PowerPint Overview Mighty Little MT
-
Something like the Kershaw A100's would work, maybe on the other side of where the Pint's pocket-clip is.
put a latch on one screw, and have a narrow washer to lift the screw's head, so the latch can hook it.

-
@Sam Lim said:
I would really like to incorporate some kind of swing lock for the handles..
Show us how it's done, Sam.
-
@ReamerPunch said:
Something like the Kershaw A100's would work, maybe on the other side of where the Pint's pocket-clip is.
put a latch on one screw, and have a narrow washer to lift the screw's head, so the latch can hook it.This sounds like a good idea ReamerPunch! All we need is to source a suitable latch that will fit, if not it has to be custom-made?
Gosh, I wish SOG is listening !
-
@roamingcat said:
This sounds like a good idea ReamerPunch! All we need is to source a suitable latch that will fit, if not it has to be custom-made?Gosh, I wish SOG is listening !
I think it would be easy to fabricate from some mild hardness thinner gauge steel. Using a dremel and assorted cutting wheels and bits. And a lot of patience. :ahhh
-
@gerleatherberman said:
I think it would be easy to fabricate from some mild hardness thinner gauge steel. Using a dremel and assorted cutting wheels and bits. And a lot of patience. :ahhhThanks for the tip! Has anyone disassembled the torx screws, took out the implements and put it all back together in their Pint yet? How easy/difficult is it to put the tension springs back together?
-
@roamingcat said:
Thanks for the tip! Has anyone disassembled the torx screws, took out the implements and put it all back together in their Pint yet? How easy/difficult is it to put the tension springs back together?Anytime! Should be a fun project.

It is one of the easier tools to break down and put back together(relatively of course). The only issue I would mark as somewhat serious is the thin washers. Make sure they do back between the correct implements. The newer versions have better quality washers, but if you have an early Pint, they will be thin and flimsy. Just something to watch for. :) -
@gerleatherberman said:
Anytime! Should be a fun project.
It is one of the easier tools to break down and put back together(relatively of course). The only issue I would mark as somewhat serious is the thin washers. Make sure they do back between the correct implements. The newer versions have better quality washers, but if you have an early Pint, they will be thin and flimsy. Just something to watch for. :)Like GLBM said. The spring does not post any problems. I think mine is a earlier version. The washers are a complete mess..

-
I hope SOG has been taking notes.

-
@gerleatherberman said:
Anytime! Should be a fun project.
It is one of the easier tools to break down and put back together(relatively of course). The only issue I would mark as somewhat serious is the thin washers. Make sure they do back between the correct implements. The newer versions have better quality washers, but if you have an early Pint, they will be thin and flimsy. Just something to watch for. :)Thanks guys for your advice
. I will take note and be extra careful with the washers. Fingers-crossed. 
-
Great thread guys. Just coming across this now. Do any of you have a feel for whether Victorinox or Wenger tools might fit?

-
No idea about the Vic tools fitting, but thanks for the kind words, tommywp!

-
Not ideal, but a quick & dirty method to prevent the handles from opening while riding on the pocket clip. Cut out a U clip from a paper clip.


-
Cool hack, roamingcat!

-
@gerleatherberman said:
Cool hack, roamingcat!
Thank you ! Applied the same hack to solve the same 'problem' of my LM Wave while I am at it.

-

A couple of questions though, if you don't mind?! Do you ever lose the clips? And how long does a nice one take to make?
-
A couple of questions though, if you don't mind?! Do you ever lose the clips? And how long does a nice one take to make?
Sure, not at all. I haven't lost a clip yet, but it is mainly because I only had it for less than 24 hours and I haven't been carrying it around too much
I agree with you it may be prone to loosing since there is no permanent attachment to the Pint. fyi I made the first u-clip in about a minute, and if I ever loose it I can re-make a replacement in less than a minute since I am already familiar with the overall shape. All that is required is a paper clip, 2 cuts + 2 bends (with one finger and one set of pliers) btw - I have further 'refined' the u-clip in the attached photo. It has worked well for me so far (within the last 24 hous or so).
-
double post
-
Great simple idea

-
@roamingcat said:
Sure, not at all. I haven't lost a clip yet, but it is mainly because I only had it for less than 24 hours and I haven't been carrying it around too much
I agree with you it may be prone to loosing since there is no permanent attachment to the Pint. fyi I made the first u-clip in about a minute, and if I ever loose it I can re-make a replacement in less than a minute since I am already familiar with the overall shape. All that is required is a paper clip, 2 cuts + 2 bends (with one finger and one set of pliers) btw - I have further 'refined' the u-clip in the attached photo. It has worked well for me so far (within the last 24 hous or so).Excellent. Thank you, RC!

I may conjure up a few clips for some looser tools now. A minute or so seems like a fair compromise to keep certain tools from opening on the pocket. I have usually just over tightened pliers pivot bolts to keep them from opening, but flipping MTs open when they arw looser. :)
-
I want to love this tool so badly... perfect size, good tool selection (short of flat head drivers)... but the small flathead that is onboard bends at will and is seemingly made of pot metal... the scissors leave a lot to be desired as well... I am in love with the design, just wish it was executed better!
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login