Leatherman Free P2/P4 Club and Feedback Thread
-
@Sea Monster said:
How does it go as a knife?
I've found most multis (some more than others - the MP600 can sod right off) have "acceptable" knives for utilitarian tasks, but hardly a pleasure to use - does the P2/P4 have the ergonomics and blade design to really feel like a decent knife in hand?In my opinion, the knife is more comfortable than the knife on the Charge. I also like the blade shape better. If they come out with an S30v version, it would be the best knife on any multitool I’ve handled.
Sent from my iPad using Tapatalk
-
@gadgetman7 said:
In my opinion, the knife is more comfortable than the knife on the Charge. I also like the blade shape better. If they come out with an S30v version, it would be the best knife on any multitool I’ve handled.Sent from my iPad using Tapatalk

-
I was thinking about getting a new Charge+ when I saw the reports from SHOT show about the new Free line. The SHOT show videos didn't really give enough information, so I very much appreciate the posts here and the videos linked in these posts. I like the one handedness of the Free models, but I think I'm going to stick with the Charge+. It will be a few weeks before I place an order, so feel FREE to change my mind. Here are my reasons:
The Free P4 and Charge+ cost the same amount.
The Charge+ has a 154CM blade
The Charge+ has both blades easily accessible ( serrated and plain edge ), and right handed
The Charge+ has bit holders
The Charge+ has a longer file, and a diamond coating.The Free has an awl, a better can opener, a package opener, and maybe better scissors.
The Charge has a better plain edge blade, a longer serrated blade, a longer saw, a better file and longer file, and bit drivers.I'm not sold on the 2 and a half D phillips driver, the 420HC plain edge blade, or the funky file. Perhaps there will be a Free P4+ with bit drivers and a diamond file in the future? Anyway, I would love to hear more opinions and will try to keep an eye on this forum. Thanks for all the input so far.
-
Why do they insist on two blades? Ditch the serrated, and have a proper file.
-
I only need one blade on a MT and
a longer file would make much more sense
-
Toss my vote in for the file over SE blade as well. And then put a short SE blade, like the Sidekick, in the tiny file slot. Then swap the giant phillips for a longer, redesigned bit exchanger.
Call it the "Free P-Pro".
-
Sounds like a good MT to me

-
@gerleatherberman said:
Toss my vote in for the file over SE blade as well. And then put a short SE blade, like the Sidekick, in the tiny file slot. Then swap the giant phillips for a longer, redesigned bit exchanger.
Call it the "Free P-Pro".

-
@gerleatherberman said:
Toss my vote in for the file over SE blade as well. And then put a short SE blade, like the Sidekick, in the tiny file slot. Then swap the giant phillips for a longer, redesigned bit exchanger.
Call it the "Free P-Pro".
I like this idea. I’d add the blade exchanger for the saw too.
Sent from my iPad using Tapatalk
-
Nice pics and reviews gents! I have not seen one in person yet, but by the pics it looks sweet. Love seeing USA stamped on it also. The only concern I have it the amount of metal that it might collect on the magnets. Don't know, maybe the metal shaving will clean off easy.
Anyways, thanks for sharing guys.
-
@ducttapetech said:
maybe the metal shaving will clean off easy.I reckon it will, Nate.
While the magnets may attract stuff, opening up all the tools and cleaning it out, does look to be quite straightforward. -
@AimlessWanderer said:
I reckon it will, Nate.
While the magnets may attract stuff, opening up all the tools and cleaning it out, does look to be quite straightforward.That is what I am thinking.
Anybody modded theirs yet?
:D -
First thing I would do is re-shaping the awl's tip, like I did on my Spirit. I like it poky :D
... pics show before & after...



-

It doesn't seem hard to reprofile the P4 awl screwdriver tip into a real awl tip.
There was a nice photo of a Surge reamer and P4 awl somewhere but I can't find it now. But it should not be much of a problem.Not sure why the awl has a screwdriver tip, though. But the quarter-circle can opener doesn't?

-
Great awl shape, Matt!

