Mike 56 said:
Ray, I was a flooring installer for 33 years. The Armstrong knife you have has been replaced by a plastic angled model. At one time they made an angled straight blade for it that ship has sailed. If I remember right the notched blades for the new knife fit yours. When pattern cutting sheet vinyl flooring you cut halfway through the flooring and undercut the backing with a notched knife like yours. Mostly used with inlayed hard goods but can be used with any vinyl flooring. Most wholesale flooring supplys should stock Armstrong blades.Mike:Thanks for the info on the Armstrong. I'll have to check to see if I can find any locally.
-
I've got a Gerber EAB which I never use....just had my name on it :P
I use the old standard Stanley model, one fixed and one with the retractable blade. The latter is a pain, I always seem to disengage the lock during hard use.....
Something else.......if you have a polisher you can strop the blades back to sharper than new in a few seconds.
-
Ray, I found some Armstrong blades in my linoleum box. If you live in the states PM me your address and I will send you a few.
-
Only a few here.
Cheapo plastic Stanley (model not known). Good for light work and quick blade changes.
Stanley 99E. Will easily outlive me. Good solid beast of a knife. Slow on blade changes though.
Forge steel auto-retract (pain in the arse to use for anything other than single cuts). No additional tools needed to open it, which is good. Solid enough to survive being thrown across the room, if you lose your rag over the auto-retract feature. Launch durability tested many times.
And then both the EAB and EAB Lite. Sadly the concave and convex blades need modding slightly to fit. Not a long job though, if you've got some kind of powered grinder.

-
I bought a Gerber folding utility knife from Amazon just got it today feels real good in my hand. Walmart sell them with orange handles for under eight dollars when you can find them in stock.


Sent from my iPhone using Tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
