Gerber Mr. Pinchy Multi Plier Club
-
@gerleatherberman said:
More updated Pinchy pics!Excellent assortment of Mr Pinchies, GLBM

-
@gregozedobe said:
Excellent assortment of Mr Pinchies, GLBM

Thank you much, Greg!

The only Pinchy I can think of that would kind of round the set off is a BO V.4.
Are there any important oddball versions I'm missing that you know of, Greg?
Just as something to keep an eye out for later down the road. :) -
@gerleatherberman said:
Thank you much, Greg!
The only Pinchy I can think of that would kind of round the set off is a BO V.4.
Are there any important oddball versions I'm missing that you know of, Greg?
Just as something to keep an eye out for later down the road. :)Here is an updated version of a list I wrote a while back (the major change is the addition of v1.1.5 ), hope that helps:
I copied much of the following info from a earlier post on MTo (possibly by Bob ? ), with revisions and additions from looking at various Mr Pinchies (and some assumptions on my part). Naturally any errors/omissions are my fault. If anyone has any corrections and/or extra info please speak up (eg which versions were made with a BO finish). Sorry, I can't do photos. I hope this helps out all those interested in the development of gerber's (in)famous "Mr Pinchy".
**EARLY GERBER MULTI-PLIERS ("Mr Pinchy") **
Gerber kept making small changes to their Multi-Plier throughout the 1990's, so we tend to see a lot of subtle variations. Some were stamped and sold with the Fiskars logo, and at least some of these had slightly different tool loads (Fiskars owned Gerber at that time). At some stage Gerber started making a BO finish available, as well as the much more common bead blasted SS finish. Here's a summary of the main steps along the way:
Version 1) The very first models had a high-polish finish, instead of the bead blast we've seen on Gerber tools since. It also had button-head screws in all four blade pivot points, and button head screws on the plier slides. Also note the pivot bushing between the plier jaws. A crude pair of scissors was included, and a VERY thick Lanyard clip. The very first run of Multi-Pliers were etched with “FIRST PRODUCTION RUN” (a.k.a. “FPR” ) on one handle.
V1.0 FPR
V1.1 One handle cut-out, mis-matched nail nicks (don’t line up with cut-outs)
V1.1.5 One handle cut-out, matched nail nick on PE blade, mismatched nail nick on SE blade
V1.2 One handle cut-out, matched nail nicks
V1.2 Two handle cut-outs, matched nail nicksAll ? “PATENT PENDING”
Version 2) The second version went to the now-familiar bead blast finish. The scissors were replaced by a big triangular shaped awl. This version still has button head pivots, button head sliders, and the pivot bushing between the plier jaws. The pliers had slightly beefier jaws with a squarer shape, while the lanyard clip was slimmed to a more “normal” thickness. There seems to have been some variations in the font of the labels on the handles.
V2.0 “PATENT PENDING”
V2.1 “U.S. PATENT NO 5142721”Version 3) This version wasn't much of a change really. They simply did away with the pivot bushing. Later production V3s had the round nut on the handles.
All ? “U.S. PATENT NO 5142721”
Version 4) Changes: On one side of each handle, the button head screw was replaced with a round nut, while a file replaced the large awl.
V4.0 “U.S. PATENT NO
5142721/5142844” NB The 5142844 # was possibly an error, as later versions all used 5212844.V4.1 “ U.S. 5142721
PATENT 5212844
PAT PEND”**Version 5) ** This introduced a new, even beefier shape to the blunt nose plier jaws, and needle nose jaws were offered for the first time as well. Gone were the button head slider screws, replaced by two different sizes of round-headed rivets.
All ? “U.S. 5142721
PATENT 5212844
PAT PEND”At this point Gerber stopped with the minor evolutions of the Multi-Plier (Mr Pinchy) and came out with a major overhaul. Called the Multi-Lock when it first hit the market, the new tool had all-locking blades, plastic sliding lock releases, unique blade-pivot screws, the now familiar little circlip spring steel slider clips, etc.
After a while this tool became the 600-series Multi-Plier (MP600), with all its many tool component and plier type configurations. The very first ones were also stamped "First Production Run" (FPR).
All ? “U.S. 5142721
PATENT 5212844
PAT PEND” NB This is stamped inside the handle, not externally as before (and in a very small font).This information was last updated by gregozedobe on 6 March 2019
Note there are are quite a few odd-ball Mr Pinchies floating around, some are definitely prototypes, others seem to be transitional variants with components/handles from two different versions (or they could be repair jobs by Gerber or private individuals). Substituting the awl for the file seemed to happen a bit on some later versions (and on all the Fiskars labelled ones I've seen) . BO variants are way less common then their SS counterparts.
-
Wow! Great list and information. Thank you, Greg!

Looks like I need to reclassify some of the ones I listed, based on the information. Will do that at some point today.

