Leatherman Free P2/P4 Club and Feedback Thread
-
@gerleatherberman said:
Welcome and congrats on the P4, jorritvS! Thank you for sharing!
...
-
@jorritvS said:
I didn't grind anything off for it to fit. I also wouldn't do that on a tool this expensive. It just fitted without any modification necessary. That is also why I like it and why I did share it.Sent from my ONEPLUS A3003 using Tapatalk
Thanks for clarifying!

Will have to dig through the spare parts bins this evening. :)
-
I bed the bit the adapters to fit no mods needed to the tool. Here is an old post on how I do It. /topic/20136
-
Bad experience today while using the scissors on the P2. When to close it(one handl) i could not do it, it stuck. What the hell, i was thinking to myself.
The back latch came off position. Inspecting it closer, the sexbolt was reall loose, almost completely unscrew and the handels distanced themselves so the back latch came off position.
I never touched the P2, just the P4 i dissasembled completely. The P4 had loctite on all the sexbolts, yet this P2 seems it just smelled some loctite.



-
I was at home, so no stress, i cleaned the bolt and applied new loctite on it, YET WTF LMN, what if this happened in the field and you loose the bolt and maybe other pieces.
For safety reasons i checked the other part. Bolt was in place(not unscrewed) yet with the screwdriver it felt loose. Same thing, this one did not even smelled the loctite in the factory.

-
I think someone else had a P with little or no loctite on the screws? Sam I think?

The P4 I use didn't have much, but I did need to heat it up to turn more freely, as there was a little on each screw thread.
I wonder if the assembly person just didn't bother using much, if any, loctite on Friday afternoon before close?
-
@gerleatherberman said:
I think someone else had a P with little or no loctite on the screws? Sam I think?
The P4 I use didn't have much, but I did need to heat it up to turn more freely, as there was a little on each screw thread.
I wonder if the assembly person just didn't bother using much, if any, loctite on Friday afternoon before close?
Yeah I think that was me. I did feedback before sometime earlier. But being someone that cannot live with stock, I personally think it's somewhat better this way. That screw is really tiny. If it gets stuck with locktite somehow, it can break inside. Those that had experience with small pivot screws will know. Be it a Vic or juice. Most should experience some sort of breakage..
-
I used to do a lot of modding not so much lately. I do enjoy seeing all the creative mods you guys come with. Look forward to seeing what come up with.

If anyone has an extra kick pocket clip pivot I trade one of my bedded P-2 bit adapters for it.
-
After another week of use, today i observed an issue.
I have used the pliers and i have applied a small amount of force on the handles to hold something fermly( i had to unscrew an M10 bolt and i hold the nut with the pliers).
Interestingly, the pliers have become stiff, immediately i felt them to be too stiff to my likening and to what i have been used.
I applied some oil and opened and closed the pliers several times. This is affecting the easyness of closing the tool.
When it became slightly easy for the pliers to be opened, after several hundreds closing and opening, i squeezed the handles again, nothing in the jaws of the pliers, and again it became stiff.
WTF, something is not OK in the area of the Pliers PIVOT -
That happens sometimes to other LM models too.
It can go away after some time of use, however, I've read reports where it didn't seem to.It can be that the pivot is slightly oval in shape (inside) which could introduce such behavior

-
@MTMatt said:
That happens sometimes to other LM models too.
It can go away after some time of use, however, I've read reports where it didn't seem to.It can be that the pivot is slightly oval in shape (inside) which could introduce such behavior

Sounds like warranty worthy, but maybe not possible after the mods? Yes, that had been an issue across the board with pliers.
-
@Raoul Octav said:
After another week of use, today i observed an issue.
I have used the pliers and i have applied a small amount of force on the handles to hold something fermly( i had to unscrew an M10 bolt and i hold the nut with the pliers).
Interestingly, the pliers have become stiff, immediately i felt them to be too stiff to my likening and to what i have been used.
I applied some oil and opened and closed the pliers several times. This is affecting the easyness of closing the tool.
When it became slightly easy for the pliers to be opened, after several hundreds closing and opening, i squeezed the handles again, nothing in the jaws of the pliers, and again it became stiff.
WTF, something is not OK in the area of the Pliers PIVOTThis helped me immensely.
/post/1952289
-
I just tried the awl on my leather belt. I was a bit skeptical but it surprisingly punched right through it.
-
@genevabuck said:
I just tried the awl on my leather belt. I was a bit skeptical but it surprisingly punched right through it.
I also have had good luck drilling mid-size holes in wood to start screws. :)Just can't start really small holes like can be done with a pointed awl.
-
So, got my P2 and P4, sold my Charge TTi and Signal... Loving them mostly, apart from the difficulty opening blades and the way too fat pocket clip.
But very curious to see different parts being used for the scissors. The P4 scissors don't provide any resistance when opening for the first thirty degrees or so. The P2 ones snap back. You can see they changed the profile, and you can see this in action as you deploy the tool. The P4 scissors won't move the lock for some time.
The P4 is marked 04/19 and came with the new pocket clip. The P2 doesn't have a date stamp, both bought Amazon/Netrush in USA June 6.

-
Strange. On my P4 (no date stamp) the scissors are those in your P2 pic side. Seems they have modified the scissors on newer runs. Hang on to that P2, it might become rare :D

-
@Dutch_Tooler said:
Strange. On my P4 (no date stamp) the scissors are those in your P2 pic side. Seems they have modified the scissors on newer runs. Hang on to that P2, it might become rare :DSame on my P4 (which does not have a date stamp, however, on the place where they put the date stamp on the "new" Free tools, mine says 1 2 1, only on the side of the phillips
). -
Decided to take care of the pant's pocket destroying screws on my P4.
The P4 clip LM sent came with an extra set of screws, so I used those just in case I sent a screw flying across a messy workshop.
I filed the slot out a little in the end of a clockmaker's pin vise to hold the machine screws while grinding and polishing. There really isn't another good way to hold these screws(they are so short) without damaging the threads, so be careful using anything to hold the screws. The soft steel of the pin vise and dispersion of surface contact(from filing the opening to seat the screw a bit better) did not damage the threads any.Before.

Pin vise with hole notched out.

Screw secured in pin vise.

After spinning it against a fine grinding wheel.

Screws installed after some steel polishing to smooth the screw heads out.

-
GLBM, that looks good.
JonesE
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
