The small blade?
-
@Harris said:
I would like to see the sheeps-foot blade from the Radio Shack Electrician on a Spartan or Tinker as a replacement for the small pen blade, or even as the only blade on a Compact or Walker.+10
That's an excellent idea right there

Never quote understand why Vic never thought of this for some models. Especially the Tinkers, they could be much more and actually "Tinker-ish" than they are on lots of tools. Most of the difference between the other models is only the inclusion of the Philips on the back instead of the CS.
I have to give it to Wenger, they where a lot more inventive and adventurous there....
-
@El Corkscrew said:
I would carry an alox electrician or apprentice more often if it had a key ring. I'm so used to using el pocket clip now it feels weird with out it. Have you thought about the electrician?a
I like SAKs without the lanyard ring, but the TL-29 and hawkbill, both patterns traditionally carried by linemen and electricians have huge bails you can put any kind of cord/rope through (when I'm working around the farm, I usually secure them by means of a carabiner to my belt). So you'd think the Electrician and Apprentice would have a keyring to prevent loss, as they're largely intended for use by the same people as the TL-29 and hawkbill. -
@El Corkscrew said:
I would carry an alox electrician or apprentice more often if it had a key ring. I'm so used to using el pocket clip now it feels weird with out it. Have you thought about the electrician?
a
I like SAKs without the lanyard ring, but the TL-29 and hawkbill, both patterns traditionally carried by linemen and electricians have huge bails you can put any kind of cord/rope through (when I'm working around the farm, I usually secure them by means of a carabiner to my belt). So you'd think the Electrician and Apprentice would have a keyring to prevent loss, as they're largely intended for use by the same people as the TL-29 and hawkbill.
I like being able to hang my knives from belt loops or pocket clips. It's also good to be able to have some lanyard, albeit small, to increase grip or use as wrist loop, to prevent dropping the knife.

-

I’d rather have and not need, than to need and not have. If you don’t like it, grind it off.
-
... still, I like to keep- if 2 blades- the small one un-used, for various reasons....

-
Big for food, small for dirty stuff.
-
This plus a zillion or two!

One more here for the small blade for primary use. I use the main blade for food...and mostly to cut sandwiches and burgers at picnics and BBQs.
I think there should be more options for the the blades to be swapped. Small blades on the main blade side only need the proper spacer from the factory. I'd buy knives with a small blade and a pruner or electrician blade. Small + Pruner is on my list of upcoming mods now that I have a few donors in stock. What I'd really like is a gardener sized Hawkbill and the small pen blade.
-
I use the small blade mainly to open blister packs. Less chance to damage the item inside. Same applies to open packages, even though i mainly use the can opener on my wenger classic for that purpose nowadays.
-
I reserve the small blade for fine and intricate cutting, and keep it as sharp as possible.
I find the 84mm and 91mm large blades too small and too awkward for general food prep. The extra belly of the 85mm knives works much better for cutting and slicing on a board, but the blade is still often too short.
If I need a SAK for food prep I use a 111mm instead.
-
I feel another useless poll coming on but I'll spare you guys

-
I like to keep the edge bevel on the small blade ridiculously thin, around 6 degrees per side or less and hair-splittingly sharp. If used gently it makes a multitude of cutting tasks really easy.
If it touches your skin though, you bleed :ahhh -
DMT diamond hones for profiling and sharpening dullish edges and finish on a Spyderco ultra-fine ceramic that I lapped with a DMT fine hone to make it even smoother, crazy sharp.
-
One more here for the small blade for primary use. I use the main blade for food...and mostly to cut sandwiches and burgers at picnics and BBQs.
I think there should be more options for the the blades to be swapped. Small blades on the main blade side only need the proper spacer from the factory. I'd buy knives with a small blade and a pruner or electrician blade. Small + Pruner is on my list of upcoming mods now that I have a few donors in stock. What I'd really like is a gardener sized Hawkbill and the small pen blade.
How hard would it be to make a two layer with big+small and pruner+electrician with an awl on the back? That would be one heck of a lot of cutting utility in a small package.
-
@pomsbz said:
How hard would it be to make a two layer with big+small and pruner+electrician with an awl on the back? That would be one heck of a lot of cutting utility in a small package.Not hard at all with the right donor parts. Pre-'85 spring would be easiest and would only need the right spacers for both blades ~0.5mm for both sides. If a knife layer spring is used, then 1mm spacers could be used and the awl would need a ~0.5mm spacer too.
I think it would be a good knife...
-
@pomsbz said:
How hard would it be to make a two layer with big+small and pruner+electrician with an awl on the back? That would be one heck of a lot of cutting utility in a small package.Well, it wouldn't be SAK, but something like a Case Congress already packs four blades into one smallish knife. There are even a few 5-blade trappers and sowbellys floating around, but I believe they were all special runs.
-
@nate j said:
Well, it wouldn't be SAK, but something like a Case Congress already packs four blades into one smallish knife. There are even a few 5-blade trappers and sowbellys floating around, but I believe they were all special runs.True but these four blades are IMO a better overall package and of course you get the package of super stainless, easy to sharpen and great form factor.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login