ZapWizard's Leatherman Free P4 Mods
-
@Douglas said:
I must as a question unrelated to your VERY IMPRESSIVE work here. The Chicago screws that are used as the pivot for the tools look to be 4 mm in your photo. Is this actually the case? I have a project that I can't seem to get off the ground because I can't seem to find a 4 mm pivot.The screw post are smaller than 3mm. It's the same size LM uses for the rivets on the juice series. 4mm? Spirit?

-
Smurf yeah! Very excited about this thread!!

-
:D I also have problem sourcing for that. Buying them standalone will be difficult. At least for where I am. I have realise alot of non mainstream brands, those made in China uses metric size pivots. Very common are 5mm and 4mm. And they are often cheaper than buying just the screws. Strip them for their parts.
Sorry for hijacking the thread!

-
@Douglas said:
The Chicago screws that are used as the pivot for the tools look to be 4 mm in your photo. Is this actually the case?It was quite hard to determine some of the parts, as Leatherman uses a mix of Imperial and Metric measurements. I used thread guages and calipers to determine the screw sizes.
The chicago screw tool pivots near the pliers are #6-40 threaded posts, with a diameter of 3/16" (4.76mm), and 5/8" (15.84mm).
The chicago screws at the blade end are #2-56. 3.1mm diameter, and 16.7mm long.
@Happy Gilmore said:
I believe the p2 has the same space and frame so it should accept any bit exchanger u design for it as well. That is what I was referring to.Gotcha, yes that should be the same.

Here is an early image of the design for a bit holder.
It would be made from 3d printed steel. It would keep the can opener (as long as prototypes show it has a strong enough hold on the tool) It also would gain a 1/4" hex opening were the opener is.
The bit would be held in by a magnet.Fitting the flat leatherman bit into the space left in the P4 was tricky. What I ended up having to do was offset the bit holder by five degrees. But that would make it off axis when open. I then realized I could offset the open lock by the same angle, and make it straight when open.
This one will require quite a bit of time to develop as the 3D printed steel can shrink sort of like a casting, and I also have to get the locking mechanism to work just right.

This is the final rendering for the P4 holster with normal belt loop. I am still working out a few other attachment loops, clips and methods to suite the various requests I have received in the past.
-
Excellent work ZapWizard

-
Awesome work!

-
That flat bit driver looks excellent

-
A bit driver...can opener and 1/4 inch driver....we are not worthy, not worthy!

-

I thought I had a good design for the thumb-tabs, and had SLS prototypes in hand last week.
The design was three small tabs held together by a sprue to reduce costs (Shapeways charges per-part)

In CAD these flat-head screws were supposed to be just a bit bigger than the slot, and they would secure the thumb tabs to the blade without any glue needed.
They are tiny #0-80x1/8L screws. But reality turned out that they fit through the slot, and were nearly impossible to thread into the tiny blind holes.

The prototypes did show they work pretty well. It makes it easier to open the blade, and easier to keep you thumb on one spot through the whole opening process.
However, I had to redesign them to figure out another securing method besides super glue.

This is the new design. It uses either #1-72 or M2 set screws. The set screws go almost the full length of the thumb tab. This time the hole they go into is tapered.
The top edge is set to that it should start to thread easily. Then the hole tapers down to the point that the hole is undersized. This along with a split in the back should make it so that the screw clamps the plastic sideways into the slot.
We will see once the second revision arrives.

The holster, driver, first run prints have all been ordered I didn't pay extra this time for rush processing, so it will be almost a month before I get them in my hands.
-
Wow. Very nice. Any guess on costs?
-
Pricing should work out to be $39 for the holsters (Same as my others), $25 for the bit holder, and $14 for the thumb tabs. Those prices are mostly Shapeways production costs.
-
@ZapWizard said:
Pricing should work out to be $39 for the holsters (Same as my others), $25 for the bit holder, and $14 for the thumb tabs. Those prices are mostly Shapeways production costs.OMG that is so reasonable for the bit holder. Any chance of designing a 1/4" hex bit holder for the wave/charge platform? If anyone can, you probably could.
-
:o Some very nice work, Zap

-
My production holster arrived today!
The good news is no design changes needed. Those seven previous prototypes paid off. The holster works perfectly. The tool snaps in with a satisfying click and is very secure with no rattling. It is slightly less secure when docked upside down due to the spring angle, but still good enough not to fall out if shaken upside down.
I did record a nice video showing off everything. But it turned out to be too blurry and with too much wind noisey. (Dead cat's don't work as well as they should). I will record another video once I get some time later next week.
The new production thumb tabs also arrived, along with the tiny set screws. They also fit perfectly and look great. The expanding set-screw lock worked like a charm.
Both of these are available on my Shapeways store. The link is in my signature.
The swappable bit holder also is here, but will require some drilling and more experimentation which I don't have time for this week. The bad news there is it probably will need to looe the bottle opener, as some Leatherman bits just don't have enough surface area at the back to fully engage with the magnet, and are weakly held right now.
-
That looks absolutely beautiful! :o :o :o

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login



