The Hacked Leatherman Owners Club.
-
That's one way...but not the cleanest or fastest. I need to make a vid of the method. You need to break the lip of the lid so that it releases from the can.
On a side note, I think I'm narrowing down a set of Leatherman knife setups for different activities.
https://www.instagram.com/p/BwYOXYKgcEC/?utm_source=ig_share_sheet&igshid=18vue5ncab5vm -
@Happy Gilmore said:
That's one way...but not the cleanest or fastest. I need to make a vid of the method. You need to break the lip of the lid so that it releases from the can.On a side note, I think I'm narrowing down a set of Leatherman knife setups for different activities.
https://www.instagram.com/p/BwYOXYKgcEC/?utm_source=ig_share_sheet&igshid=18vue5ncab5vm
so what do u do with the pliers? 
I just can't get used to half tools..yet.. So I assembled every thing back...
-
Love that mod, Synco

Great family pic of the LM knives, HG

The Charge/Wave/Surge knives are great for me (need to make a SURGE one
:D ) but I can see that they have plenty of limits and that is why I normally carry mine as a compliment to a regular MT 
-
@Poncho65 said:
Love that mod, Synco
Great family pic of the LM knives, HG

The Charge/Wave/Surge knives are great for me (need to make a SURGE one
:D ) but I can see that they have plenty of limits and that is why I normally carry mine as a compliment to a regular MT 
actually I put the surge back together..I just can't see how a surge/ST300 hybrid ever makes sense. The shears on the Surge are unlike any other scissors on a MT, and unlike even the biggest of the Vic Scissors, it can cut some stupidly hard materials. I did however put it back together with sissors on the same side as the straight blade so I can easily open it one handed from the same pocket position. One thing would make it perfect in my mind...a full 1/4 inch bit driver instead of the Serrated blade on the outside... Think a Center drive, without the suck... I have reason to believe that the Center drive 1/4 inch driver might even work in the surge.
Cheers,
H.G. -
-
@Happy Gilmore said:
I have reason to believe that the Center drive 1/4 inch driver might even work in the surge.Perhaps a SOG one?
Easier to obtain. https://www.sogknives.com/type/accessories/1-4-driver.html -
@Syncop8r said:
Perhaps a SOG one?
Easier to obtain. https://www.sogknives.com/type/accessories/1-4-driver.htmlThe one handed part is what is so appealing imo. Plus that requires an intermediary socket holder so its not going to be all that stable. At that points I might as well just carry a Leatherman Bit extender.
@ReamerPunch said:
Still better than the BuckTool.
yea, that one was shi...err...crappy... at least I now know for sure there is a relatively efficient way to open cans with just pliers. (check general discussion forum)
Cheers,
H.G. -
So... Did my thinking, pondering..and just did it.
Still needs two mods to the bit drivers and a Vic scissor but it's a thing of beauty
-
Nice HG.

-

So what all did you do in this mod
I believe it is bi-colored but it is a bit hard to tell in the pics 
-
So what all did you do in this mod
I believe it is bi-colored but it is a bit hard to tell in the pics 
So it is noticably different from the bicolor model for a number of reasons. As far as internal tools are concerned I used large spaces on one side to accomidate a modified bit driver after I cut out the sides. On the other side I need to drill a small hole through the bit driver in a specific location (still working it out) so that I can lock a series of T-shank bits and blades in there in addition to the normal tools.
Eventually I should have:
1/4" bit driver (straight blade side)
AWL
Hybrid bit driver-
*takes leatherman bits
*takes T-shank blades (locks in with small clip or even a paper clip)
*takes exacto blades (using simple adapter)And once I get a 91mm Vic scissor I can begin working on replacing the serrated blade.
So this is a work in progress but I wanted to see how it looked before I finished it. I also want to gently grind down the lock connections so that I can close it one handed, not just open it one handed.
Cheers,
HG -
I like the bi-color part
Hope that the 1/4 inch bit holder works out the way you want and you can get some 91mm Vic scissors in 
-
Today's carry and the 1/4 inch driver mod. Thank God for a Dremel tool.
Cheers,
HG -
That is great
but I hope that cutting the notch didn't compromise the strength of the bit driver :ahhh keep us updated on how this particular mod holds up
if it does then AWESOME :D if not then........... 
:D
-
@Poncho65 said:
That is great
but I hope that cutting the notch didn't compromise the strength of the bit driver :ahhh keep us updated on how this particular mod holds up
if it does then AWESOME :D if not then........... 
:D
I can tell already that it is substantially weaker, but does work for all buy stubborn screws and a hard crank. For me that's not acceptable. So I'll try a different solution.
-
My halfBlast suffered some mods, added a Tshank for longersaw.

-
Nice one Raoul

-
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
