spartan lite upgrade.
-
@craggus2000 said:
Are there any other components in there, eg resistors? Or is it just 2 batteries, a switch and an led?Just the batteries/switch/led and simple conductors.

-
@gerleatherberman said:
Just the batteries/switch/led and simple conductors.
I wonder if it needs a resistor in that case? Surely 6V to a 2.9-3.6V LED wouldn't do it much good without one?
Or try and re-wire the batteries to parallel? Maybe easier said than done though

-
I would just make a dummy battery(to put in the place of the battery not contacted by the switch) to reduce the voltage to 3V.
If you wanted to be creative, you could move the contacts to bypass the secondary batter place(the one the switch doesn't contact to). That way you have a backup battery on board.
All that said, why not just carry a real flashlight and have the dim Lite as an emergency backup?
-
@gerleatherberman said:
If you wanted to be creative, you could move the contacts to bypass the secondary batter place(the one the switch doesn't contact to). That way you have a backup battery on board.I like that idea!

@gerleatherberman said:
All that said, why not just carry a real flashlight and have the dim Lite as an emergency backup?Because that's the easy option :D

-
Fair enough.

The Spartan Lite is one of the SAKs I've carried off and on before. Great toolset for simple electrical/electronic related work. :)
And yes, I did use the Lite feature many times when I misplaced my dedicated light.. :) -
1 battery mod is easy enough. Just bend the negative contact from the LED to touch the door contact. I have one that's bypassed like that for extra dim light.
Bend it over the battery (or side) if you want to keep one as spare.
-
@kamakiri said:
1 battery mod is easy enough. Just bend the negative contact from the LED to touch the door contact. I have one that's bypassed like that for extra dim light.Bend it over the battery (or side) if you want to keep one as spare.
Could you post a pic, as I'm trying to figure out the best way to bend it?
Thanks -
Look like I modded it again after to use the other cell, but moved the switch side positive contact instead (outside of the red switch 'channel':

This way it works with 1 battery in either location. A spare can be carried, but MUST face the same direction (+ side up) or it will short when the switch is turned on.

Bend the negative tip up to touch the door contact. Make it go over the battery IF you want to store a spare batt there. I did not do that, just bent the neg contact up to touch the lid contact and could only use the outer battery location like that.
If you don't want to make it permanent, just stick a small ball of foil in there to make the contact. Just means you can't carry a spare.

Both lites are ON:

Light from my monitor about 2' away overpowers the light about 1' away from the wall.
-
Glad it worked. Such a simple mod and it makes the tool soo much more usable. I feel like the light is very overlooked.
I put one in an explorer instead of the mag. It might be my favorite toolset.
-
It is pretty common to run "3V" LEDs on 2 x 3V button cells in series, look at any "Fauxton" as an example. When in use not many 3V button cells will supply a full 3V for very long, and over-driving the LED does give a lot more light.
Most reasonable quality LEDS will survive being over-driven for short(ish) periods. They might not last the usual 40-50,000 hours, but that isn't a serious problem for most people.
If you want an LED that will work OK on one 3V battery look at yellow or red LEDs, these seem to work better on lower voltages than white LEDs.
-
@armi101 said:
Glad it worked. Such a simple mod and it makes the tool soo much more usable. I feel like the light is very overlooked.I put one in an explorer instead of the mag. It might be my favorite toolset.
I haven't modded the LED just yet! I gotta order some for future builds...
And I agree with you on the Lite modules...I'd like to put one in almost every mod. I have lots of Spartan Lites for donors. One with the new clear case, a few with the newer '12+ gray case and several with the original '04 type.
-
I don't know why I didn't think of this before, but to use one battery you don't need to change anything apart from have both batteries facing positive upwards! No wire bending required.

The conductor on the door effectively uses the metal of the second battery as a conductor so only the battery nearest the led is actually used. The one furthest away isn't used as the negative is not connected to anything so that's the spare one.
Bingo, 3v instead of 6v.

