spartan lite upgrade.
-
I am a fan of the spartan. But i find that typicaly my edc is either a climber, explorer, or pioneer x. However depending on what im doing that day sometimes i need a flashlight so the spartan lite fills a needed gap.
-
Sorry to drag up an old thread but do you know the model of led you used please? The leds I've found for doing this run at about 3.6v but the spartan lite uses 2x 3v batteries = 6v.
Or is there something I'm missing? ???Thanks
-
Gotta find a beater "lite" model (preferably a Huntsman Lite) and try this. I have a Master Gardener, which being an older model has the old dim LED. Even dimmer than my ca. 2012 Wenger Microlight Esquire. But it's too uncommon to mess with.
-
The leds have a voltage bias typicaly between 2.9-3.6v. The will still work fine with a 3v battery. The batteries are in parallel not in series like most flashlights. Eg. Two batteries will still provide only 3v.
-
@armi101 said:
The leds have a voltage bias typicaly between 2.9-3.6v. The will still work fine with a 3v battery. The batteries are in parallel not in series like most flashlights. Eg. Two batteries will still provide only 3v.Ahh I see

Just waiting for my spartan lite to arrive then I can begin tinkering >:D
Is the original led round topped or flat top?
I've managed to find and 18000mcd cool white leds so thinking I might try one of them. -
@armi101 said:
The leds have a voltage bias typicaly between 2.9-3.6v. The will still work fine with a 3v battery. The batteries are in parallel not in series like most flashlights. Eg. Two batteries will still provide only 3v.That doesn't sound right...pretty sure they are in series.
I'll have to try the mod regardless. It seems like there are different levels of brightness even with the original Lites. I think they're generally much brighter starting in '12 when the housing was changed. The newest clear ones are all brighter. I've noticed the same in the 58mm scale lights.
@craggus2000 said:
Ahh I see
Just waiting for my spartan lite to arrive then I can begin tinkering >:D
Is the original led round topped or flat top?
I've managed to find and 18000mcd cool white leds so thinking I might try one of them.They all look round to me. In both the 91mm and 58mm knives.
-
Opened the battery door. They are in series. My mistake.
-
Are there any other components in there, eg resistors? Or is it just 2 batteries, a switch and an led?
-
@craggus2000 said:
Are there any other components in there, eg resistors? Or is it just 2 batteries, a switch and an led?Just the batteries/switch/led and simple conductors.

-
@gerleatherberman said:
Just the batteries/switch/led and simple conductors.
I wonder if it needs a resistor in that case? Surely 6V to a 2.9-3.6V LED wouldn't do it much good without one?
Or try and re-wire the batteries to parallel? Maybe easier said than done though

-
I would just make a dummy battery(to put in the place of the battery not contacted by the switch) to reduce the voltage to 3V.
If you wanted to be creative, you could move the contacts to bypass the secondary batter place(the one the switch doesn't contact to). That way you have a backup battery on board.
All that said, why not just carry a real flashlight and have the dim Lite as an emergency backup?
-
@gerleatherberman said:
If you wanted to be creative, you could move the contacts to bypass the secondary batter place(the one the switch doesn't contact to). That way you have a backup battery on board.I like that idea!

@gerleatherberman said:
All that said, why not just carry a real flashlight and have the dim Lite as an emergency backup?Because that's the easy option :D

-
Fair enough.

The Spartan Lite is one of the SAKs I've carried off and on before. Great toolset for simple electrical/electronic related work. :)
And yes, I did use the Lite feature many times when I misplaced my dedicated light.. :) -
1 battery mod is easy enough. Just bend the negative contact from the LED to touch the door contact. I have one that's bypassed like that for extra dim light.
Bend it over the battery (or side) if you want to keep one as spare.
-
@kamakiri said:
1 battery mod is easy enough. Just bend the negative contact from the LED to touch the door contact. I have one that's bypassed like that for extra dim light.Bend it over the battery (or side) if you want to keep one as spare.
Could you post a pic, as I'm trying to figure out the best way to bend it?
Thanks -
Look like I modded it again after to use the other cell, but moved the switch side positive contact instead (outside of the red switch 'channel':

This way it works with 1 battery in either location. A spare can be carried, but MUST face the same direction (+ side up) or it will short when the switch is turned on.

Bend the negative tip up to touch the door contact. Make it go over the battery IF you want to store a spare batt there. I did not do that, just bent the neg contact up to touch the lid contact and could only use the outer battery location like that.
If you don't want to make it permanent, just stick a small ball of foil in there to make the contact. Just means you can't carry a spare.

Both lites are ON:

Light from my monitor about 2' away overpowers the light about 1' away from the wall.
-
Glad it worked. Such a simple mod and it makes the tool soo much more usable. I feel like the light is very overlooked.
I put one in an explorer instead of the mag. It might be my favorite toolset.
-
It is pretty common to run "3V" LEDs on 2 x 3V button cells in series, look at any "Fauxton" as an example. When in use not many 3V button cells will supply a full 3V for very long, and over-driving the LED does give a lot more light.
Most reasonable quality LEDS will survive being over-driven for short(ish) periods. They might not last the usual 40-50,000 hours, but that isn't a serious problem for most people.
If you want an LED that will work OK on one 3V battery look at yellow or red LEDs, these seem to work better on lower voltages than white LEDs.
-
@armi101 said:
Glad it worked. Such a simple mod and it makes the tool soo much more usable. I feel like the light is very overlooked.I put one in an explorer instead of the mag. It might be my favorite toolset.
I haven't modded the LED just yet! I gotta order some for future builds...
And I agree with you on the Lite modules...I'd like to put one in almost every mod. I have lots of Spartan Lites for donors. One with the new clear case, a few with the newer '12+ gray case and several with the original '04 type.
-
I don't know why I didn't think of this before, but to use one battery you don't need to change anything apart from have both batteries facing positive upwards! No wire bending required.

The conductor on the door effectively uses the metal of the second battery as a conductor so only the battery nearest the led is actually used. The one furthest away isn't used as the negative is not connected to anything so that's the spare one.
Bingo, 3v instead of 6v.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login