Leatherman Free P2/P4 Club and Feedback Thread
-
@powernoodle said:
Timmy L must have slipped some Rohypnol in my drink, because when I woke up this morning I discoverer that I had ordered a P4 from the Leatherman website.Oh well, could've been worse ...
;)
-

Sent fra min FRD-L09 via Tapatalk
-
@Top-Gear-24 said:
Oh well, could've been worse ...;)
That was kinda how I woke up when I realized I had ordered both the P2 and P4 at around 4am the morning they were released and didn't remember doing it. I had not planned on getting both at the same time. Damn sleep-aid induced decisions.

-
can't wait to hear what you think PN 
-
-
Stunning render work there ZapWizard, I would be interested in a holster, especially if it had a belt clip (so you can remove without undoing belt) and especially if it was mounted midway up the tool.
-
So...out of curiosity I emailed Leatherman about the tools popping out when you cut hard wire or snap the pliers open too hard. They said, “It’s a normal function of the tool.” I’m not sure how I feel about that though. It almost seems like they should have disclosed that it might happen.
Sent from my iPad using Tapatalk
-
Translation, they know and hoped not a lot of owners would complain
. They had to have known
. -
I wouldn’t call that a normal function ???
-
What else can they say?

They can't say it's not meant to happen, or they'll be inundated with warranty claims, or people wanting their money back. They also can't fix it, or the tools will become difficult to deploy. The only thing that will change anything, is if people start suing for injuries occurring as a result, and then it's recall time.
-
If someone gets injured from that, they need their license to use tools revoked. IMO
The cutting blades don't pop out and couldn't if they wanted.
Tried to see if I could hurt myself doing that in several different ways, but haven't been able to.
Not saying it is ok that the drivers play peekaboo, just saying it probably isn't a serious problem. Most likely why they put a flat driver tip on the awl, since that would have been the only poking culprit. The opener/flat edge, and awl/driver edge face inwards to the handles, so the likelyhood of cutting oneself that way would be virtually impossible, unless someone intentionally set it up. -
Considering the time spent on this tool, I can think a number of solutions off the top of my head that might fix this. No idea why they are saying "as intended" which makes no sense.
Frankly I'd be less critical of the tool if they hadn't trashed every other tool in their marketing. Bad idea, especially when it's not true..."strongest pliers we ever made" ummm surge and ST300 say hi.
-
@Aloha said:
Passion makes great members. Perceptions, well..... we all have them and so I like to remember that we all come here to discuss these wonderful tools called Multitools. Moving forward and continuing forward I am happy these tools are in the hands of you passionate members.I am happy that LM for all our sake has decided to show us that they can produce a quality tool regardless if it is for everyone. Heck we all know there is no perfect tool unless its a modded one

I love a lively discussion even to the extent of one side getting ruffled, so long as both sides respect each other. I believe this continues to be very true within these pages of discussion.
I cannot wait for you GLBM to test the living smurf out of these tools. It serves all of us, LM included. Breaking it or damaging it however wont tell the whole story. We've seen tools break. I just want to see the limits to which the tool can be pushed. Yeah a little sadistic ::)
Well said... Aloha

-
@gadgetman7 said:
So...out of curiosity I emailed Leatherman about the tools popping out when you cut hard wire or snap the pliers open too hard. They said, “It’s a normal function of the tool.”Accidental deployment of implements while using something else is a normal function?

I would have asked for details.
-
@Happy Gilmore said:
Considering the time spent on this tool, I can think a number of solutions off the top of my head that might fix this.Stronger magnets would be an easy one. The implements seem rather easy to deploy as it is now, I do not think they'd be difficult to deploy if the magnets were a little stronger.
-
@gerleatherberman said:
If someone gets injured from that, they need their license to use tools revoked. IMO
The cutting blades don't pop out and couldn't if they wanted.
Tried to see if I could hurt myself doing that in several different ways, but haven't been able to.
Not saying it is ok that the drivers play peekaboo, just saying it probably isn't a serious problem. Most likely why they put a flat driver tip on the awl, since that would have been the only poking culprit. The opener/flat edge, and awl/driver edge face inwards to the handles, so the likelyhood of cutting oneself that way would be virtually impossible, unless someone intentionally set it up.We live in an age where cups of coffee have to warn the person who ordered it that the contents may be hot, and bags of peanuts say "Warning: Contains nuts". Even among tool enthusiasts, there are people who consider non-locking blades to be unsafe. No matter how foolproof you make something, there's always a higher calibre of idiot waiting just around the corner, but with this, they didn't even try. Making tools that accidentally deploy this easily, is not acceptable for a tool maker today, no matter how you try and window dress it.
-
@AimlessWanderer said:
We live in an age where cups of coffee have to warn the person who ordered it that the contents may be hot, and bags of peanuts say "Warning: Contains nuts". Even among tool enthusiasts, there are people who consider non-locking blades to be unsafe. No matter how foolproof you make something, there's always a higher calibre of idiot waiting just around the corner, but with this, they didn't even try. Making tools that accidentally deploy this easily, is not acceptable for a tool maker today, no matter how you try and window dress it.Interestingly the coffee thing was quite serious. I found out the real story behind it recently and feel bad for what I thought of the woman before...who was a passenger....elderly....and nearly died....from 3rd degree burns to thighs and lady parts... She spend nearly a month in the hospital I believe. She wasn't the only one, and the coffee at nearly all the McDonald's was approaching 190 degrees F.
As far as the free goes..yeah, the magnets were the easiest possible solution, and likely wouldn't have needed to be that much stronger. Also contact area of the tools to the magnet... The more steel there is in contact...the stronger the bond could be fixed by removing some steel at bottoms of the tool to make more surface area contact.
Cheers
-
The flat on each tool is the same size as the magnet. I don't think removing any metal would help. The gap between the tool and the magnet is tiny. Just enough to ensure the magnet doesn't get slammed into the tool upon closing.
I don't know if the magnets inside are the highest strength or not, but one easy mod would be to replace them with maximum strength N52 class magnets.
-
@ZapWizard said:
The flat on each tool is the same size as the magnet. I don't think removing any metal would help. The gap between the tool and the magnet is tiny. Just enough to ensure the magnet doesn't get slammed into the tool upon closing.I don't know if the magnets inside are the highest strength or not, but one easy mod would be to replace them with maximum strength N52 class magnets.
That could cause other potential issues. I'd try to add a small amount of metalic putty to the bottom of the tools to allow more contact but have some give from the putty. Also not voiding warranty
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