-
@craggus2000 said:
I don't know why I didn't think of this before, but to use one battery you don't need to change anything apart from have both batteries facing positive upwards! No wire bending required.
The conductor on the door effectively uses the metal of the second battery as a conductor so only the battery nearest the led is actually used. The one furthest away isn't used as the negative is not connected to anything so that's the spare one.
Bingo, 3v instead of 6v.

:D
Always nice when the light comes on!

-
And just for those interested in the dates and history, The new case shows up in '12 , but the newer brighter LED shows up in '13 and the clear one I have is dated '17.
-
@craggus2000 said:
I don't know why I didn't think of this before, but to use one battery you don't need to change anything apart from have both batteries facing positive upwards! No wire bending required.
The conductor on the door effectively uses the metal of the second battery as a conductor so only the battery nearest the led is actually used. The one furthest away isn't used as the negative is not connected to anything so that's the spare one.
Bingo, 3v instead of 6v.

Awesome!

-
@craggus2000 said:
I don't know why I didn't think of this before, but to use one battery you don't need to change anything apart from have both batteries facing positive upwards! No wire bending required.
The conductor on the door effectively uses the metal of the second battery as a conductor so only the battery nearest the led is actually used. The one furthest away isn't used as the negative is not connected to anything so that's the spare one.
Bingo, 3v instead of 6v.

Hi fellas,
So I have a Spartan Lite that I would like to mod as well. I have plenty of 3.6v LED's to work with. My question is more how to get the whole thing apart. Do I have disassemble the entire knife to get at the LED bulb? I've never taken apart a SAK before and it seems daunting. Also, if I understand correctly I pretty much just have to flip the rear battery around and now the LED is running off just one battery and now there is a spare? Thanks for any and all clarifications!
-
You have to take it apart to change the led.
One thing ive been thinking about. I wonder why victorinox hasn't done this themselves. Really they could keep eveything the same and change the led to a higer mcd and it improves the utility of the flashlight. The tool set doest have to change.
From what i have read of reviews of the spartan lite most complaints are weak light, and expensive batteries. I wonder if the batteries would seem so expensive if the light worked better..
Id like to see.
Climber lite
Compact lite (this was a mod I did)
Explorer lite -
@armi101 said:
You have to take it apart to change the led.One thing ive been thinking about. I wonder why victorinox hasn't done this themselves. Really they could keep eveything the same and change the led to a higer mcd and it improves the utility of the flashlight. The tool set doest have to change.
From what i have read of reviews of the spartan lite most complaints are weak light, and expensive batteries. I wonder if the batteries would seem so expensive if the light worked better..
Id like to see.
Climber lite
Compact lite (this was a mod I did)
Explorer liteThe newer Lites starting sometime in '13 are brighter! I posted about that earlier. Not super bright, but definitely brighter than earlier models.
I agree with your suggestion for more models with the lite module. There is sort-of a Climber lite with the late model Traveller (and older Voyager), but it also comes with electronic scales. I love mine and do use them on trips.
I have a tendency to want Lites on larger models too. I modded a Troubleshooter with a Lite and think they should make a Champion and Champ Lite too. I like my CT lite, but it's missing both saws and I think a CT41 Lite would be too big. I'm working on another mod now that will be pretty big and include a lite.
-
So I did the led mod a few days ago to fit in to a sak mod I've just finished (more on that in a few days >:D ) and the results are astounding!
The 2 pics below were taken in an otherwise pitch black room. I forgot to take 'before' pics, but needless to say the original led was like a p***hole in the snow.
Also the new led runs on 1x 3v battery so I can carry a spare within the lite module now



-
@craggus2000 said:
So I did the led mod a few days ago to fit in to a sak mod I've just finished (more on that in a few days >:D ) and the results are astounding!The 2 pics below were taken in an otherwise pitch black room. I forgot to take 'before' pics, but needless to say the original led was like a p***hole in the snow.
Also the new led runs on 1x 3v battery so I can carry a spare within the lite module now

Wow, that is phenomenal! So I really want to do this mod on my spartan lite. I have plenty of LED's (I work on circuit boards used in music equipment) but I have never taken apart a SAK before. Do I need parts to reassemble the knife? From the little research I've done it seems I will need to drill out the brass pins. Thanks in advance for the help!
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login