Gathering thoughts/tools/materials for first mod
-
@Dutch_Tooler said:
I bow to your greater training and experience Vidar
Not really much to bow to! You should have seen my former collection of "things gone spectacularly wrong and bits of metal which tried to maim or kill me". That is not counting various attempts of electrocuting myself, setting myself on fire, chemical exposures or doing stupid things with heavy machinery. :ahhh Training is clearly lacking, although I guess that might count as experience :D
-

Your remarks about not trying M1.5, leaving enough hole depth for tapping residue and retracting the tap every few turns are spot on, sorry for omitting them in my list.
As to precision, even drilling and tapping slightly off-axis isn't going to break the bank as long as you don't exaggerate. In addition, what I have found necessary anyway is to make the pivots a little bit longer than necessary, then shortening them to the required length while in position in the knife using a drill bit that has the size of the (tapered) screw head (4.5 mm IIRC) to match its taper and make the head's outer surface flush with the scale (by hand, i.e. drill bit in hand driven chuck and using utmost care).
This is also one of the reasons that I can't simply work to order - each pivot is fitted in place.
Edit: don't forget the Loctite...
-
@Dutch_Tooler said:
As to precision, even drilling and tapping slightly off-axis isn't going to break the bank as long as you don't exaggerate.True. I guess I've just had some traumatizing manual tapping experiences, and thus I go about things really carefully if I have to do it. Probably too careful if one considers what the machines do in comparison. I guess I should propose a law: "The more expensive or more finished a part is, the greater the chance of a tap breaking inside a hole". It is right up there with single socks!
A subsupplier many years ago just put a tapping head on a normal hand drill, eyed it at about 90 degrees, and tapped every hole in sight in a real hurry. That was in aluminium though. Still worked amazingly well - you couldn't even drill at that speed.
-
@Vidar said:
Come to think of it there might be something like a maker space in Hong Kong? Some of those places seem to have lots of equipment people can use. Probably also with some people who knows who to use it :)I looked pretty hard for that, but mostly what I see are some casual 'workshop', where people just show up for an hour or two, and expect something coming out from it(Watch band making, carved spoon with tools, etc). There might be some classes offered in University, but you probably have to enroll to get to play with the toys, and I'm not sure there is access to the machines afterwards.
I guess it is the 'instant noodle' culture, where people just want instant gratification without putting having to put in any real work.

I don't know whether I can speak for other beginner modders, but to me, modding is not just about making desirable products, but it is also the things you learn and people you get to know which is an adventure in itself. :D
-
The tapping of pivot sounds rather intense, and am not sure it is way beyond me...maybe someday, if I got hooked so deep that I got a mini lathe, even then I am not sure it will be easy to do.

So if I got a decent enough drill press, sounded like drilling out all the tools in the 93mm tools and using the 1/8 pivots from knifekits.com is the way to go...or if I am lucky enough, finding someone who could make those tapped pivots and sell it.
:D -
@comis said:
The tapping of pivot sounds rather intense, and am not sure it is way beyond me...maybe someday, if I got hooked so deep that I got a mini lathe, even then I am not sure it will be easy to do.
Ah, just find something to practice a bit on - maybe with some bigger holes at first. There really isn't much to it, and afterwards you'll be making threads and screw stuff together all over the place :D
@comis said:
So if I got a decent enough drill press, sounded like drilling out all the tools in the 93mm tools and using the 1/8 pivots from knifekits.com is the way to go...or if I am lucky enough, finding someone who could make those tapped pivots and sell it.
:DIf the pivot is 3mm just get something actually 3mm? Come to think of it, check out something like "EDM drilling electrode single hole 3.0". A bit of search and you have a some straight rods at exactly 3.0 outer diameter with a ready hole throughout the middle. You just need to make it a little bigger, but it will provide steering. For example this place:
https://www.aliexpress.com/item/32681859509.html?productId=32681859509&productSubject=Ziyang-Brass-Electrode-Tube-Single-Hole-3-0-500mm-for-EDM-Drilling-Machine (Make sure to specify "single hole" as for 3mm multi-hole is more common). -
On that latter note, I have bad experiences with pre-made holes... better drill yourself
-
@Dutch_Tooler said:
On that latter note, I have bad experiences with pre-made holes... better drill yourselfDo you want to talk about it? :) The holes of an EDM electrode should be exactly in the center throughout.
Edit: Just curious of the issues? Come to think about I might have some EDM electrodes around here somewhere. Probably not 3mm though.
-
@Vidar said:
Do you want to talk about it? :) The holes of an EDM electrode should be exactly in the center throughout.Edit: Just curious of the issues? Come to think about I might have some EDM electrodes around here somewhere. Probably not 3mm though.
I did some sourcing for brass tube that is 3.0mm OD and with threaded hole of 2.0mm (for M2 screws) in Chinese websites, but almost 99% of the time, the tube I see are not smooth outside, but with grooves. And the real 'diameter' with grooves are usually around 3.2mm. I have seen MTO member trying to smooth out the outside by sanding it down. However, I just have no data whether those pivots did hold up in a long run. Follow this link here.
That lead me thinking...what if the 'sanding' down is done by a lathe? That's should be far easier to trying to tapper thread into a long rod, is it?
-
My bad experience was in trying to enlarge a hole to 1.5 mm, it must have been around 1.1 or 1.2 to start with. Drill bit broke off. The rolling process they used for that type of brass tube (3 mm outer diameter) must have caused a harder inner surface in places. I had some rod stock and that worked better ;)
-
@Dutch_Tooler said:
My bad experience was in trying to enlarge a hole to 1.5 mm, it must have been around 1.1 or 1.2 to start with. Drill bit broke off. The rolling process they used for that type of brass tube (3 mm outer diameter) must have caused a harder inner surface in places. I had some rod stock and that worked better ;)Just for reference, I remembered reading Syph too were saying the same thing regarding drilling threaded tubes, and mentioning it might be easier to do it from a solid rod.
-
@Dutch_Tooler said:
My bad experience was in trying to enlarge a hole to 1.5 mm, it must have been around 1.1 or 1.2 to start with. Drill bit broke off. The rolling process they used for that type of brass tube (3 mm outer diameter) must have caused a harder inner surface in places. I had some rod stock and that worked better ;)The biggest electrode I have is 2.5mm. I think these are made by extruding brass so they should be fairly even. I might drill a slightly bigger hole just to get a feel.
@comis said:
Just for reference, I remembered reading Syph too were saying the same thing regarding drilling threaded tubes, and mentioning it might be easier to do it from a solid rod.Electrodes are not threaded in any way. Just a small smooth hole in the center.
@comis said:
I did some sourcing for brass tube that is 3.0mm OD and with threaded hole of 2.0mm (for M2 screws) in Chinese websites, but almost 99% of the time, the tube I see are not smooth outside, but with grooves. And the real 'diameter' with grooves are usually around 3.2mm. I have seen MTO member trying to smooth out the outside by sanding it down. However, I just have no data whether those pivots did hold up in a long run. Follow this link here.That lead me thinking...what if the 'sanding' down is done by a lathe? That's should be far easier to trying to tapper thread into a long rod, is it?
Making threads isn't actually difficult. Just make a nice setup and do the steps. Easiest way with a drill press might be to fasten a piece of wood or something. Then just don't move the wood for the following: Drill a hole of 3mm, make the wood hole clampable, stick the rod end in and clamp it, change drillbit to 1.6mm, drill hole, change drilltip over to tap and tap hole. That way they should all line up perfectly. (In a lathe just clamp it directly instead of in the wood).
That said removing some outer grooves could work fine as well. I would have gone for threading a rod I think, but then I again I do have tools handy.
-