The P series awl looks like a good candidate for sharpening the tip. The driver tip on the file would likely be small enough for most flat drive screws.
AW,
Good point on the ease of clean. I got some steel wool dust on the retainer magnet housing, inside the tool, earlier today and was able to clean it off with packing tape. Duct tape would work as well I think.Good thing is the tool isn't as complicated as it would appear. The magnetic systems appear to be removeable and replaceable if any issues arise. The retainer case comes out with the lock spring and pivot. The pliers closure casing slips out when the pivot is removed. I haven't tried loosening the pivot yet to take it apart, but will do so at some point and take photos.
-
@gerleatherberman said:
Great awl shape, Matt!
The P series awl looks like a good candidate for sharpening the tip. The driver tip on the file would likely be small enough for most flat drive screws.
AW,
Good point on the ease of clean. I got some steel wool dust on the retainer magnet housing, inside the tool, earlier today and was able to clean it off with packing tape. Duct tape would work as well I think.Good thing is the tool isn't as complicated as it would appear. The magnetic systems appear to be removeable and replaceable if any issues arise. The retainer case comes out with the lock spring and pivot. The pliers closure casing slips out when the pivot is removed. I haven't tried loosening the pivot yet to take it apart, but will do so at some point and take photos.
Thanks

And good idea using take to remove the steel wool dust

Looking forward to the pivot details

-
Howdy folks,
I received my Free P4.
I took a ton of photos comparing the tool to the Charge, as well as took it apart.
Here is a link to the exploded view.Here is the gallery of images.
My biggest gripes are the small file and lack of bit-driver. I am planning a few mods, and I am currently working on a detailed 3D model of the Free P4. I will use this to design a custom fit holster. I do think it is overpriced, but I really like the magnetic opening/closing. I hate needing two hands and finger nails to use my Charge. The P4 will probably become my EDC tool because it is also slimmer than the Charge TTI.
Magnets:
The magnets are 0.251"x0.511"x0.640" (6.37mmx13mmx1.60mm)
The magnets themselves are quite strong for their size. They seem to be high quality. They had small plastic guard, presumably to prevent the magnets from smacking into each other, which is great as Neodymium magnets aren't actually solid silvery metal as many think, they usually compressed powder which is nickel plated, and can break open.
On the inside of the tool the magnets make contact with the flat surface on each of the tools while folded. The magnets will probably pull away any metal shaving from getting into the hinges, but then any build up will collect on this mating surface. The good news is it is exposed enough with the tools deployed that you can probably get in and clean the magnet surface with a stronger magnet.
The magnets are secured by the thin metal springs in the tool. The little plastic bit doesn't do anything to hold them in place. I bet the plastic just makes it easier to clean off dust.
They can be replaced by require taking apart the whole tool.
Possible replacement magnet for future reference, and N52 model
Modifying the tool:
The tool is just a stack-up of parts around chicago screws, you can probably take the tool apart and re-arrange the tools if you want. The screws have strong lock-tite on the threads.
The small screws and lanyard/belt clip screws are #2-56, the larger screws are #6-40. -
@ZapWizard said:
Howdy folks,I received my Free P4.
I took a ton of photos comparing the tool to the Charge, as well as took it apart.
Here is a link to the exploded view.Here is the gallery of images.
My biggest gripes are the small file and lack of bit-driver. I am planning a few mods, and I am currently working on a detailed 3D model of the Free P4. I will use this to design a custom fit holster. I do think it is overpriced, but I really like the magnetic opening/closing. I hate needing two hands and finger nails to use my Charge. The P4 will probably become my EDC tool because it is also slimmer than the Charge TTI.
Magnets:
The magnets are 0.251"x0.511"x0.640" (6.37mmx13mmx1.60mm)
The magnets themselves are quite strong for their size. They seem to be high quality. They had small plastic guard, presumably to prevent the magnets from smacking into each other, which is great as Neodymium magnets aren't actually solid silvery metal as many think, they usually compressed powder which is nickel plated, and can break open.
On the inside of the tool the magnets make contact with the flat surface on each of the tools while folded. The magnets will probably pull away any metal shaving from getting into the hinges, but then any build up will collect on this mating surface. The good news is it is exposed enough with the tools deployed that you can probably get in and clean the magnet surface with a stronger magnet.
The magnets are secured by the thin metal springs in the tool. The little plastic bit doesn't do anything to hold them in place. I bet the plastic just makes it easier to clean off dust.
They can be replaced by require taking apart the whole tool.
Possible replacement magnet for future reference, and N52 model
Modifying the tool:
The tool is just a stack-up of parts around chicago screws, you can probably take the tool apart and re-arrange the tools if you want. The screws have strong lock-tite on the threads.
The small screws and lanyard/belt clip screws are #2-56, the larger screws are #6-40.Bravo!!! Well done.It looks like the elastomer bushings could pretty easily be DIY replaced, if necessary.
-
Well done Zap and welcome to the forum !

I'm going to put this here just cause it's cool


Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login