Leatherman Free P2/P4 Club and Feedback Thread
-
@gerleatherberman said:
Toss my vote in for the file over SE blade as well. And then put a short SE blade, like the Sidekick, in the tiny file slot. Then swap the giant phillips for a longer, redesigned bit exchanger.
Call it the "Free P-Pro".
I like this idea. I’d add the blade exchanger for the saw too.
Sent from my iPad using Tapatalk
-
Nice pics and reviews gents! I have not seen one in person yet, but by the pics it looks sweet. Love seeing USA stamped on it also. The only concern I have it the amount of metal that it might collect on the magnets. Don't know, maybe the metal shaving will clean off easy.
Anyways, thanks for sharing guys.
-
@ducttapetech said:
maybe the metal shaving will clean off easy.I reckon it will, Nate.
While the magnets may attract stuff, opening up all the tools and cleaning it out, does look to be quite straightforward. -
@AimlessWanderer said:
I reckon it will, Nate.
While the magnets may attract stuff, opening up all the tools and cleaning it out, does look to be quite straightforward.That is what I am thinking.
Anybody modded theirs yet?
:D -
First thing I would do is re-shaping the awl's tip, like I did on my Spirit. I like it poky :D
... pics show before & after...



-

It doesn't seem hard to reprofile the P4 awl screwdriver tip into a real awl tip.
There was a nice photo of a Surge reamer and P4 awl somewhere but I can't find it now. But it should not be much of a problem.Not sure why the awl has a screwdriver tip, though. But the quarter-circle can opener doesn't?

-
Great awl shape, Matt!

The P series awl looks like a good candidate for sharpening the tip. The driver tip on the file would likely be small enough for most flat drive screws.
AW,
Good point on the ease of clean. I got some steel wool dust on the retainer magnet housing, inside the tool, earlier today and was able to clean it off with packing tape. Duct tape would work as well I think.Good thing is the tool isn't as complicated as it would appear. The magnetic systems appear to be removeable and replaceable if any issues arise. The retainer case comes out with the lock spring and pivot. The pliers closure casing slips out when the pivot is removed. I haven't tried loosening the pivot yet to take it apart, but will do so at some point and take photos.
-
@gerleatherberman said:
Great awl shape, Matt!
The P series awl looks like a good candidate for sharpening the tip. The driver tip on the file would likely be small enough for most flat drive screws.
AW,
Good point on the ease of clean. I got some steel wool dust on the retainer magnet housing, inside the tool, earlier today and was able to clean it off with packing tape. Duct tape would work as well I think.Good thing is the tool isn't as complicated as it would appear. The magnetic systems appear to be removeable and replaceable if any issues arise. The retainer case comes out with the lock spring and pivot. The pliers closure casing slips out when the pivot is removed. I haven't tried loosening the pivot yet to take it apart, but will do so at some point and take photos.
Thanks

And good idea using take to remove the steel wool dust

Looking forward to the pivot details

-
Howdy folks,
I received my Free P4.
I took a ton of photos comparing the tool to the Charge, as well as took it apart.
Here is a link to the exploded view.Here is the gallery of images.
My biggest gripes are the small file and lack of bit-driver. I am planning a few mods, and I am currently working on a detailed 3D model of the Free P4. I will use this to design a custom fit holster. I do think it is overpriced, but I really like the magnetic opening/closing. I hate needing two hands and finger nails to use my Charge. The P4 will probably become my EDC tool because it is also slimmer than the Charge TTI.
Magnets:
The magnets are 0.251"x0.511"x0.640" (6.37mmx13mmx1.60mm)
The magnets themselves are quite strong for their size. They seem to be high quality. They had small plastic guard, presumably to prevent the magnets from smacking into each other, which is great as Neodymium magnets aren't actually solid silvery metal as many think, they usually compressed powder which is nickel plated, and can break open.
On the inside of the tool the magnets make contact with the flat surface on each of the tools while folded. The magnets will probably pull away any metal shaving from getting into the hinges, but then any build up will collect on this mating surface. The good news is it is exposed enough with the tools deployed that you can probably get in and clean the magnet surface with a stronger magnet.
The magnets are secured by the thin metal springs in the tool. The little plastic bit doesn't do anything to hold them in place. I bet the plastic just makes it easier to clean off dust.
They can be replaced by require taking apart the whole tool.
Possible replacement magnet for future reference, and N52 model
Modifying the tool:
The tool is just a stack-up of parts around chicago screws, you can probably take the tool apart and re-arrange the tools if you want. The screws have strong lock-tite on the threads.
The small screws and lanyard/belt clip screws are #2-56, the larger screws are #6-40. -
@ZapWizard said:
Howdy folks,I received my Free P4.
I took a ton of photos comparing the tool to the Charge, as well as took it apart.
Here is a link to the exploded view.Here is the gallery of images.
My biggest gripes are the small file and lack of bit-driver. I am planning a few mods, and I am currently working on a detailed 3D model of the Free P4. I will use this to design a custom fit holster. I do think it is overpriced, but I really like the magnetic opening/closing. I hate needing two hands and finger nails to use my Charge. The P4 will probably become my EDC tool because it is also slimmer than the Charge TTI.
Magnets:
The magnets are 0.251"x0.511"x0.640" (6.37mmx13mmx1.60mm)
The magnets themselves are quite strong for their size. They seem to be high quality. They had small plastic guard, presumably to prevent the magnets from smacking into each other, which is great as Neodymium magnets aren't actually solid silvery metal as many think, they usually compressed powder which is nickel plated, and can break open.
On the inside of the tool the magnets make contact with the flat surface on each of the tools while folded. The magnets will probably pull away any metal shaving from getting into the hinges, but then any build up will collect on this mating surface. The good news is it is exposed enough with the tools deployed that you can probably get in and clean the magnet surface with a stronger magnet.
The magnets are secured by the thin metal springs in the tool. The little plastic bit doesn't do anything to hold them in place. I bet the plastic just makes it easier to clean off dust.
They can be replaced by require taking apart the whole tool.
Possible replacement magnet for future reference, and N52 model
Modifying the tool:
The tool is just a stack-up of parts around chicago screws, you can probably take the tool apart and re-arrange the tools if you want. The screws have strong lock-tite on the threads.
The small screws and lanyard/belt clip screws are #2-56, the larger screws are #6-40.Bravo!!! Well done.It looks like the elastomer bushings could pretty easily be DIY replaced, if necessary.
-
Well done Zap and welcome to the forum !