Looks like you are in good hands comis

-
Looks like you are in good hands comis

No doubt about that!

Next is to find myself a drill press for the 93mm mods, it may take sometime. Meanwhile, I would have the hand drill soon which should allow me to do the 91mm mods(project A, Mountain Explorer), and practice on dummies/donors on cheap bids. I will probably make a new thread if I run into any trouble, or share the DIY experience. :D
-
Hi, all!
Just wanna share a quick update after all these posts. :D
Finally gotten a drill press and am quite happy with it, nothing state of the art, but from a traditional well-known brand which has been making drill press for last 50 years. In case anyone is curious, it's called the "Wesk Lake", model ZQ4113. It's a 370W B-taper drill press and weights around 70kg.

For the past week or so, I had taken my own sweet time disassembling two SAKs from beat up lot sale--a 91mm Climber and a 93mm Alox (it's a weird combination of openers and large blade+electrician blade), making drawings and scanning the liners etc. Up until then, everything was like dream, easy pants.
Then yesterday came, I started trying peening the 93mm...and that's where my nightmare begins. There were three pins, and I figured I will try different hammers/concave punch/technique on different ones. First pin I used a 10+ oz hammer just bent rather quickly.

Second and thrid pins, I was counting on those "concave punches", and did mod them a little bit to fit the top shape of alox rivet. But despite my best effort with a 2 and 4oz hammers, it felt like it is not moving any metal, and they were merely pushing very modest material down the side of pin, form a thin layer of muchroom. The shape of it looks good from the outside, but upon drilling them out for inspection, the brass didn't fully fill up the countersink hole, so those concave punches seem like are only good for the cosmetic?


Today, I figured I will redeem myself with doing something simpler, the 91mm. I left around 0.5mm material above each side of the bushing, and just peen away with a 4oz ball peen hammer, then 2 oz hammer...everything went kinda well up until the final stage of peening away a very small play. Then I realized I somehow managed to put the tools in the wrong order in the mist of all things. No smurf, there I thought I gonna pretend I was half good at peening, and something else got the better of me. No smurf!


Everything looks orderly, on a jig...

Then this smurfing dumb move happens, and I was busying taking photo documenting my dumbness...


The small blade supposed to be closest to the liner...then the large blade with space. I should have checked and played with all tools earlier, that might have prevented that.

A comparison between original pins(bottom two) and my own peened pins(top three), I was still about 5-10% away from no play, but at least happy to see the ball peen did move some material down into the countersink alright.Few questions and observations after these peening practices:
-
How much material should I leave on each side of my 93mm alox before I start to peen? I tried 1mm each side, it's kinda ok, but 0.7mm each side don't seem to have enough material to fill the countersink and form a decent 'dome' shape
-
I found concave punches are not doing me any good for peening, anyone using them instead of ball peen hammer? It's not really 'moving' the metal like the ball peen hammer, and I worry it doesn't move enough material down the countersink on the Alox rivet hole...
-
While leaving material on each side, I tried this one technique to push the entire knife flat against the anvil before peening(so any extra pin materials will be pushed up thru the holes), but I was wondering whether I should tried to keep the pin material equal on both sides of the knife while peening. Is there any difference?
Thanks for reading!

-
-
Yay! A drill press - congrats!

As for the riveting I'm sure others here have more experience with SAK rivets than me.
-
@comis said:
While leaving material on each side, I tried this one technique to push the entire knife flat against the anvil before peening(so any extra pin materials will be pushed up thru the holes), but I was wondering whether I should tried to keep the pin material equal on both sides of the knife while peening. Is there any difference?]I did that myself, which led to my backside peening to be larger than the front ones.
I'm sure you can get it exactly the same if you switch the side you're peening, alot.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login