PowerPint Overview Mighty Little MT
-

A couple of questions though, if you don't mind?! Do you ever lose the clips? And how long does a nice one take to make?
-
A couple of questions though, if you don't mind?! Do you ever lose the clips? And how long does a nice one take to make?
Sure, not at all. I haven't lost a clip yet, but it is mainly because I only had it for less than 24 hours and I haven't been carrying it around too much
I agree with you it may be prone to loosing since there is no permanent attachment to the Pint. fyi I made the first u-clip in about a minute, and if I ever loose it I can re-make a replacement in less than a minute since I am already familiar with the overall shape. All that is required is a paper clip, 2 cuts + 2 bends (with one finger and one set of pliers) btw - I have further 'refined' the u-clip in the attached photo. It has worked well for me so far (within the last 24 hous or so).
-
double post
-
Great simple idea

-
@roamingcat said:
Sure, not at all. I haven't lost a clip yet, but it is mainly because I only had it for less than 24 hours and I haven't been carrying it around too much
I agree with you it may be prone to loosing since there is no permanent attachment to the Pint. fyi I made the first u-clip in about a minute, and if I ever loose it I can re-make a replacement in less than a minute since I am already familiar with the overall shape. All that is required is a paper clip, 2 cuts + 2 bends (with one finger and one set of pliers) btw - I have further 'refined' the u-clip in the attached photo. It has worked well for me so far (within the last 24 hous or so).Excellent. Thank you, RC!

I may conjure up a few clips for some looser tools now. A minute or so seems like a fair compromise to keep certain tools from opening on the pocket. I have usually just over tightened pliers pivot bolts to keep them from opening, but flipping MTs open when they arw looser. :)
-
I want to love this tool so badly... perfect size, good tool selection (short of flat head drivers)... but the small flathead that is onboard bends at will and is seemingly made of pot metal... the scissors leave a lot to be desired as well... I am in love with the design, just wish it was executed better!
-
The last SOG MT I bought, and I don't even remember the name [it was the PowerAccess], was so poorly made that I dropped out of an MTO Challenge and returned the thing to Amazon. The "file" was as smooth as a baby's rump, and the whole thing was just flimsy and cheap.
-
@DeezNittles said:
I want to love this tool so badly... perfect size, good tool selection (short of flat head drivers)... but the small flathead that is onboard bends at will and is seemingly made of pot metal... the scissors leave a lot to be desired as well... I am in love with the design, just wish it was executed better!I have not experienced any driver bending yet, but will watch for it. Thanks for the input, Nittles!

-
@powernoodle said:
The last SOG MT I bought, and I don't even remember the name [it was the PowerAccess], was so poorly made that I dropped out of an MTO Challenge and returned the thing to Amazon. The "file" was as smooth as a baby's rump, and the whole thing was just flimsy and cheap.Indeed. I did have fun smearing mayonnaise on bread with the file though.

Here is the PowerAccess Deluxe/PowerAccess challenge thread for anyone interested in our observations of its' performance. :)
/topic/77168That said, and I'm being honest, it would be nice to keep this thread about the PowerPint and ideas to improve the function of it. :)
-
@powernoodle said:
The last SOG MT I bought, and I don't even remember the name [it was the PowerAccess], was so poorly made that I dropped out of an MTO Challenge and returned the thing to Amazon. The "file" was as smooth as a baby's rump, and the whole thing was just flimsy and cheap.When the PowerPint was annouced I was pretty sure I would get one but held off waiting to hear some reports. I no longer intend to get one because I expect to be disappointed and I'm not all the picky. SOG has some great ideas and clever designs but they seriously need to up their manufacturing game before I will ever buy again.
-
@powernoodle said:
The last SOG MT I bought, and I don't even remember the name [it was the PowerAccess], was so poorly made that I dropped out of an MTO Challenge and returned the thing to Amazon. The "file" was as smooth as a baby's rump, and the whole thing was just flimsy and cheap.I may be the odd one to like the file on the Pint. Tool this size, I wouldn't expect it to file hard stuffs. Able to round off plastic or wood is good enough. Works best for manicure. Great pocket nail file for touching up.

-
Inspired by the new LM Free, I found a 1mm magnet and used it as a stopper to the handles from opening. A slightly more 'elegant' solution to the 'paper clip' method imo.


-
:o
Very very cool, RC!
What kind of magnet did you use for the mod?
-
@gerleatherberman said:
:o
Very very cool, RC!
What kind of magnet did you use for the mod?
For the Pint, I used one 10 x 1mm round magnet. For the LM Wave, I used 2 small 3 x 1.5mm round magnets. I applied double-sided adhesive tape to one side of the magnet to secure it from moving. These are very strong magnets, together with the double-sided adhesive tape I find it very secure and greatly minimize the risk of loosing it.
If you cannot find some spare magnets already stuck on your fridge that you can use, you should be able to source some from your local hardware store or from Amazon. Just do a search for, say, 1mm magnet and there are plenty of choices of many different shapes and sizes.
I am quite happy with the result as it requires almost no effort to fix the issue of the loose handles from opening up.

-
Thanks for the explanation, RC!

-
Thanks for the explanation RC!
Great to know that other members are trying to improve on this little but mighty MT. 
I thought up with a mechanical solution for this. A locking latch, beta stage. It somewhat resembles a horse head..
but works wonderfully.Down side, the tools on the swinging latch side cannot open when the latch is engaged due to the locking tab cannot extend backwards. No biggie. The latched side open with no issue.
Pics below on how it latches.
Latch click into place.


I have to modify a thicker washer with thinner "walls" to allow the latch to enter.


Latched side, tools deploys no issue.

For now, when unused, it disappears into the frame so I have to open up the other tools to dig it out. Doesn't really bother me yet.

Where this part came from? The clip is not tempered and can bend to ridiculous shapes without breaking. Using the larger hole for the pivot. I hate drilling... :P


-
Wonderful solution, Sam!

Looks like how SOG should have done it at the factory. I like it better than the PowerLitre latch, and I like the PowerLitre latch.

-
@gerleatherberman said:
Wonderful solution, Sam!
Looks like how SOG should have done it at the factory. I like it better than the PowerLitre latch, and I like the PowerLitre latch.

could u snap a pic for the latch on the PL? I can't see it on all the stock photos. 
-
It is somewhere in the photos I took for this thread.
/post/1777635
-
@gerleatherberman said:
It is somewhere in the photos I took for this thread.
/post/1777635
Just saw that!
thanks! Is that plastic?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login