I'm going to put this here just cause it's cool


-
Very informative post Joshua, thanks.
-
@ZapWizard said:
Howdy folks,I received my Free P4.
I took a ton of photos comparing the tool to the Charge, as well as took it apart.
Here is a link to the exploded view.Here is the gallery of images.
My biggest gripes are the small file and lack of bit-driver. I am planning a few mods, and I am currently working on a detailed 3D model of the Free P4. I will use this to design a custom fit holster. I do think it is overpriced, but I really like the magnetic opening/closing. I hate needing two hands and finger nails to use my Charge. The P4 will probably become my EDC tool because it is also slimmer than the Charge TTI.
Magnets:
The magnets are 0.251"x0.511"x0.640" (6.37mmx13mmx1.60mm)
The magnets themselves are quite strong for their size. They seem to be high quality. They had small plastic guard, presumably to prevent the magnets from smacking into each other, which is great as Neodymium magnets aren't actually solid silvery metal as many think, they usually compressed powder which is nickel plated, and can break open.
On the inside of the tool the magnets make contact with the flat surface on each of the tools while folded. The magnets will probably pull away any metal shaving from getting into the hinges, but then any build up will collect on this mating surface. The good news is it is exposed enough with the tools deployed that you can probably get in and clean the magnet surface with a stronger magnet.
The magnets are secured by the thin metal springs in the tool. The little plastic bit doesn't do anything to hold them in place. I bet the plastic just makes it easier to clean off dust.
They can be replaced by require taking apart the whole tool.
Possible replacement magnet for future reference, and N52 model
Modifying the tool:
The tool is just a stack-up of parts around chicago screws, you can probably take the tool apart and re-arrange the tools if you want. The screws have strong lock-tite on the threads.
The small screws and lanyard/belt clip screws are #2-56, the larger screws are #6-40.Wow... excellent info. Thank you very much ZapWizard

And welcome to

-
So much quoting. :ahhh
-
@ReamerPunch said:
Why do they insist on two blades? Ditch the serrated, and have a proper file.The serrated blade is the most-used implement on my Surge.

-
@Buzzbait said:
.It looks like the elastomer bushings could pretty easily be DIY replaced, if necessary.They look to be simply cut from cord stock. You probably could cut up an o-ring in a pinch if needed.
@SteveC said:
I'm going to put this here just cause it's cool
I look forward to seeing what Leatherman does with the Free series in the future. Regardless of the magnet, the new lock/folding mechanism is far improved. You can see that every implement has the same shape. Modding should be easier also as the parts just stacked up with Chicago screws and washers. No need to have the perfect torque on the assembly screws.
-
I just got my P4 yesterday, and I don't have a lot to add except that I really like it so far, and I think Leatherman really has a winner on their hands.
-
@algernonramone said:
I just got my P4 yesterday, and I don't have a lot to add except that I really like it so far, and I think Leatherman really has a winner on their hands.
Thanks for posting that!
Y'all,
Looks like the elastomer cushions would be an easy fix of needed.

Thank you, Zapwizard, for the work, post and pics! I feel even more comfortable with my purchase now, knowing the elastomer things aren't even bushings, but more like cushions. Splendid.
-
-
@ZapWizard said:
Modifying the tool:
The tool is just a stack-up of parts around chicago screws, you can probably take the tool apart and re-arrange the tools if you want. The screws have strong lock-tite on the threads.
The small screws and lanyard/belt clip screws are #2-56, the larger screws are #6-40.Thanks for the insights, Zap

Can I test your brain on one thing, please? What would be stopping someone buying a P4, and removing the knife layer to make it bladeless, if they lived/worked somewhere where a knifeless tool would be advantageous? I can't see anything beyond needing to shorten the screws a little, except maybe the lock release

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