I felt lucky getting a V1 BO and V2 BO, as they seem to be extremely rare. :ahhh
The biggest difference I've noted with what I've been calling V3s, is that there are two very different pliers designs. One with a classic smaller plier pivot and clean casting and ones with a larger pivot and casting flaw in the mounting areas.
-
Top row:
V1.0 FPR, V1.1 BO, V1.2 SS, V2.0 SS, V2.0 BO, V4.1 BO(older pliers head), & V3 SS.
Bottom row:
V4.1 SS(older pliers head), V5 BN SS, V5 NN SS, Fiskars(with awl and file - awl instead of can opener - factory), CK&T old, & CK&T new.I'll take an updated photo at some point as well to put the V3 before the 4.1 BO.

-
Here are two photos showing(what you've designated V4.1) the two different pliers heads on the 4.1. All of this(with 5142721/5212844/PAT.PEND on handles) have either og these two pliers heads from what I have seen. And the later, larger pivot, usually has casting flaws in the mounts. Doesn't hurt the function, but is cosmetically ugly.
The two different heads, and both have the small nut/bolt fasteners in the pivot centers.

The inside, where the casting flaws are obvious.

Some early MP pliers heads also had casting flaws aound the mounts, but not as gnarly as the flaws on the lg. pliers pivot on the 4.1.
-
@gerleatherberman said:
Doesn't hurt the function, but is cosmetically ugly.
-
Basically. Yeah.

-
<u>Corrected order and version designations.</u>
V1.0 FPR, V1.1 BO, V1.2 SS, V2.0 SS, V2.0 BO, V3 SS, & V4.1 BO(older pliers head).
Bottom row:
V4.1 SS(older pliers head), V5 BN SS, V5 NN SS, Fiskars(with awl and file - awl instead of can opener - factory), CK&T old, & CK&T new.Full view.

Top row close.

Bottom row close.
]Top row open.

Bottom row open.

Top row side-by-side.

Bottom row side-by-side.

-
New member. Only got the one though >:D

-
@Dutch_Tooler said:
New member. Only got the one though >:DVery nice, D_T!

A must-have for any MT enthusiast and a real piece of MT-history.

-
Thanks

First impressions:
It feels solid and hefty, yet compact; very beefy sheet metal used for the handles. Built for life. Better feeling in that respect than the CD I idly handled at Paragon when I bought the Wave+ last year. Quick-draw stubby nose pliers (refreshing after all these needle nosed ones on all the tools nowadays). Nice file too (much better than what SOG offer currently). Inner implement extraction is a multi-step procedure though.There is a little bit of rattle in the slider mechanism - I wonder if I can tighten the slider screws just a tiny bit without impeding the sliding movement. I assume these are loctited?
-
No need to worry about the rattle. That is inherent to all sliding pliers Gerbers. That is why I am always yapping about the Multi-Pliers being the most reliable MTs made. Loose tolerances makes for tools that hold up longer than tight tolerance tools. :)
You can try tightening the screws possibly, but the loctit is so old it break free easily without heat. Tightening will make the tool less confidence
And for grip/splat, the Multi--Pliers is a bear. .

-
Pinchy fun-night.







-

An impressive array GLBM

-
An impressive array GLBM

Many thanks, D_T!

Just two more Pinchy versions to locate and I will consider the OG Multi-Plier group complete. A BO NN V.5 and a BO BN V.5. :ahhh
-
Hello - I am new to this forum (actually, any forum) so ask for leniency as I probably commit forum-etiquette faux pas. I inherited this Gerber multitool and while I fancy my internet search skills I can't for the life of me figure out what model this is -- or what the purpose (tool) the hook is. I mean, I get the basic idea of a hook, but I've never seen a hook like this on a multitool ...
I asked Gerber (twice) but never got a reply. I hope I attached the picture properly. Any assistance anyone has is greatly appreciate.
Thank you.jpg)


.jpg)
-
Early Trailrider perhaps? Looks like a hoof pick. Either it is a really rare Trailrider-type run, a prototype equestrian MT, or someone made it(to act like the later Trailrider).
Welcome to MT.o, Go Army! -
@gerleatherberman said:
Early Trailrider perhaps? Looks like a hoof pick. Either it is a really rare Trailrider-type run, a prototype equestrian MT, or someone made it(to act like the later Trailrider).
Welcome to MT.o, Go Army!Thank you - took me a few seconds to even figure out how to reply. I thought about the trail rider but that looks like a more pronounced "L" than this hook. Based on your experience does this seem a factory-type tool or more, as you say, a sort of made-up tool? do you think this is an original? I'm not concerned about value, just trying to figure out what this is .. the other Gerber I have was a gift from the Army for a trip to Iraq and that one is easy to find out about -- so really just sort of fascinated by this (hoping it's not counterfeit, as I'd hate to unwittingly support that indirectly). Thanks
-
Welcome to the boards mate.

Have a look around the pivot area and see how well the machining matches up with the other tools.
It's definitely a cool piece.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login