ZapWizard's Leatherman Free P4 Mods
-
Some thoughts in order...
a)

b)
c)
d) how possible is it to have the belt clip central? (don't like the tool carrying too low)This is amazing though, love the pics and the insight into the process.
-
Seriously.** I WILL be anxiously awaiting the results of the mods. **

Thank you for all of your efforts so far, ZapWizard.

-
@aussieman said:
d) how possible is it to have the belt clip central? (don't like the tool carrying too low)The belt clip holes are #2-56 drilled and tapped holes in the scales. Drill and tape your own holes to put the clip anywhere you want. Just provide some protection to prevent the shaving from getting on the magnet. Or take it apart beforehand.
-
My interest in the p2 is now directly proportional to your progress on this project. I do some design on OnShape for 3d printing projects, but your work is truly next level. Really wish I had your skill set.
Cheers,
HG -
Note: I am not designing for the P2 at this time, just the P4 that I own. The P2 is a bit pricey. I can't afford to purchase every single possible tool.
-
I must as a question unrelated to your VERY IMPRESSIVE work here. The Chicago screws that are used as the pivot for the tools look to be 4 mm in your photo. Is this actually the case? I have a project that I can't seem to get off the ground because I can't seem to find a 4 mm pivot.
-
@ZapWizard said:
Note: I am not designing for the P2 at this time, just the P4 that I own. The P2 is a bit pricey. I can't afford to purchase every single possible tool.I believe the p2 has the same space and frame so it should accept any bit exchanger u design for it as well. That is what I was referring to.
-
@Douglas said:
I must as a question unrelated to your VERY IMPRESSIVE work here. The Chicago screws that are used as the pivot for the tools look to be 4 mm in your photo. Is this actually the case? I have a project that I can't seem to get off the ground because I can't seem to find a 4 mm pivot.The screw post are smaller than 3mm. It's the same size LM uses for the rivets on the juice series. 4mm? Spirit?

-
Smurf yeah! Very excited about this thread!!

-
:D I also have problem sourcing for that. Buying them standalone will be difficult. At least for where I am. I have realise alot of non mainstream brands, those made in China uses metric size pivots. Very common are 5mm and 4mm. And they are often cheaper than buying just the screws. Strip them for their parts.
Sorry for hijacking the thread!

-
@Douglas said:
The Chicago screws that are used as the pivot for the tools look to be 4 mm in your photo. Is this actually the case?It was quite hard to determine some of the parts, as Leatherman uses a mix of Imperial and Metric measurements. I used thread guages and calipers to determine the screw sizes.
The chicago screw tool pivots near the pliers are #6-40 threaded posts, with a diameter of 3/16" (4.76mm), and 5/8" (15.84mm).
The chicago screws at the blade end are #2-56. 3.1mm diameter, and 16.7mm long.
@Happy Gilmore said:
I believe the p2 has the same space and frame so it should accept any bit exchanger u design for it as well. That is what I was referring to.Gotcha, yes that should be the same.

Here is an early image of the design for a bit holder.
It would be made from 3d printed steel. It would keep the can opener (as long as prototypes show it has a strong enough hold on the tool) It also would gain a 1/4" hex opening were the opener is.
The bit would be held in by a magnet.Fitting the flat leatherman bit into the space left in the P4 was tricky. What I ended up having to do was offset the bit holder by five degrees. But that would make it off axis when open. I then realized I could offset the open lock by the same angle, and make it straight when open.
This one will require quite a bit of time to develop as the 3D printed steel can shrink sort of like a casting, and I also have to get the locking mechanism to work just right.

This is the final rendering for the P4 holster with normal belt loop. I am still working out a few other attachment loops, clips and methods to suite the various requests I have received in the past.
-
Excellent work ZapWizard

-
Awesome work!

-
That flat bit driver looks excellent

-
A bit driver...can opener and 1/4 inch driver....we are not worthy, not worthy!

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
